SIST EN 4318:2007

SLOVENSKI STANDARD
SIST EN 4318:2007
01-november-2007
$HURQDYWLND=OLWLQD)(3$;1L&U7L0R9RGSRUQDSURWLYURþLQL3DOLFH
LQSURILOL'H PP5P! 03DREGHODQLYUD]WRSLQLLQXWUMHQL
Aerospace series - Heat resisting alloy FE-PA2601 (X6NiCrTiMoV26-15) - Solution
treated and precipitation treated, bar and section De <= 100 mm, Rm >= 960 MPa
Luft- und Raumfahrt - Hochwarmfeste Legierung FE-PA2601 (X6NiCrTiMoV26-15) -
Lösungsgeglüht und ausgehärtet, Stangen und Profile De <= 100 mm, Rm >= 960 MPa
Série aérospatiale - Alliage résistant a chaud FE-PA2601 (X6NiCrTiMoV26-15) - Mis en
solution et précipité, barres et profilés De <= 100 mm, Rm >= 960 MPa
Ta slovenski standard je istoveten z: EN 4318:2007
ICS:
49.025.05 Železove zlitine na splošno Ferrous alloys in general
SIST EN 4318:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 4318

NORME EUROPÉENNE

EUROPÄISCHE NORM
August 2007
ICS 49.025.05
English Version
Aerospace series - Heat resisting alloy FE-PA2601
(X6NiCrTiMoV26-15) - Solution treated and precipitation treated,
bar and section De ≤ 100 mm, Rm ≥ 960 MPa
Série aérospatiale - Alliage résistant à chaud FE-PA2601 Luft- und Raumfahrt - Hochwarmfeste Legierung FE-
(X6NiCrTiMoV26-15) - Mis en solution et précipité, barres PA2601 (X6NiCrTiMoV26-15) - Lösungsgeglüht und
et profilés De ≤ 100 mm, Rm ≥ 960 MPa ausgehärtet, Stangen und Profile De ≤ 100 mm, Rm ≥ 960
MPa
This European Standard was approved by CEN on 15 February 2007.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4318:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 4318:2007 (E)
Contents Page
Introduction .4
1 Scope.4
2 Normative references.4



2

---------------------- Page: 3 ----------------------

EN 4318:2007 (E)
Foreword
This document (EN 4318:2007) has been prepared by the Aerospace and Defence Industries Association of
Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2008, and conflicting national standards shall be withdrawn
at the latest by February 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
Accordi
...