SIST ETS 300 224 E1:2003

SLOVENSKI STANDARD
SIST ETS 300 224 E1:2003
01-december-2003
5DGLMVNDRSUHPDLQVLVWHPL5(6±6WRULWHYRVHEQHJDNOLFDQDNUDMXVDPHP±
7HKQLþQHLQIXQNFLMVNHNDUDNWHULVWLNH]DVLVWHPHRVHEQHJDNOLFDQDNUDMXVDPHP
YNOMXþQRVSUHVNXVQLPLPHWRGDPL
Radio Equipment and Systems (RES); On-site paging service; Technical and functional
characteristics for on-site paging systems, including test methods
Ta slovenski standard je istoveten z: ETS 300 224 Edition 1
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
33.070.20 Sistem za osebni klic Paging systems
SIST ETS 300 224 E1:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ETS 300 224 E1:2003

---------------------- Page: 2 ----------------------

SIST ETS 300 224 E1:2003
EUROPEAN ETS 300 224
TELECOMMUNICATION May 1994
STANDARD
Source: ETSI TC-RES Reference: DE/RES-8-02
ICS: 33.060
Radio, on-site paging
Key words:
Radio Equipment and Systems (RES);
On-site paging service
Technical and functional characteristics
for on-site paging systems,
including test methods
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
F-06921 Sophia Antipolis CEDEX - FRANCE
Postal address:
650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
Office address:
c=fr, a=atlas, p=etsi, s=secretariat - secretariat@etsi.fr
X.400: Internet:
Tel.: +33 92 94 42 00 - Fax: +33 93 65 47 16
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1994. All rights reserved.
New presentation - see History box

---------------------- Page: 3 ----------------------

SIST ETS 300 224 E1:2003
Page 2
ETS 300 224: May 1994
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Editing and Committee Support Dept." at the address shown on the title page.

---------------------- Page: 4 ----------------------

SIST ETS 300 224 E1:2003
Page 3
ETS 300 224: May 1994
Contents
Foreword.9
1 Scope . 11
2 Normative references . 11
3 Definitions and abbreviations. 12
3.1 Definitions. 12
3.2 Abbreviations. 12
4 Functional characteristics. 12
4.1 On-site paging system description. 12
4.2 On-site paging system basic services . 13
4.3 Description of additional functional characteristics. 13
5 General . 14
5.1 Presentation of radio paging equipment for testing purposes . 14
5.1.1 Choice of model for type approval . 15
5.1.2 Definition of alignment range . 15
5.1.3 Definition of the categories of the alignment range (AR1 and AR2). 15
5.1.4 Choice of frequencies . 15
5.1.5 Testing of equipment of category AR1 . 15
5.1.6 Testing of equipment of category AR2 . 15
5.1.7 Testing of equipment without an external 50 W antenna connector . 15
5.1.7.1 Equipment with a permanent internal 50 W RF connector. 15
5.1.7.2 Equipment with a temporary 50 W connector. 16
5.2 Mechanical and electrical design . 16
5.3 Marking (Equipment Identification). 16
5.4 Controls . 16
5.5 Transmitter shut-off facility. 16
5.6 Receiver mute or squelch circuit . 16
5.7 Declarations by the manufacturer . 16
5.8 Auxiliary test equipment . 16
5.9 Categories of emission. 17
5.10 Interpretation of the measurement results . 17
6 Test conditions, power sources and ambient temperatures. 17
6.1 Normal and extreme test conditions. 17
6.2 Normal operational test conditions. 17
6.2.1 Normal temperature and humidity . 17
6.2.2 Normal test power source. 17
6.3 Extreme test conditions . 18
6.3.1 Procedure for tests at extreme temperatures . 18
6.3.2 Extreme temperature limits . 18
6.3.3 Extreme test power source . 19
6.3.4 Test power source . 19
7 Electrical test conditions . 20
7.1 Normal test signals and test modulation . 20
7.1.1 Normal test signals for analogue speech . 20
7.1.2 Normal test signals for data . 20
7.2 Artificial load. 20
7.3 Test fixture for transmitters with an integral antenna . 20
7.4 Test site and general arrangements for the measurement of radiated fields. 21

---------------------- Page: 5 ----------------------

SIST ETS 300 224 E1:2003
Page 4
ETS 300 224: May 1994
7.5 Arrangements for test signals applied to the receiver input .21
8 Transmitter requirements .21
8.1 Frequency error .21
8.1.1 Definition.22
8.1.2 Method of measurement .22
8.1.3 Limits .22
8.2 Carrier power .23
8.2.1 Definition.23
8.2.2 Carrier power (conducted) .23
8.2.2.1 Method of measurement.23
8.2.2.2 Limits.23
8.2.3 Effective radiated power.23
8.2.3.1 Method of measurement.23
8.2.3.2 Limits.25
8.3 Adjacent channel power.25
8.3.1 Definition.25
8.3.2 Method of measurement .26
8.3.3 Limits .27
8.4 Frequency deviation.27
8.4.1 Definition.27
8.4.2 Method of measurement .27
8.4.3 Analogue signals within the audio bandwidth .28
8.4.4 Limits .28
8.4.5 Analogue signals above the audio bandwidth .28
8.5 Spurious radiations.29
8.5.1 Definition.29
8.5.2 Method of measurement .29
8.5.2.1 Method of measuring the spurious power level, using
measuring arrangement in figure 6 .30
8.5.2.2 Method of measuring the effective radiated spurious
power.30
8.5.3 Limits .31
8.6 Transmitter transient behaviour.31
8.6.1 Definition.31
8.6.1.1 Keying criteria when the transmitter output power is
switched on.32
8.6.1.2 Keying criteria when the transmitter output power is
switched off.32
8.6.2 Method of measurement .32
8.6.3 Limits .33
9 Receiver requirements.34
9.1 Pocket paging receivers.34
9.1.1 Spurious radiations .34
9.1.1.1 Definition.34
9.1.1.2 Method of measurement.34
9.1.1.3 Limits.34
9.2 Base station receivers .34
9.2.1 Measured sensitivity for analogue speech.34
9.2.1.1 Definition.34
9.2.1.2 Method of measurement.34
9.2.1.3 Limits.35
9.2.2 Measured sensitivity for messages .35
9.2.2.1 Definition.35
9.2.2.2 Method of measurement.35
9.2.2.3 Limits.35
9.2.3 Co-channel rejection for analogue speech.35
9.2.3.1 Definition.35
9.2.3.2 Method of measurement.36

---------------------- Page: 6 ----------------------

SIST ETS 300 224 E1:2003
Page 5
ETS 300 224: May 1994
9.2.3.3 Limits. 36
9.2.4 Co-channel rejection for messages. 36
9.2.4.1 Definition. 36
9.2.4.2 Method of measurement . 36
9.2.4.3 Limits. 37
9.2.5 Adjacent channel selectivity for analogue speech . 37
9.2.5.1 Definition. 37
9.2.5.2 Method of measurement . 37
9.2.5.3 Limits. 37
9.2.6 Adjacent channel selectivity for messages. 38
9.2.6.1 Definition. 38
9.2.6.2 Method of measurement . 38
9.2.6.3 Limits. 38
9.2.7 Spurious response immunity for analogue speech . 39
9.2.7.1 Definition. 39
9.2.7.2 Method of measurement . 39
9.2.7.3 Limit . 39
9.2.8 Spurious response immunity for messages. 39
9.2.8.1 Definition. 39
9.2.8.2 Method of measurement . 39
9.2.8.3 Limit . 40
9.2.9 Intermodulation immunity for analogue speech . 40
9.2.9.1 Definition. 40
9.2.9.2 Method of measurement . 40
9.2.9.3 Limit . 41
9.2.10 Intermodulation immunity for messages. 41
9.2.10.1 Definition. 41
9.2.10.2 Method of measurement . 41
9.2.10.3 Limit . 42
9.2.11 Blocking immunity or desensitisation for analogue speech. 42
9.2.11.1 Definition. 42
9.2.11.2 Method of measurement . 42
9.2.11.3 Limit . 43
9.2.12 Blocking immunity or desensitisation for messages . 43
9.2.12.1 Definition. 43
9.2.12.2 Method of measurement . 43
9.2.12.3 Limit . 44
9.2.13 Spurious radiations. 44
9.2.13.1 Definition. 44
9.2.13.2 Method of measurement . 44
9.2.13.2.1 Conducted spurious components . 44
9.2.13.2.2 Radiated spurious components. 44
9.2.13.3 Limits. 45
10 Inductive loop systems. 45
10.1 Additional definitions for inductive systems . 45
10.2 General. 45
10.2.1 Presentation of inductive loop paging equipment for testing purposes . 45
10.2.2 Choice of model for type testing. 45
10.2.3 Multi-carrier loop equipment. 45
10.2.3.1 Loop receivers . 45
10.2.3.2 Loop transmitters . 45
10.2.4 Single (modulated) carrier loop equipment. 46
10.2.4.1 Definition of alignment range. 46
10.2.4.2 Definition of the categories of the alignment range (AR1
and AR2) . 46
10.2.4.3 Choice of frequencies . 46
10.2.4.4 Testing of equipment of category AR1. 46
10.2.4.5 Testing of equipment of category AR2. 46
10.3 Loop transmitter requirements. 46

---------------------- Page: 7 ----------------------

SIST ETS 300 224 E1:2003
Page 6
ETS 300 224: May 1994
10.3.1 Transmitter carrier power.46
10.3.1.1 Definition.46
10.3.1.2 Measuring method .46
10.3.1.3 Limit .47
10.3.2 Range of operating frequencies .47
10.3.2.1 Limits.47
10.3.2.2 Frequency error. 47
10.3.2.2.1 Definition. 47
10.3.2.2.2 Measuring method.47
10.3.2.2.3 Limits .47
10.3.2.3 Modulation bandwidth.47
10.3.2.3.1 Definition.47
10.3.2.3.2 Measuring method.48
10.3.2.3.3 Limit.48
10.3.3 Spurious radiations .48
10.3.3.1 Definition.48
10.3.3.2 Measuring methods.48
10.3.3.2.1 Method of measuring the power level. 48
10.3.3.2.2 Method of measuring the field strength. 48
10.3.3.2.3 Method of measuring spurious
radiation above 25 MHz .49
10.3.3.3 Limits.49
10.4 Receiver requirements.49
10.4.1 Spurious radiations .49
10.4.1.1 Definition.49
10.4.1.2 Measuring method .49
10.4.1.3 Limits.50
11 Measurement uncertainty .50
11.1 Absolute measurement uncertainties: maximum values.50
Annex A (normative): Radiated measurements.51
A.1 Test sites and general arrangements for measurements involving the use of radiated fields.51
A.1.1 Outdoor test site.51
A.1.1.1 Standard position .51
A.1.2 Test antenna.52
A.1.3 Substitution antenna .52
A.1.4 Optional additional indoor site.52
A.2 Guidance on the use of radiation test sites .53
A.2.1 Measuring distance .53
A.2.2 Test antenna.54
A.2.3 Substitution antenna .54
A.2.4 Artificial antenna.54
A.2.5 Auxiliary cables .54
A.3 Further optional alternative indoor test site using an anechoic chamber.54
A.3.1 Example of the construction of a shielded anechoic chamber .54
A.3.2 Influence of parasitic reflections in anechoic chambers .55
A.3.3 Calibration of the shielded RF anechoic chamber.56
Annex B (informative): Detailed on-site description. 58
B.1 Characteristic features.58
B.2 On-site paging users.59
B.3 Spectrum efficiency .59

---------------------- Page: 8 ----------------------

SIST ETS 300 224 E1:2003
Page 7
ETS 300 224: May 1994
Annex C (normative): Support for pocket equipment. 60
Annex D (normative): Specification of power measuring receiver . 61
D.1 IF filter . 61
D.2 Attenuation indicator . 62
D.3 rms value indicator . 62
D.4 Oscillator and amplifier . 62
Annex E (normative): Spurious radiation limits for loop systems. 63
Annex F (informative): Bibliography. 64
History. 65

---------------------- Page: 9 ----------------------

SIST ETS 300 224 E1:2003
Page 8
ETS 300 224: May 1994
Blank page

---------------------- Page: 10 ----------------------

SIST ETS 300 224 E1:2003
Page 9
ETS 300 224: May 1994
Foreword
This European Telecommunication Standard (ETS) has been prepared by the Radio Equipment and
Systems (RES) Technical Committee of the European Telecommunications Standards Institute (ETSI).
This ETS is based mainly on CEPT Recommendation T/R 20-05 and ESPA publications 4.2.6 and 4.2.6.a.
In this ETS the operational aspects of the on-site paging service have been included.
In preparing this ETS, much attention has been given to assure a low interference probability, while at the
same time allowing a maximum flexibility and service to the end-user.
This ETS does not include performance characteristics that may be required by the user or requirements
for interfacing equipment.
The conditions for licensing as well as conditions for interfacing to PSTN are determined by the appropriate
authorities.
Every ETS prepared by ETSI is a voluntary standard. This ETS contains text concerning type approval of
the equipment to which it relates. This text should be considered only as guidance and does not make this
ETS mandatory in its status as a standard. However, this ETS can be referenced, wholly or in part, for
mandatory application by decisions of regulatory bodies.

---------------------- Page: 11 ----------------------

SIST ETS 300 224 E1:2003
Page 10
ETS 300 224: May 1994
Blank page

---------------------- Page: 12 ----------------------

SIST ETS 300 224 E1:2003
Page 11
ETS 300 224: May 1994
1 Scope
This ETS specifies the minimum performance characteristic and the related methods of measurement for
on-site paging transmitters and receivers. Although this ETS covers the general operational aspects of on-
site paging systems, it is restricted to the wireless (radio and loop) communications of the service. It is
assumed that the radio type of system will operate in the frequency range of 25 MHz to 470 MHz, and loop
systems below 150 kHz.
This ETS does not cover radiation below 25 MHz, except for the output of loop equipment.
Additional standards or specifications may be required for equipment intended to interface to the Public
Switched Telephone Network (PSTN).
This ETS may be used by accredited test laboratories for type testing of the equipment.
This ETS also contains instructions for the presentation of equipment for type testing purposes.
The types of equipment covered by this ETS are as follows:
- base station transmitters (radio and loop), with or without an external 50 W antenna connector;
- base station receivers, with a permanent 50 W connector;
- pocket unit (receiver, transceiver or transmitter), with or without an external 50 W antenna
connector.
Annex A: provides information concerning test sites and general arrangements for measurements
involving the use of radiated fields.
Annex B: provides information concerning the on-site paging service.
Annex C: provides normative information concerning measuring support for pocket equipment.
Annex D: contains normative specifications for adjacent channel power measuring receiver.
Annex E: is a graphic representation of the normative subclause 10.4.1.3 referring to the limits for
spurious radiations of loop receivers.
Annex F: contains a list of informative references.
2 Normative references
This ETS incorporates by dated or undated reference, provisions from other publications. These normative
references are cited at the appropriate places in the text and publications are listed hereafter. For dated
references, subsequent amendments to or revisions of any of these publications apply to this ETS only
when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies.
[1] ETR 027: "Radio Equipment and Systems (RES); Methods of measurement for
mobile radio equipment".
[2] ETR 028: "Radio Equipment and Systems (RES); Uncertainties
...