Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheets 406 to 408: Glass textile sleeving with PVC coating

Gives the requirements for E-type glass sleeving using either braided or knitted construction with a continuous flexible coating based on polyvinyl chloride (PVC) or its copolymers or blends thereof. These sleevings have been found suitable up to temperatures of 105 °C.
The sleeving is normally available with internal diameters between 0,3 mm and 25 mm and is normally supplied in the following colours : black, white, red, yellow, blue, brown, green, grey, orange, pink and green/yellow.
Sizes or colours other than those specifically listed in this standard may be available as custom items.  These items shall be considered to comply with this standard if they comply with the other property requirements listed in Tables 2 and 5, except for dimensions, and, where applicable, in Table 3.
Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.
This edition has been aligned to reflect the changes made to the 2nd edition of IEC 60684-2, Test methods, and standardizes on a 100 mm long electrode for breakdown voltage.

Isolierschläuche -- Teil 3: Anforderungen für einzelne Schlauchtypen -- Blätter 406 bis 408: Glasfilament-Textilschläuche mit Beschichtung auf PVC-Basis

Gaines isolantes souples -- Partie 3: Spécifications pour types particuliers de gaines -- Feuilles 406 à 408: Gaines en fibre de verre tissées, avec revêtement PVC

Donne les prescriptions relatives aux gaines tressées ou tricotées en verre de type E avec un revêtement continu souple en polychlorure de vinyle (PVC) ou en l'un de ses copolymères ou leurs mélanges. Ces produits sont adaptés pour des températures allant jusqu'à 105 °C.
Les gaines sont normalement disponibles pour des diamètres intérieurs compris entre 0,3 mm et 25 mm et sont normalement fournies dans les coloris suivants: noir, blanc, rouge, jaune, bleu, brun, vert, gris, orange, rose et vert/jaune.
D'autres dimensions et d'autres couleurs que celles spécifiquement indiquées dans cette norme peuvent être disponibles comme articles spéciaux. Ces articles doivent être considérés comme satisfaisant à cette norme s'ils satisfont aux autres caractéristiques indiquées dans les Tableaux 2 et 5, en excluant les dimensions, et, quand cela s'applique, dans le Tableau 3.
Les matériaux conformes à cette spécification satisfont à des niveaux établis de performance. Cependant il convient que le choix d'un matériau par un utilisateur pour une application spécifique soit fondé sur les exigences réelles nécessaires pour une performance adéquate de cette application, et non fondé sur cette seule spécification.
Cette édition a été alignée afin de tenir compte des changements effectués dans la deuxième édition de la CEI 60684-2, Méthodes d'essai, et normalise l'utilisation d'une électrode d'une longueur de 100 mm pour une tension de claquage.

Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - Listi od 406 do 408: Steklo tekstilne cevi s prevleko iz PVC (IEC 60684-3-406 to 408:2003)

General Information

Status
Published
Publication Date
31-Aug-2004
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Sep-2004
Due Date
01-Sep-2004
Completion Date
01-Sep-2004

Relations

Buy Standard

Standard
EN 60684-3-406 to 408:2004
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI SIST EN 60684-3-406 to
408:2004

STANDARD
september 2004
Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - Listi od
406 do 408: Steklo tekstilne cevi s prevleko iz PVC (IEC 60684-3-406 to
408:2003)
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving -
Sheets 406 to 408: Glass textile sleeving with PVC coating (IEC 60684-3-406 to
408:2003)
ICS 29.035.30 Referenčna številka
SIST EN 60684-3-406 to 408:2004(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD EN 60684-3-406 to 408
NORME EUROPÉENNE
EUROPÄISCHE NORM October 2003

ICS 29.035.20 Supersedes HD 523.3.406 to 408 S1:1990


English version


Flexible insulating sleeving
Part 3: Specifications for individual types of sleeving
Sheets 406 to 408: Glass textile sleeving with PVC coating
(IEC 60684-3-406 to 408:2003)


Gaines isolantes souples Isolierschläuche
Partie 3: Spécifications Teil 3: Anforderungen
pour types particuliers de gaines für einzelne Schlauchtypen
Feuilles 406 à 408: Gaines en fibre Blätter 406 bis 408: Glasfilament-
de verre tissées, avec revêtement PVC Textilschläuche mit Beschichtung
(CEI 60684-3-406 à 408:2003) auf PVC-Basis
(IEC 60684-3-406 bis 408:2003)






This European Standard was approved by CENELEC on 2003-10-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60684-3-406 to 408:2003 E

---------------------- Page: 2 ----------------------

EN 60684-3-406 to 408:2003 - 2 -
Foreword

The text of document 15C/1512/FDIS, future edition 2 of IEC 60684-3-406 to 408, prepared by SC 15C,
Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote
and was approved by CENELEC as EN 60684-3-406 to 408 on 2003-10-01.

This European Standard supersedes HD 523.3.406 to 408 S1:1990.

The following dates were fixed:

– latest date by which the EN has to be implemented
 at national level by publication of an identical
 national standard or by endorsement (dop) 2004-07-01

– latest date by which the national standards conflicting
 with the EN have to be withdrawn (dow) 2006-10-01

Annexes designated "normative" are part of the body of the standard.
In this standard, annex ZA is normative.
Annex ZA has been added by CENELEC.
__________

Endorsement notice

The text of the International Standard IEC 60684-3-406 to 408:2003 was approved by CENELEC as a
European Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 60684-3-406 to 408:2003
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60068-2-10 1988 Environmental testing HD 323.2.10 S3 1988
Part 2: Tests - Test J and guidance:
Mould growth

IEC 60684-1 2003 Flexible insulating sleeving EN 60684-1 2003
Part 1: Definitions and general
requirements

IEC 60684-2 1997 Part 2: Methods of test EN 60684-2 1997

IEC 60757 1983 Code for designation of colours HD 457 S1 1985

---------------------- Page: 4 ----------------------

NORME
CEI
INTERNATIONALE IEC
60684-3-406
INTERNATIONAL
à/to 408
STANDARD
Deuxième édition
Second edition
2003-07
Gaines isolantes souples –
Partie 3:
Spécifications pour types particuliers de gaines –
Feuilles 406 à 408: Gaines en fibre de verre
tissées, avec revêtement PVC
Flexible insulating sleeving –
Part 3:
Specifications for individual types of sleeving –
Sheets 406 to 408: Glass textile sleeving
with PVC coating
© IEC 2003 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch  Web: www.iec.ch
CODE PRIX
L
Commission Electrotechnique Internationale PRICE CODE
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
Pour prix, voir catalogue en vigueur
For price, see current catalogue

---------------------- Page: 5 ----------------------

60684-3-406 to 408 © IEC:2003 – 3 –
CONTENTS
FOREWORD . 5
INTRODUCTION .9
1 Scope .11
2 Normative references.11
3 Designation .13
4 Requirements .13
4.1 Standard requirements .13
4.2 Special requirements .13
5 Sleeving conformance.13
Table 1 – Dimensional requirements .15
Table 2 – Standard requirements .17
Table 3 – Special requirements .19
Table 4 – Mandrel diameters for bending tests .19
Table 5 – Requirements for breakdown voltage.21

---------------------- Page: 6 ----------------------

60684-3-406 to 408 © IEC:2003 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
FLEXIBLE INSULATING SLEEVING –
Part 3: Specifications for individual types of sleeving –
Sheets 406 to 408: Glass textile sleeving with PVC coating
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to
technical committees; any IEC National Committee interested in the subject dealt with may participate in this
preparatory work. International, governmental and non-governmental organizations liaising with the IEC also
participate in this preparation. IEC collaborates closely with the International Organization for Standardization
(ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.