Plastics hoses - Textile-reinforced types for compressed-air applications - Specification (ISO 5774:2016)

This International Standard specifies the requirements for four types of flexible thermoplastic hose,
textile reinforced, for compressed-air applications in the temperature range from −10 °C to +60 °C.
The four types are classified as light service for a maximum working pressure of 7 bar at 23 °C and
4,5 bar at 60 °C, medium service for a maximum working pressure of 10 bar at 23 °C and 6,5 bar at
60 °C, heavy service for a maximum working pressure of 16 bar at 23 °C and 11 bar at 60 °C, and heavy
service for use in mining for a maximum working pressure of 25 bar at 23 °C and 13 bar at 60 °C.

Kunststoffschläuche - Textilverstärkte Typen für Druckluftanwendungen - Anforderung (ISO 5774:2016)

Diese Internationale Norm legt die Anforderungen an vier Typen von flexiblen thermoplastischen Schläuchen mit Textileinlage für Druckluftanwendungen in einem Temperaturbereich von -10 °C bis +60 °C fest.
Die vier Typen werden eingestuft in einen leichten Einsatzbereich mit einem maximalen Betriebsdruck von 7 bar bei 23 °C und 4,5 bar bei 60 °C, einen mittleren Einsatzbereich mit einem maximalen Betriebsdruck von 10 bar bei 23 °C und 6,5 bar bei 60 °C, einen schweren Einsatzbereich mit einem maximalen Betriebsdruck von 16 bar bei 23 °C und 11 bar bei 60 °C und einen schweren Einsatzbereich zur Anwendung im Bergbau mit einem maximalen Betriebsdruck von 25 bar bei 23 °C und 13 bar bei 60 °C.

Tuyaux en plastique - Types armés de textile pour applications avec de l'air comprimé - Spécifications (ISO 5774:2016)

ISO 5774:2016 spécifie les exigences relatives à quatre types de tuyaux souples en thermoplastique, armés de textile, destinés aux applications d'air comprimé dans la plage de températures de −10 °C to +60 °C.
Les quatre types sont classés comme suit: service léger pour une pression maximale de service de 7 bar à 23 °C et de 4,5 bar à 60 °C, service moyen pour une pression maximale de service de 10 bar à 23 °C et de 6,5 bar à 60 °C, service intensif pour une pression maximale de service de 16 bar à 23 °C et de 11 bar à 60 °C, et service intensif dans les mines pour une pression maximale de service de 25 bar à 23 °C et de 13 bar à 60 °C.

Polimerne cevi - S tekstilom ojačene cevi za zrak pod tlakom - Specifikacija (ISO 5774:2016)

Ta mednarodni standard določa zahteve za štiri tipe s tekstilom ojačenih cevi iz plastomerov za zrak pod tlakom v temperaturnem razponu od −10 do 60 °C. Štirje tipi so razvrščeni kot majhna obremenitev za delovni tlak 7 barov pri 23 °C in 4,5 bara pri 60 °C, srednja obremenitev za največji delovni tlak 10 barov pri 23 °C in 6,5 bara pri 60 °C, velika obremenitev za največji delovni tlak 16 barov pri 23 °C in 11 barov pri 60 °C ter velika obremenitev za uporabo v rudarstvu za največji delovni tlak 25 barov pri 23 °C in 13 barov pri 60 °C.

General Information

Status
Withdrawn
Public Enquiry End Date
09-Nov-2015
Publication Date
15-Mar-2016
Withdrawal Date
21-May-2023
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
18-May-2023
Due Date
10-Jun-2023
Completion Date
22-May-2023

Relations

Buy Standard

Standard
EN ISO 5774:2016
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
k FprEN ISO 5774:2015
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 5774:2016
01-april-2016
1DGRPHãþD
SIST EN ISO 5774:2009
3ROLPHUQHFHYL6WHNVWLORPRMDþHQHFHYL]D]UDNSRGWODNRP6SHFLILNDFLMD ,62

Plastics hoses - Textile-reinforced types for compressed-air applications - Specification
(ISO 5774:2016)
Kunststoffschläuche - Textilverstärkte Typen für Druckluftanwendungen - Anforderung
(ISO 5774:2016)
Tuyaux en plastique - Types armés de textile pour applications avec de l'air comprimé -
Spécifications (ISO 5774:2016)
Ta slovenski standard je istoveten z: EN ISO 5774:2016
ICS:
83.140.40 Gumene cevi Hoses
SIST EN ISO 5774:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 5774:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 5774:2016


EN ISO 5774
EUROPEAN STANDARD

NORME EUROPÉENNE

February 2016
EUROPÄISCHE NORM
ICS 23.040.70 Supersedes EN ISO 5774:2008
English Version

Plastics hoses - Textile-reinforced types for compressed-
air applications - Specification (ISO 5774:2016)
Tuyaux en plastique - Types armés de textile pour Kunststoffschläuche - Textilverstärkte Typen für
applications avec de l'air comprimé - Spécifications Druckluftanwendungen - Anforderung (ISO
(ISO 5774:2016) 5774:2016)
This European Standard was approved by CEN on 21 November 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5774:2016 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 5774:2016
EN ISO 5774:2016 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 5774:2016
EN ISO 5774:2016 (E)
European foreword
This document (EN ISO 5774:2016) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses
and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2016, and conflicting national standards shall
be withdrawn at the latest by August 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 5774:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 5774:2016 has been approved by CEN as EN ISO 5774:2016 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 5774:2016

---------------------- Page: 6 ----------------------

SIST EN ISO 5774:2016
INTERNATIONAL ISO
STANDARD 5774
Fourth edition
2016-01-15
Plastics hoses — Textile-reinforced
types for compressed-air applications
— Specification
Tuyaux en plastique — Types armés de textile pour applications avec
de l’air comprimé — Spécifications
Reference number
ISO 5774:2016(E)
©
ISO 2016

---------------------- Page: 7 ----------------------

SIST EN ISO 5774:2016
ISO 5774:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 5774:2016
ISO 5774:2016(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
5 Couplings and end fittings . 2
6 Materials and construction . 2
7 Dimensions and tolerances . 2
7.1 Inside diameter, tolerances and minimum wall thickness . 2
7.2 Concentricity. 3
7.3 Tolerances on length . 3
8 Physical properties . 3
8.1 Plastic compounds . 3
8.1.1 Tensile strength and elongation at break of lining and cover . 3
8.1.2 Resistance to ageing . 4
8.1.3 Loss in mass on heating . 4
8.1.4 Resistance to liquids . 4
8.1.5 Hydrolysis test . 4
8.2 Performance requirements on finished hoses . 4
8.2.1 Hydrostatic requirements . 4
8.2.2 Adhesion . 5
8.2.3 Exposure to a xenon arc lamp . 5
8.2.4 Bending test . 5
8.2.5 Low-temperature flexibility . 6
9 Frequency of testing . 6
10 Marking . 6
11 Recommendations for packaging and storage . 6
12 Test report . 7
Annex A (normative) Hydrolysis test . 8
Annex B (normative) Type and routine tests .10
Annex C (informative) Production acceptance tests .11
Annex D (informative) Couplings and end fittings .12
Bibliography .13
© ISO 2016 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 5774:2016
ISO 5774:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Rubber and plastics hoses and hose assemblies.
This fourth edition cancels and replaces the third edition (ISO 5774:2006), of which it constitutes a
minor revision.
The minor changes are as follows:
— Clause 2 has been updated: ISO 1746, ISO 4672 and ISO 11758 have been deleted and replaced by
ISO 10619-1, 10619-2 and ISO 30013.
— Pressures have been specified in MPa and bar (with the units stated) and Table 5 has been
amended accordingly. Also Clause 10 (Marking) has been slightly modified to make the
information more complete.
— The term “type approval” has been replaced by “type test”.
— The error in Annex B, where, in the column “routine testing”, the proof pressure test was marked
N.A. has been corrected. Proof pressure testing for each length of finished hose supplied has become
normative as standard for nearly all other hose product standards.
— Also Annex C (informative) has been amended (this annex is for guidance only) and the
recommendation for production acceptance testing on tensile strength/elongation at break of lining
and cover, change in length and diameter at proof pressure, adhesion, bending test has been changed
from “N.A.” to “X”, in order to monitor the quality of manufacturer’s production more efficiently.
iv © ISO 2016 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 5774:2016
ISO 5774:2016(E)

Introduction
This International Standard has been prepared to provide minimum acceptable requirements for
the satisfactory performance of flexible thermoplastics hoses, textile reinforced, for compressed-air
applications.
Maximum working pressures of each hose type are specified with two operating temperatures.
Some hose materials will require a hydrolysis test (given in Annex A).
© ISO 2016 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 5774:2016

---------------------- Page: 12 ----------------------

SIST EN ISO 5774:2016
INTERNATIONAL STANDARD ISO 5774:2016(E)
Plastics hoses — Textile-reinforced types for compressed-
air applications — Specification
1 Scope
This International Standard specifies the requirements for four types of flexible thermoplastic hose,
textile reinforced, for compressed-air applications in the temperature range from −10 °C to +60 °C.
The four types are classified as light service for a maximum working pressure of 7 bar at 23 °C and
4,5 bar at 60 °C, medium service for a maximum working pressure of 10 bar at 23 °C and 6,5 bar at
60 °C, heavy service for a maximum working pressure of 16 bar at 23 °C and 11 bar at 60 °C, and heavy
service for use in mining for a maximum working pressure of 25 bar at 23 °C and 13 bar at 60 °C.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 105-A02, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in colour
ISO 176:2005, Plastics — Determination of loss of plasticizers — Activated carbon method
ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances
on cut-to-length hoses
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1817, Rubber, vulcanized or thermoplastic — Determina
...

SLOVENSKI STANDARD
kSIST FprEN ISO 5774:2015
01-oktober-2015
3ROLPHUQHFHYL6WHNVWLORPRMDþHQHFHYL]D]UDNSRGWODNRP6SHFLILNDFLMD
,62)',6
Plastics hoses - Textile-reinforced types for compressed-air applications - Specification
(ISO/FDIS 5774:2015)
Kunststoffschläuche - Textilverstärkte Typen für Druckluftanwendungen - Anforderung
(ISO/FDIS 5774:2015)
Tuyaux en plastique - Types armés de textile pour applications avec de l'air comprimé -
Spécifications (ISO/FDIS 5774:2015)
Ta slovenski standard je istoveten z: FprEN ISO 5774
ICS:
83.140.40 Gumene cevi Hoses
kSIST FprEN ISO 5774:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

kSIST FprEN ISO 5774:2015

---------------------- Page: 2 ----------------------

kSIST FprEN ISO 5774:2015
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 5774
ISO/TC 45/SC 1
Plastics hoses — Textile-reinforced
Secretariat: DSM
types for compressed-air applications
Voting begins on:
201508­ 20­ — Specification
Voting terminates on:
Tuyaux en plastique — Types armés de textile pour applications avec
201510­ ­20
de l’air comprimé — Spécifications
Please see the administrative notes on page iii
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/FDIS 5774:2015(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN­
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2015

---------------------- Page: 3 ----------------------

kSIST FprEN ISO 5774:2015
ISO/FDIS 5774:2015(E)

ISO/CEN PARALLEL PROCESSING
This final draft has been developed within the International Organization for Standardization (ISO), and pro­
cessed under the ISO-lead mode of collaboration as defined in the Vienna Agreement. The final draft was
established on the basis of comments received during a parallel enquiry on the draft.
This final draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
two-month approval vote in ISO and formal vote in CEN.
Positive votes shall not be accompanied by comments.
Negative votes shall be accompanied by the relevant technical reasons.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------

kSIST FprEN ISO 5774:2015
ISO/FDIS 5774:2015(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
5 Couplings and end fittings . 2
6 Materials and construction . 2
7 Dimensions and tolerances . 2
7.1 Inside diameter, tolerances and minimum wall thickness . 2
7.2 Concentricity. 3
7.3 Tolerances on length . 3
8 Physical properties . 3
8.1 Plastic compounds . 3
8.1.1 Tensile strength and elongation at break of lining and cover . 3
8.1.2 Resistance to ageing . 4
8.1.3 Loss in mass on heating . 4
8.1.4 Resistance to liquids . 4
8.1.5 Hydrolysis test . 4
8.2 Performance requirements on finished hoses . 4
8.2.1 Hydrostatic requirements . 4
8.2.2 Adhesion . 5
8.2.3 Exposure to a xenon arc lamp . 5
8.2.4 Bending test . 5
8.2.5 Low-temperature flexibility . 6
9 Frequency of testing . 6
10 Marking . 6
11 Recommendations for packaging and storage . 6
12 Test report . 7
Annex A (normative) Hydrolysis test . 8
Annex B (normative) Type and routine tests .10
Annex C (informative) Production acceptance tests .11
Annex D (informative) Couplings and end fittings .12
Bibliography .13
© ISO 2015 – All rights reserved iii

---------------------- Page: 5 ----------------------

kSIST FprEN ISO 5774:2015
ISO/FDIS 5774:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Rubber and plastics hoses and hose assemblies.
This fourth edition cancels and replaces the third edition (ISO 5774:2006), of which it constitutes a
minor revision.
The minor changes are as follows:
— Clause 2 has been updated: ISO 1746, ISO 4672 and ISO 11758 have been deleted and replaced by
ISO 10619-1, 10619-2 and ISO 30013.
— Pressures have been specified in MPa and bar (with the units stated) and Table 5 has been amended
accordingly. Also Clause 10 (Marking) has been slightly modified to make the information more complete.
— The term “type approval” has been replaced by “type test”.
— The error in Annex A, where, in the column “routine testing”, the proof pressure test was marked
N.A. has been corrected. Proof pressure testing for each length of finished hose supplied has become
normative as standard for nearly all other hose product standards.
— Also Annex B (informative) has been amended (this annex is for guidance only) and the
recommendation for production acceptance testing on tensile strength/elongation at break of lining
and cover, change in length and diameter at proof pressure, adhesion, bonding test has been changed
from “N.A.” to “X”, in order to monitor the quality of manufacturer’s production more efficiently.
iv © ISO 2015 – All rights reserved

---------------------- Page: 6 ----------------------

kSIST FprEN ISO 5774:2015
ISO/FDIS 5774:2015(E)

Introduction
This International Standard has been prepared to provide minimum acceptable requirements for
the satisfactory performance of flexible thermoplastics hoses, textile reinforced, for compressed-air
applications.
Maximum working pressures of each hose type are specified with two operating temperatures.
Some hose materials will require a hydrolysis test (given in Annex A).
© ISO 2015 – All rights reserved v

---------------------- Page: 7 ----------------------

kSIST FprEN ISO 5774:2015

---------------------- Page: 8 ----------------------

kSIST FprEN ISO 5774:2015
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 5774:2015(E)
Plastics hoses — Textile-reinforced types for compressed-
air applications — Specification
1 Scope
This International Standard specifies the requirements for four types of flexible thermoplastic hose,
textile reinforced, for compressed-air applications in the temperature range from −10 °C to +60 °C.
The four types are classified as light service for a maximum working pressure of 7 bar at 23 °C and
4,5 bar at 60 °C, medium service for a maximum working pressure of 10 bar at 23 °C and 6,5 bar at 60 °C,
heavy service for a maximum working pressure of 16 bar at 23 °C and 11 bar at 60 °C, and heavy service
for use in mining for a maximum working pressure of 25 bar at 23 °C and 13 bar at 60 °C.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 105­ A02, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in colour
ISO 176:2005, Plastics — Determination of loss of plasticizers — Activated carbon method
ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances
on cut-to-length hoses
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1817, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of
hoses and the lengths of hose assemblies
ISO 8033, Rubber and plastics hoses — Determination of adhesion between components
ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary
ISO 8331, Rubber and plastics hoses and hose assemblies — Guide to selection, storage, use and maintenance
ISO 10619-1, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — Part 1:
Bending tests at ambient temperature
ISO 10619-2:2011, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness —
Part 2: Bending tests at sub-ambient temperatures
ISO 30013, Rubber and plastics hoses — Methods of exposure to laboratory light sources — Determination
of changes in colour, appearance and other physical properties
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8330 apply.
© ISO 2015 – All rights reserved 1

---------------------- Page: 9 ----------------------

kSIST FprEN ISO 5774:2015
ISO/FDIS 5774:2015(E)

4 Classification
Hoses are designated as one of the following four types depending on their pressure rating at the
specified temperature:
Type A: General industrial use — light service — for a maximum working pressure of 0,7 MPa (7
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.