iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN ISO 8970:2010

(Main)

Timber structures - Testing of joints made with mechanical fasteners Requirements for wood density (ISO 8970:2010)

Timber structures - Testing of joints made with mechanical fasteners Requirements for wood density (ISO 8970:2010)

This International Standard specifies a method, based on density, for the selection of pieces of wood used in determining the strength and stiffness properties of connections made with mechanical fasteners. It is assumed the wood density is normally distributed and that any deviations are reported. This International Standard is applicable only to specimens of wood.

Holzbauwerke - Prüfung von Verbindungen mit mechanischen Verbindungsmitteln - Anforderungen an die Rohdichte des Holzes (ISO 8970:2010)

Diese Internationale Norm legt ein Verfahren fest, bei dem Holzstücke zur Bestimmung der Festigkeits- und Steifigkeitseigenschaften von Verbindungen mit mechanischen Verbindungsmitteln auf der Grundlage der Rohdichte ausgewählt werden. Es wird vorausgesetzt, dass die Rohdichte des Holzes normalverteilt ist und dass alle Abweichungen bekannt sind. Diese Internationale Norm bezieht sich nur auf Probekörper aus Holz.
ANMERKUNG Es wird besonders darauf hingewiesen, dass die Rohdichte des Holzes nur eine der Eigenschaften ist, die die Tragfähigkeit einer Verbindung beeinflussen kann. Andere diesbezügliche Eigenschaften sind z. B. Jahresring-breite, Faserverlauf, Belastbarkeit und Härte.

Structures en bois - Essai des assemblages réalisés par organes mécaniques - Exigences concernant la masse volumique du bois (ISO 8970:2010)

L'ISO 8970:2010 spécifie une méthode de prélèvement, basée sur la masse volumique, des éprouvettes en bois utilisées pour déterminer les propriétés de résistance et de rigidité des assemblages réalisés par des organes mécaniques.

Lesene konstrukcije - Preskušanje zvez s kovinskimi veznimi sredstvi - Zahteve za gostoto lesa (ISO 8970:2010)

Ta mednarodni standard določa metodo, osnovano na gostoti, za izbor kosov lesa, uporabljenih pri določevanju lastnostih trdnosti in togosti, pri spojih z kovinskimi veznimi sredstvi. Predvideva se, da je gostota lesa normalno porazdeljena in da so vsa odstopanja priglašena. Ta mednarodni standard velja samo vzorce lesa.

General Information

Status
Withdrawn
Public Enquiry End Date
19-Jun-2009
Publication Date
22-Jul-2010
Withdrawal Date
16-Jun-2020
ICS
91.080.20 - Timber structures
Technical Committee
KON.005 - Timber structures
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
17-Jun-2020
Due Date
10-Jul-2020
Completion Date
17-Jun-2020
Directive
89/106/EEC - Construction products
Ref Project
EN ISO 8970:2010 - Timber structures - Testing of joints made with mechanical fasteners - Requirements for wood density (ISO 8970:2010)

Relations

Replaced By
SIST EN ISO 8970:2020 - Timber structures - Testing of joints made with mechanical fasteners - Requirements for timber density (ISO 8970:2020)
Effective Date
01-Jul-2020
Replaced By
SIST EN ISO 8970:2020 - Timber structures - Testing of joints made with mechanical fasteners - Requirements for timber density (ISO 8970:2020)
Effective Date
08-Jun-2022
Replaces
SIST EN 28970:1997 - Timber structures - Testing of joints made with mechanical fasteners - Requirements for wood density (ISO 8970:1989)
Effective Date
01-Sep-2010

Buy Standard

EN ISO 8970:2010EN ISO 8970:2010
PreviousNext
Standard
EN ISO 8970:2010
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Lesene konstrukcije - Preskušanje zvez s kovinskimi veznimi sredstvi - Zahteve za gostoto lesa (ISO 8970:2010)Holzbauwerke - Prüfung von Verbindungen mit mechanischen Verbindungsmitteln - Anforderungen an die Rohdichte des Holzes (ISO 8970:2010)Structures en bois - Essai des assemblages réalisés par organes mécaniques - Exigences concernant la masse volumique du bois (ISO 8970:2010)Timber structures - Testing of joints made with mechanical fasteners
Requirements for wood density (ISO 8970:2010)91.080.20Lesene konstrukcijeTimber structuresICS:Ta slovenski standard je istoveten z:EN ISO 8970:2010SIST EN ISO 8970:2010en,fr01-september-2010SIST EN ISO 8970:2010SLOVENSKI
STANDARDSIST EN 28970:19971DGRPHãþD



SIST EN ISO 8970:2010



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 8970
June 2010 ICS 91.080.20 Supersedes EN 28970:1991English Version
Timber structures - Testing of joints made with mechanical fasteners - Requirements for wood density (ISO 8970:2010)
Structures en bois - Essai des assemblages réalisés par organes mécaniques - Exigences concernant la masse volumique du bois (ISO 8970:2010)
Holzbauwerke - Prüfung von mechanischen Verbindungen -Anforderungen an die Rohdichte des Holzes (ISO 8970:2010) This European Standard was approved by CEN on 12 June 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 8970:2010: ESIST EN ISO 8970:2010



EN ISO 8970:2010 (E) 2 Contents Page Foreword .3 SIST EN ISO 8970:2010



EN ISO 8970:2010 (E) 3 Foreword This document (EN ISO 8970:2010) has been prepared by Technical Committee ISO/TC 165 “Timber structures” in collaboration with Technical Committee CEN/TC 124 “Timber structures” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn at the latest by December 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 28970:1991. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 8970:2010 has been approved by CEN as a EN ISO 8970:2010 without any modification. SIST EN ISO 8970:2010



SIST EN ISO 8970:2010



Reference numberISO 8970:2010(E)© ISO 2010
INTERNATIONAL STANDARD ISO8970Second edition2010-06-15Timber structures — Testing of joints made with mechanical fasteners — Requirements for wood density Structures en bois — Essai des assemblages réalisés par organes mécaniques — Exigences concernant la masse volumique du bois
SIST EN ISO 8970:2010



ISO 8970:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2010 – All rights reserved
SIST EN ISO 8970:2010



ISO 8970:2010(E) © ISO 2010 – All rights
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 14081-2:2018+A1:2022(Main)
Timber structures - Strength graded structural timber with rectangular cross section - Part 2: Machine grading; additional requirements for type testing
EN 14081-2:2018+A1:2022

This document specifies requirements, additional to those of EN 14081-1, for type testing of machine graded structural timber with rectangular cross-sections shaped by sawing, planning or other methods, and having deviations from the target sizes corresponding to EN 336. This includes requirements for strength grading machines.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 384:2016+A2:2022(Main)
Structural timber - Determination of characteristic values of mechanical properties and density
EN 384:2016+A2:2022

This European Standard gives a method for determining characteristic values of mechanical properties and density, for defined populations of visual grades and/or strength classes of machine graded structural timber. Additionally it covers the stages of sampling, testing, analysis and presentation of the data.
The standard provides methods to derive strength, stiffness and density properties for structural timber from tests with defect-free specimen.
The values determined in accordance with this standard for mechanical properties and density are suitable for assigning grades and species to the strength classes of EN 338.
NOTE 1   For assigning grades and species to the strength classes in EN 338 only three properties, i.e. bending or tension strength, modulus of elasticity parallel to grain in bending or tension and density need to be determined from test data, other properties can be calculated according to Table 2.
NOTE 2   EN 1912 gives examples of established visual grades assigned to strength classes.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14592:2022(Main)
Timber structures - Dowel-type fasteners - Requirements
EN 14592:2022

This draft European Standard specifies the requirements for the following types of dowel-type fasteners: nails, staples, screws, dowels, and bolts with nuts.
Only dowel-type fasteners for structural use in load bearing timber structures, and manufactured from steel, are covered by this European Standard. In addition, this draft European Standard covers also the use of screws:
-   to fix roof or cladding elements to the timber structure, with or without insulation layers;
and
-   as reinforcement inserted in timber or in a glue laminated timber element to improve its resistance to compression perpendicular to the grain.
This draft European Standard specifies also the assessment and verification of constancy of performance (AVCP) procedures and includes requirements for marking of these products.
This draft European Standard covers dowel-type fasteners that may be coated for the following purposes:
-   corrosion protection;
-   lubrication (to facilitate insertion);
-   withdrawal enhancement and/or collation for staples (adhesive and/or resin coatings).
This draft European Standard does not cover fasteners treated with fire retardants to improve their fire performance, nor does it cover glued-in rods.

  • Standard
    78 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14081-3:2022(Main)
Timber structures - Strength graded structural timber with rectangular cross section - Part 3: Machine grading; additional requirements for factory production control
EN 14081-3:2022

This document specifies requirements additional to those given in EN 14081-1 for factory production control of machine graded structural timber with rectangular cross-sections shaped by sawing, planing or other methods, and having deviations from the target sizes corresponding to EN 336.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16351:2021(Main)
Timber structures - Cross laminated timber - Requirements
EN 16351:2021

This document sets out requirements regarding the performance of characteristics of the following types of cross laminated timber to be used in buildings and bridges:
-   type 1: Straight or curved cross laminated timber comprising only timber layers but no large finger joints;
-   type 2: Straight cross laminated timber comprising only timber layers and large finger joints;
-   type 3: Straight cross laminated timber comprising timber and wood-based panel layers but no large finger joints.
It also lays down procedures for assessment and verification of constancy of performance (AVPC) of characteristics and specifies marking and labelling of cross laminated timber.
This document covers cross laminated timber of all three types of cross laminated timber:
-   manufactured according to this standard, which sets up provisions for:
-   boundary conditions during manufacture of cross laminated timber;
-   moisture content and temperature of timber to be bonded;
-   production of finger joints and bonds between layers;
-   to be used in service class 1 or 2 according to EN 1995 1 1;
-   made of coniferous species and poplar listed in this standard;
-   which may be made of layers made of different species having similar properties;
-   bonded with phenolic or aminoplastic or moisture curing one-component polyurethane or emulsion polymer isocyanate adhesives of adhesive type I according to the respective standard;
-   built up of at least three orthogonally bonded layers (at least two of them timber layers);
-   which may have, depending on the number of layers, adjacent layers bonded parallel to the grain;
-   made of timber layers which are made of strength graded timber according to EN 14081 1;
-   made of timber layers having nominal thicknesses between 6 mm (including) and 60 mm (including) depending on the layup;
-   made of timber layers
-   which may comprise non-structural edge bonds; and
-   have a mean gap width of less than or equal to 0,6 mm and a 90th percentile of the gap width of 2 mm;
-   having nominal overall thicknesses up to 500 mm.
Additional provisions of this document apply for straight cross laminated timber comprising only timber layers and comprising large finger joints (type 2):
-   made from cross laminated timber pieces having the same cross-section and layup;
-   made from cross laminated timber pieces having nominal cross-sectional thicknesses from 51 mm (including) up to 345 mm (including) and nominal minimum thicknesses of the outer layers not less than 17 mm (including).
-   made from cross laminated timber pieces solely comprising timber layers;
-   made from plane cross laminated timber pieces;
-   with parallel x-axes of the jointed components;
-   with finger joints having a finger length of at least 45 mm and fingers which are visible at the two narrow sides of the components;
-   bonded with phenolic or aminoplastic or moisture curing one-component polyurethane adhesives of adhesive type I according to the respective standard.
Additional provisions of this document apply for straight cross laminated timber comprising timber and wood-based panel layers but no large finger joints (type 3):
-   made of structural wood-based panels specified in this European standard;
-   made of one panel per layer and;
-   having thicknesses between 6 mm (including) and 45 mm (including);
This document applies to cross laminated timber untreated or treated against biological attack.
This document  does not cover:
-   cross laminated timber treated with fire retardants;
-   cross laminated timber which is produced from re-used timber or wood-based panels comprising re-used timber.

  • Standard
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    92 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 8970:2020(Main)
Timber structures - Testing of joints made with mechanical fasteners - Requirements for timber density (ISO 8970:2020)
EN ISO 8970:2020

This document specifies a method based on density, for the selection of pieces of wood used in
determining the strength and stiffness properties of joints between members of structural timber
made with mechanical fasteners. It is intended to be used in conjunction with a test standard specifying
a test method.
It is assumed that the wood pieces are conditioned to the relevant conditions, that the wood density is
normally distributed and that any deviations are reported.
This document is applicable only to specimens of structural timber.
NOTE It is emphasized that the wood density is only one of the properties that can influence the strength of
a joint. Other relevant properties are, for example, growth-ring size and orientation, toughness and hardness.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14081-1:2016+A1:2019(Main)
Timber structures - Strength graded structural timber with rectangular cross section - Part 1: General requirements
EN 14081-1:2016+A1:2019

This European Standard specifies requirements for strength graded structural timber with rectangular cross-sections either visual or machine graded, shaped by sawing, planning or other methods and with cross-sectional dimensions complying with EN 336 (referred to as structural timber in the following clauses).
This European Standard includes provisions for test methods, Assessment and Verification of Constancy of Performance and marking of structural timber.
NOTE 1   For machine strength graded timber additional provisions for type testing (TT) are given in EN 14081-2 and for factory production control (FPC) in EN 14081-3.
NOTE 2   An acceptance procedure for verification of a lot is given in EN 14358 which may be used for a delivery of structural timber.
This European Standard identifies characteristics for which limits have to be given in visual grading standards.
This European Standard covers structural timber, untreated or treated against biological attack.
This European Standard does not cover:
-   timber treated by fire retardant products to improve its fire performance;
-   thermally and/or chemically modified timber;
-   structural finger jointed timber.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16929:2019(Main)
Test methods - Timber floors - Determination of vibration properties
EN 16929:2018

This Europen Standard specifies test methods for the determination of the fundamental frequency, damping, unit point load deflection and acceleration of timber or wood based composite beams and flooring systems.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14358:2016(Main)
Timber structures - Calculation and verification of characteristic values
EN 14358:2016

This document specifies methods for the determination of characteristic 5-percentile strength and density values as well as mean values for stiffness from test results for solid wood, fasteners, and wood-based products in the frame of initial type testing.
This document also gives methods for checking strength, density or stiffness properties in the frame of factory production control by variables. Sampling is not covered by this document, but reference is made to the relevant product standards.
In addition to this standard, specific requirements related to the product are given in separate standards.
NOTE   For example, in the case of solid timber, specific correction factors for calculation of characteristic values are given in EN 384.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16784:2016(Main)
Timber structures - Test methods - Determination of the long term behaviour of coated and uncoated dowel-type fasteners
EN 16784:2016

This European Standard specifies the test methods for determining the long term behaviour of coated and uncoated dowel-type fasteners in load bearing timber structures (nails, staples, screws, dowels and bolts with nuts).

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day