SIST CEN/TR 14633:2004
(Main)Welding - Working positions - Comparison of current international, European and US designations
Welding - Working positions - Comparison of current international, European and US designations
This Technical Report provides a comparison between the common working and welding positions shown in EN ISO 6947 and the joint orientations shown in ANSI/AWS A3.0, and ASME Boiler and pressure vessel code Section IX
Schweißen - Arbeitspositionen - Vergleich zwischen üblichen internationalen, europäischen und US-Benennungen
Dieser Technische Bericht enthält einen Vergleich zwischen den üblichen Arbeitspositionen, die in EN ISO 6947, ANSI/AWS A3.0 und ASME ?Boiler and Pressure Vessel, Code Section IX" aufgeführt sind.
Soudage - Positions de travail - Comparaison des désignations courantes internationales, européennes et US
Le présent Rapport Technique fournit une comparaison entre les positions de travail et de soudage courantes illustrées dans l'EN ISO 6947 et les orientations de joint illustrées dans l'ANSI/AWS A3.0 et dans la section IX du code ASME pour les chaudieres et appareils a pression.
Varjenje - Položaji pri varjenju - Primerjava veljavnih mednarodnih, evropskih in ameriških oznak
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST CEN/TR 14633:2004
01-junij-2004
Varjenje - Položaji pri varjenju - Primerjava veljavnih mednarodnih, evropskih in
ameriških oznak
Welding - Working positions - Comparison of current international, European and US
designations
Schweißen - Arbeitspositionen - Vergleich zwischen üblichen internationalen,
europäischen und US-Benennungen
Soudage - Positions de travail - Comparaison des désignations courantes
internationales, européennes et US
Ta slovenski standard je istoveten z: CEN/TR 14633:2003
ICS:
01.040.25 Izdelavna tehnika (Slovarji) Manufacturing engineering
(Vocabularies)
25.160.40 Varjeni spoji in vari Welded joints
SIST CEN/TR 14633:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST CEN/TR 14633:2004
---------------------- Page: 2 ----------------------
SIST CEN/TR 14633:2004
TECHNICAL REPORT
CEN/TR 14633
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
December 2003
ICS 01.040.25, 25.160.40
English version
Welding - Working positions - Comparison of current
international, European and US designations
Soudage - Positions de travail - Comparaison des Schweißen - Arbeitspositionen - Vergleich zwischen
désignations courantes internationales, européennes et US üblichen internationalen, europäischen und US-
Benennungen
This Technical Report was approved by CEN on 18 October 2003. It has been drawn up by the Technical Committee CEN/TC 121.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TR 14633:2003 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST CEN/TR 14633:2004
CEN/TR 14633:2003(E)
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Comparison of current international, European and US American designations for
working and welding positions .4
2
---------------------- Page: 4 ----------------------
SIST CEN/TR 14633:2004
CEN/TR 14633:2003 (E)
Foreword
This document (CEN/TR 14633:2003) has been prepared by Technical Committee CEN /TC 121, "Welding",
the secretariat of which is held by DS.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this CEN Technical Report: Austria, Belgium, Czech Republic, Denmark,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,
Norway, P
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.