SIST EN ISO 3459:2015

SLOVENSKI STANDARD
SIST EN ISO 3459:2015
01-junij-2015
1DGRPHãþD
SIST EN 911:1997
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY0HKDQVNLVSRMLPHGILWLQJLLQWODþQLPL
FHYPL0HWRGD]DSUHVNXVWHVQMHQMDVSRMHYREUHPHQMHQLKVSRGWODNRP,62

Plastic piping systems - Mechanical joints between fittings and pressure pipes - Test
method for leaktightness under negative pressure (ISO 3459:2015)
Kunststoff-Rohrleitungssysteme - Mechanische Verbindungen zwischen Fittings und
Druckrohren - Prüfung der Dichtheit bei Unterdruck (ISO 3459:2015)
Systèmes de canalisations en matières plastiques - Assemblages mécaniques entre
raccords et tubes sous pression - Méthode d'essai pour l'étanchéité sous pression
négative (ISO 3459:2015)
Ta slovenski standard je istoveten z: EN ISO 3459:2015
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
SIST EN ISO 3459:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 3459:2015

---------------------- Page: 2 ----------------------

SIST EN ISO 3459:2015

EUROPEAN STANDARD
EN ISO 3459

NORME EUROPÉENNE

EUROPÄISCHE NORM
March 2015
ICS 23.040.60 Supersedes EN 911:1995
English Version
Plastic piping systems - Mechanical joints between fittings and
pressure pipes - Test method for leaktightness under negative
pressure (ISO 3459:2015)
Systèmes de canalisations en matières plastiques - Kunststoff-Rohrleitungssysteme - Mechanische
Assemblages mécaniques entre raccords et tubes sous Verbindungen zwischen Fittings und Druckrohren - Prüfung
pression - Méthode d'essai pour l'étanchéité sous pression der Dichtheit bei Unterdruck (ISO 3459:2015)
négative (ISO 3459:2015)
This European Standard was approved by CEN on 12 December 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3459:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 3459:2015
EN ISO 3459:2015 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 3459:2015
EN ISO 3459:2015 (E)
Foreword
This document (EN ISO 3459:2015) has been prepared by Technical Committee ISO/TC 138 "Plastics pipes,
fittings and valves for the transport of fluids" in collaboration Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2015, and conflicting national standards shall be
withdrawn at the latest by September 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 911:1995.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 3459:2015 has been approved by CEN as EN ISO 3459:2015 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 3459:2015

---------------------- Page: 6 ----------------------

SIST EN ISO 3459:2015
INTERNATIONAL ISO
STANDARD 3459
Second edition
2015-03-01
Plastic piping systems — Mechanical
joints between fittings and pressure
pipes — Test method for leaktightness
under negative pressure
Systèmes de canalisations en matières plastiques — Assemblages
mécaniques entre raccords et tubes sous pression — Méthode d’essai
pour l’étanchéité sous pression négative
Reference number
ISO 3459:2015(E)
©
ISO 2015

---------------------- Page: 7 ----------------------

SIST EN ISO 3459:2015
ISO 3459:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 3459:2015
ISO 3459:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Principle . 1
3 Test parameters and requirements . 1
4 Apparatus . 1
4.1 Apparatus for procedure A . 1
4.2 Apparatus for procedure B . 2
5 Test pieces . 3
6 Procedure A: Pressure outside . 4
7 Procedure B: Vacuum inside . 4
8 Test report . 4
Annex A (normative) Test parameters . 6
© ISO 2015 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 3459:2015
ISO 3459:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO s
...