SIST EN ISO 1513:2011

SLOVENSKI STANDARD
SIST EN ISO 1513:2011
01-november-2011
1DGRPHãþD
SIST EN ISO 1513:1997
Barve in laki - Pregled in priprava vzorcev za preskušanje (ISO 1513:2010)
Paints and varnishes - Examination and preparation of test samples (ISO 1513:2010)
Beschichtungssstoffe - Prüfung und Vorbereitung von Proben (ISO 1513:2010)
Peintures et vernis - Examen et préparation des échantillons pour essai (ISO 1513:2010)
Ta slovenski standard je istoveten z: EN ISO 1513:2010
ICS:
87.040 Barve in laki Paints and varnishes
SIST EN ISO 1513:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 1513:2011

---------------------- Page: 2 ----------------------

SIST EN ISO 1513:2011


EUROPEAN STANDARD
EN ISO 1513

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2010
ICS 87.040 Supersedes EN ISO 1513:1994
English Version
Paints and varnishes - Examination and preparation of test
samples (ISO 1513:2010)
Peintures et vernis - Examen et préparation des Beschichtungssstoffe - Prüfung und Vorbereitung von
échantillons pour essai (ISO 1513:2010) Proben (ISO 1513:2010)
This European Standard was approved by CEN on 15 April 2010.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1513:2010: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 1513:2011
EN ISO 1513:2010 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 1513:2011
EN ISO 1513:2010 (E)
Foreword
This document (EN ISO 1513:2010) has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2010, and conflicting national standards shall be withdrawn
at the latest by November 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1513:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 1513:2010 has been approved by CEN as a EN ISO 1513:2010 without any modification.


3

---------------------- Page: 5 ----------------------

SIST EN ISO 1513:2011

---------------------- Page: 6 ----------------------

SIST EN ISO 1513:2011

INTERNATIONAL ISO
STANDARD 1513
Fourth edition
2010-05-01


Paints and varnishes — Examination and
preparation of test samples
Peintures et vernis — Examen et préparation des échantillons pour
essai




Reference number
ISO 1513:2010(E)
©
ISO 2010

---------------------- Page: 7 ----------------------

SIST EN ISO 1513:2011
ISO 1513:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2010 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 1513:2011
ISO 1513:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 1513 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 9,
General test methods for paints and varnishes.
This fourth edition cancels and replaces the third edition (ISO 1513:1992), which has been technically revised.
It also incorporates the Technical Corrigendum ISO 1513:1992/Cor.1:1994. The main technical changes are:
a) the title has been changed to “Examination and preparation of test samples”;
b) the normative references have been updated;
c) a definitions clause with definitions of thixotropy and homogenization has been added;
d) the examination and mixing procedures for liquid and paste-like products have been combined into a
single clause (Clause 5);
e) the type of sieve to be used for straining the sample is no longer specified.
© ISO 2010 – All rights reserved iii

---------------------- Page: 9 ----------------
...