SIST EN 13974:2003
(Main)Rigid plastics containers - Specification of tolerance for dimensions, weight and volume
Rigid plastics containers - Specification of tolerance for dimensions, weight and volume
This European Standard specifies tolerances for dimensions, mass and volume of plastic bottles and jars with a nominal capacity up to 5 l, of plastics canisters/jerricans with a nominal volume up to 20 l and for plastic pails up to 60 l.
NOTE Plastics bottles, jars, canisters and jerricans and pails are referred to as "containers" in this standard.
Formstabile Kunststoffbehälter - Grenzabmaße hinsichtlich Abmessungen, Masse und Volumen
Conteneurs en plastique rigide - Spécifications des tolérances sur les dimensions, le poids et le volume
La présente Norme européenne spécifie les tolérances sur les dimensions, la masse et le volume des bouteilles et bocaux en plastique d'une capacité nominale inférieure ou égale a 5 l, des bidons et jerricans en plastique d'un volume nominal inférieur ou égal a 20 l et des cuves en plastique d'un volume nominal inférieur ou égal a 60 l.
NOTE Dans la présente norme, les bouteilles, bocaux, bidons, jerricans et cuves en plastique sont désignés par le terme "conteneurs".
Toge plastične posode - Specifikacija odstopanj za mere, maso in prostornino
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SURVWRUQLQRFormstabile Kunststoffbehälter - Grenzabmaße hinsichtlich Abmessungen, Masse und VolumenConteneurs en plastique rigide - Spécifications des tolérances sur les dimensions, le poids et le volumeRigid plastics containers - Specification of tolerance for dimensions, weight and volume55.140Barrels. Drums. Canisters55.100Steklenice. Lonci. KozarciBottles. Pots. JarsICS:Ta slovenski standard je istoveten z:EN 13974:2002SIST EN 13974:2003en,fr,de01-julij-2003SIST EN 13974:2003SLOVENSKI
STANDARD
SIST EN 13974:2003
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13974October 2002ICS 55.100; 55.140English versionRigid plastics containers - Specification of tolerance fordimensions, weight and volumeConteneurs en plastique rigide - Spécifications destolérances sur les dimensions, le poids et le volumeFormstabile Kunststoffbehälter - Grenzabmaße hinsichtlichAbmessungen, Masse und VolumenThis European Standard was approved by CEN on 19 August 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13974:2002 ESIST EN 13974:2003
EN 13974:2002 (E)2ContentspageForeword.3Introduction.41Scope.52Terms and definitions.53Requirements.5SIST EN 13974:2003
EN 13974:2002 (E)3ForewordThis document EN 13974:2002 has been prepared by Technical Committee CEN/TC 261 "Packaging", thesecretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by April 2003, and conflicting national standards shall be withdrawn at the latest byApril 2003.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Swede
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.