SIST EN 62211:2004

SLOVENSKI SIST EN 62211:2004

STANDARD
julij 2004
Inductive components - Reliability management (IEC 62211:2003)
ICS 29.100.10 Referenčna številka
SIST EN 62211:2004(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD EN 62211
NORME EUROPÉENNE
EUROPÄISCHE NORM January 2004

ICS 29.100.10


English version


Inductive components –
Reliability management
(IEC 62211:2003)


Composants inductifs –  Induktive Bauelemente -
Gestion de la fiabilité Zuverlässigkeitsmanagement
(CEI 62211:2003) (IEC 62211:2003)



This European Standard was approved by CENELEC on 2003-12-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 62211:2004 E

---------------------- Page: 2 ----------------------

EN 62211:2004 - 2 -
Foreword
The text of document 51/724/FDIS, future edition 1 of IEC 62211, prepared by IEC TC 51, Magnetic
components and ferrite materials, was submitted to the IEC-CENELEC parallel vote and was
approved by CENELEC as EN 62211 on 2003-12-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-09-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2006-12-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 62211:2003 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 62211:2004
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1) 2)
IEC 60068-2-1 - Environmental testing EN 60068-2-1 1993
Part 2: Tests - Tests A: Cold

1) 2)
IEC 60068-2-2 - Part 2: Tests - Test B: Dry heat EN 60068-2-2 1993

1) 2)
IEC 60068-2-6 - Part 2: Tests - Test Fc: Vibration EN 60068-2-6 1995
(sinusoidal)

1) 2)
IEC 60068-2-14 - Part 2: Tests - Test N: Change of EN 60068-2-14 1999
temperature

1) 2)
IEC 60068-2-20 - Part 2: Tests - Test T: Soldering HD 323.2.20 S3 1988

1) 2)
IEC 60068-2-27 - Part 2: Tests - Test Ea and guidance: EN 60068-2-27 1993
Shock

1) 2)
IEC 60068-2-29 - Part 2: Tests - Test Eb and guidance: EN 60068-2-29 1993
Bump

1) 2)
IEC 60068-2-30 - Part 2: Tests - Test Db and guidance: EN 60068-2-30 1999
Damp heat, cyclic (12 + 12 hour cycle)

1) 2)
IEC 60068-2-58 - Part 2-58: Tests - Test Td: Test EN 60068-2-58 1999
methods for solderability, resistance to
dissolution of metallization and to
soldering heat of surface mounting
devices (SMD)

1) 2)
IEC 60068-2-78 - Part 2-78: Tests - Test Cab: Damp heat, EN 60068-2-78 2001
steady state

IEC 60424 Series Ferrite cores - Guide on the limits of EN 60424 Series
surface irregularities

1) 2)
IEC 61007 (mod) - Transformers and inductors for use in EN 61007 1997
electronic and telecommunication
equipment - Measuring methods and
test procedures


1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 4 ----------------------

EN 62211:2004 - 4 -
Publication Year Title EN/HD Year
IEC 61248 Series Transformers and inductors for use in EN 61248 Series
electronic and telecommunication
equipment

---------------------- Page: 5 ----------------------

NORME CEI
INTERNATIONALE IEC
62211
INTERNATIONAL
Première édition
STANDARD
First edition
2003-10
Composants inductifs –
Gestion de la fiabilité
Inductive components –
Reliability management
© IEC 2003 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch  Web: www.iec.ch
CODE PRIX
N
Commission Electrotechnique Internationale PRICE CODE
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
Pour prix, voir catalogue en vigueur
For price, see current catalogue

---------------------- Page: 6 ----------------------

62211 © IEC:2003 – 3 –
CONTENTS
FOREWORD . 5
1 Scope . 9
2 Normative references. 9
3 Terms and definitions .11
4 Component families .13
5 Test samples .13
5.1 Classification by application.13
5.2 Numbering of samples and content of test report .15
5.3 Pre-treatment of test samples .15
5.3.1 Magnetic pre-treatment.15
5.3.2 Mechanical pre-treatment .15
5.3.3 Exposure to reflow temperature profile.15
6 Failure criteria .15
7 Test conditions and specification of the minimum requirements .23
8 Test sequence .29
9 Test evaluation .29
Table 1 – (General) mechanical failure criteria .19
Table 2 – Electrical failure criteria .21
Table 3 – Test conditions .25

---------------------- Page: 7 ----------------------

62211 © IEC:2003 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
INDUCTIVE COMPONENTS –
RELIABILITY MANAGEMENT
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62211 has been prepared by IEC technical committee 51:
Magnetic components and ferrite materials.
The text of this standard is based on the following documents:
FDIS Report on voting
51/724/FDIS 51/739/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 8 ----------------------

62211 © IEC:2003 – 7 –
The committee has decided that the contents of this publication will remain unchanged until 2005.
At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.

---------------------- Page: 9 ----------------------

62211 © IEC:2003 – 9 –
INDUCTIVE COMPONENTS –
RELIABILITY MANAGEMENT
1 Scope
This International Standard is applicable to inductive components (chokes and transformers)
based on magnetically soft materials. These are especially components based on laminated
iron sheets, iron powder materials (including alloys), as well as ferrites and amorphous or
crystalline metal band cores.
Winding assemblies means wire winding assemblies as well as multilayer and stacking
technologies of planar technology including the coil based on non-magnetic materials.
Discrete type components and the different types of surface-mountable inductive components
(SMD) are also considered in this standard.
The reliability of assemblies of inductive components based on several technologies such as
glued types, types with clamps (clips), impregnated (varnished) types as well as (vacuum)
potted types can also be checked with this standard.
The subsequent determinations can be applied either for the primary qualification of inductive
components or for all ways of requalification examinations (design, process, change of
production facility). They can also be applied for the monitoring of products out of actual
manufacturing processes.
This standard sets up a broad basis of electric and mechanical criteria of failure test
procedures.
If manufacturers advertise compliance with this standard in their data sheets, customers may
request data to demonstrate compliance to this standard. The customers may also request the
product to be in compliance to this standard by a recognised national institute.
Customers and manufacturers may elect to perform additional testing and acceptance criteria
different than those defined in this standard.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60068-2-1, Environmental testing – Part 2: Tests. Tests A: Cold
IEC 60068-2-2, Environmental testing – Part 2: Tests. Tests B: Dry heat
IEC 60068-2-6, Environmental testing – Part 2: Tests – Test Fc: Vibration (sinusoidal)
IEC 60068-2-14, Environmental testing – Part 2: Tests. Test N: Change of temperature
IEC 60068-2-20, Environmental testing – Part 2: Tests. Test T: Soldering

---------------------- Page: 10 ----------------------

62211 © IEC:2003 – 11 –
IEC 60068-2-27, Environmental testing – Part 2: Tests. Test Ea and guidance: Shock
IEC 60068-2-29, Environmental testing – Part 2: Tests. Test Eb and guidance: Bump
IEC 60068-2-30, Environmental testing – Part 2: Tests. Test Db and guidance: Damp heat,
cyclic (12 + 12-hour cycle)
IEC 60068-2-58, Environmental testing – Part 2-58: Tests – Test Td – Test methods for
solderability, resistance to dissolution of metallization and soldering heat of surface mounting
devices (SMD)
IEC 60068-2-78, Environmental testing – Part 2-78: Tests – Test Cab: Damp heat, steady
state
IEC 60424 (all parts), Ferrite cores – Guide on the limits of surface irregularities
IEC 61007,Transformers and inductors for use in electronic and telecommunication equipment
– Measuring methods and test procedures
IEC 61248 (all parts),Transformers and inductors for use in electronic and telecommunication
equipment
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
reliability of inductive components
component level reliability of the inductive component in the customers’ electrical circuit
application
3.2
component level reliability tests
sequence of tests performed on an individual component, each specific test being designed to
represent conditions under which the component is expected to operate in end applications
NOTE Categories of test levels are organised to be consistent for typical applications.
3.3
system level reliability tests
sequence of tests performed on a collection of components as arranged in a specific end
application under working conditions
3.4
component family
group of components characterised by the same common features, for example the same
magnetic base material, the same core size and the same winding type

---------------------- Page: 11 ----------------------

62211 © IEC:2003 – 13 –
4 Component families
In a similar way to the qualification rules contained in IEC 61248, reliability tests can be
performed on typical samples representing families of inductive components.
A family of inductive components is defined on the basis of:
– the same application class as specified in the IEC 61248 series;
– the same magnetic base material group (for example ferrite, metal powder, etc.);
– the same core shape (for example E-type, RM, ring core, etc.);
– the same winding type (for example wire-wound, multilayer, stack, etc.);
– the same termination configuration (PTH, SMD etc.);
– comparable accessories
...