SIST EN ISO 12224-3:2003

SLOVENSKI STANDARD
SIST EN ISO 12224-3:2003
01-december-2003
0HKNHVSDMNHYREOLNLåLFHSDOLFHLQVWUåHQVNHåLFH6SHFLILNDFLMHLQSUHVNXVQH
PHWRGHGHO0HWRGDSUHVNXãDQMDELODQFHRPRþOMLYRVWL]DXþLQNRYLWRVWPHKNH
VSDMNHYREOLNLVWUåHQVNHåLFH,62
Solder wire, solid and flux cored - Specifications and tests methods - Part 3: Wetting
balance test method for flux cored solder wire efficacy (ISO 12224-3:2003)
Massive Lotdrähte und flussmittelgefüllte Röhrenlote - Anforderungen und Prüfverfahren
- Teil 3: Bestimmung der Flussmittelwirkung von flussmittelgefüllten Röhrenloten mit der
Benetzungswaage (ISO 12224-3:2003)
Fils d'apport de brasage, pleins et a flux incorporé - Spécifications et méthodes d'essai -
Partie 3: Méthodes d'essai a la balance de mouillage de l'efficacité des fils a flux
incorporé (ISO 12224-3:2003)
Ta slovenski standard je istoveten z: EN ISO 12224-3:2003
ICS:
25.160.50 Trdo in mehko lotanje Brazing and soldering
SIST EN ISO 12224-3:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 12224-3:2003

---------------------- Page: 2 ----------------------

SIST EN ISO 12224-3:2003
EUROPEAN STANDARD
EN ISO 12224-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2003
ICS 25.160.50
English version
Solder wire, solid and flux cored - Specifications and tests
methods - Part 3: Wetting balance test method for flux cored
solder wire efficacy (ISO 12224-3:2003)
Fils d'apport de brasage, pleins et à flux incorporé - Massive Lotdrähte und flussmittelgefüllte Röhrenlote -
Spécifications et méthodes d'essai - Partie 3: Méthodes Anforderungen und Prüfverfahren - Teil 3: Bestimmung der
d'essai à la balance de mouillage de l'efficacité des fils à Flussmittelwirkung von flussmittelgefüllten Röhrenloten mit
flux incorporé (ISO 12224-3:2003) der Benetzungswaage (ISO 12224-3:2003)
This European Standard was approved by CEN on 16 April 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12224-3:2003 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 12224-3:2003
EN ISO 12224-3:2003 (E)
CORRECTED 2003-07-02
Foreword
This document (EN ISO 12224-3:2003) has been prepared by Technical Committee ISO/TC 44
"Welding and allied processes" in collaboration with Technical Committee CEN/TC 121
"Welding", the secretariat of which is held by DS.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by November 2003, and conflicting national
standards shall be withdrawn at the latest by November 2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and
the United Kingdom.
Endorsement notice
The text of ISO 12224-3:2003 has been approved by CEN as EN ISO 12224-3:2003 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
2

---------------------- Page: 4 ----------------------

SIST EN ISO 12224-3:2003
EN ISO 12224-3:2003 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 9454-1 1990 Soft soldering fluxes - Classification EN 29454-1 1993
and requirements - Part 1:
Classification, labelling and packaging
ISO 9455-16 1998 Soft soldering fluxes - Test methods - EN ISO 9455-16 2001
Part 16: Flux efficacy tests, wetting
balance method
3

---------------------- Page: 5 ----------------------

SIST EN ISO 12224-3:2003

---------------------- Page: 6 ----------------------

SIST EN ISO 12224-3:2003


INTERNATIONAL ISO
STANDARD 12224-3
First edition
2003-05-01


Solder wire, solid and flux cored —
Specifications and test methods —
Part 3:
Wetting balance test method for flux
cored solder wire efficacy
Fils d'apport de brasage, pleins et à flux incorporé — Spécifications et
méthodes d'essai —

Partie 3: Méthode d'essai à la balance de mouillage de l'efficacité des
fils à flux incorporé




Reference number
ISO 12224-3:2003(E)
©
ISO 2003

---------------------- Page: 7 ----------------------

SIST EN ISO 12224-3:2003
ISO 12224-3:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2003 — All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 12224-3:2003
ISO 12224-3:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12224-3 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 12, Soldering and brazing materials.
ISO 12224 consists of the following parts, under the general title Solder wire, solid and flux cored —
Specifications and test methods:
 Part 1: Classification and performance requirements
 Part 2: Determination of flux content
 Part 3: Wetting balance test method for flux cored solder wire efficacy
© ISO 2003 — All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 12224-3:2003

------------
...