SIST ISO 11084-2:2008

SLOVENSKI STANDARD
SIST ISO 11084-2:2008
01-januar-2008
*UDILþQDWHKQRORJLMD5HJLVWUVNLVLVWHPL]DIRWRJUDIVNHPDWHULDOHIROLMHLQSDSLU
GHO6LVWHPL]DL]GHODYRWLVNRYQLKIRUP
Graphic technology - Register systems for photographic materials, foils and paper - Part
2: Register pin systems for plate making
Ta slovenski standard je istoveten z:
ICS:
37.100.20 0DWHULDOL]DJUDILþQRWHKQLNR Materials for graphic
technology
SIST ISO 11084-2:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

INTERNATIONAL ISO
STANDARD 11084-2
First edition
2006-06-15


Graphic technology — Register systems
for photographic materials, foils
and paper —
Part 2:
Register pin systems for plate making
Technologie graphique — Systèmes de positionnement pour matériaux
photographiques, feuilles et papier —
Partie 2: Systèmes de positionnement à broche pour clichage





Reference number
ISO 11084-2:2006(E)
©
ISO 2006

---------------------- Page: 2 ----------------------

ISO 11084-2:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2006 – All rights reserved

---------------------- Page: 3 ----------------------

ISO 11084-2:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11084-2 was prepared by Technical Committee ISO/TC 130, Graphic technology.
ISO 11084 consists of the following parts, under the general title Graphic technology — Register systems for
photographic materials, foils and paper:
⎯ Part 1: Three-pin systems
⎯ Part 2: Register pin systems for plate making
© ISO 2006 – All rights reserved iii

---------------------- Page: 4 ----------------------

ISO 11084-2:2006(E)
Introduction
The standardization of register system in graphic technology achieves greater economy and efficiency by
reducing the variety of register pin systems required by prepress operations. Such an approach helps to
reduce the number of errors, and hence reduce the use of consumable materials. Part 1 of this International
Standard specifies the pin configuration for a three-pin register system by defining the shapes, dimensions
and positions for the pins a
...