SIST EN ISO 18541-3:2021

SLOVENSKI STANDARD
SIST EN ISO 18541-3:2021
01-september-2021
Nadomešča:
SIST EN ISO 18541-3:2015
Cestna vozila - Standardiziran dostop do informacij o popravilih in vzdrževanju
avtomobilov (RMI) - 3. del: Zahteve za funkcionalni uporabniški vmesnik (ISO
18541-3:2021)
Road vehicles - Standardized access to automotive repair and maintenance information
(RMI) - Part 3: Functional user interface requirements (ISO 18541-3:2021)
Straßenfahrzeuge - Standardisierter Zugang zu Reparatur- und Wartungsinformationen
(RMI) - Teil 3: Anforderungen an die funktionale Nutzerschnittstelle (ISO 18541-3:2021)
Véhicules routiers - Normalisation de l'accès aux informations relatives à la réparation et
à la maintenance pour l'automobile (RMI) - Partie 3: Exigences fonctionnelles relatives à
l’interface utilisateur (ISO 18541-3:2021)
Ta slovenski standard je istoveten z: EN ISO 18541-3:2021
ICS:
43.040.15 Avtomobilska informatika. Car informatics. On board
Vgrajeni računalniški sistemi computer systems
43.180 Diagnostična, vdrževalna in Diagnostic, maintenance and
preskusna oprema test equipment
SIST EN ISO 18541-3:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 18541-3:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 18541-3:2021


EN ISO 18541-3
EUROPEAN STANDARD

NORME EUROPÉENNE

June 2021
EUROPÄISCHE NORM
ICS 43.180; 43.040.15 Supersedes EN ISO 18541-3:2014
English Version

Road vehicles - Standardized access to automotive repair
and maintenance information (RMI) - Part 3: Functional
user interface requirements (ISO 18541-3:2021)
Véhicules routiers - Normalisation de l'accès aux Straßenfahrzeuge - Standardisierter Zugang zu
informations relatives à la réparation et à la Reparatur- und Wartungsinformationen (RMI) - Teil 3:
maintenance pour l'automobile (RMI) - Partie 3: Anforderungen an die funktionale Nutzerschnittstelle
Exigences fonctionnelles relatives à l'interface (ISO 18541-3:2021)
utilisateur (ISO 18541-3:2021)
This European Standard was approved by CEN on 1 June 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18541-3:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 18541-3:2021
EN ISO 18541-3:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 18541-3:2021
EN ISO 18541-3:2021 (E)
European foreword
This document (EN ISO 18541-3:2021) has been prepared by Technical Committee ISO/TC 22 "Road
vehicles" in collaboration with Technical Committee CEN/TC 301 “Road vehicles” the secretariat of
which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2021, and conflicting national standards
shall be withdrawn at the latest by December 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 18541-3:2014.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 18541-3:2021 has been approved by CEN as EN ISO 18541-3:2021 without any
modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 18541-3:2021

---------------------- Page: 6 ----------------------
SIST EN ISO 18541-3:2021
INTERNATIONAL ISO
STANDARD 18541-3
Second edition
2021-06
Road vehicles — Standardized access
to automotive repair and maintenance
information (RMI) —
Part 3:
Functional user interface
requirements
Véhicules routiers — Normalisation de l'accès aux informations
relatives à la réparation et à la maintenance pour l'automobile
(RMI) —
Partie 3: Exigences fonctionnelles relatives à l’interface utilisateur
Reference number
ISO 18541-3:2021(E)
©
ISO 2021

---------------------- Page: 7 ----------------------
SIST EN ISO 18541-3:2021
ISO 18541-3:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 18541-3:2021
ISO 18541-3:2021(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviated terms . 1
5 Conventions . 2
6 Requirements overview and principles . 2
6.1 Basic principles for requirements definition . 2
6.2 Navigational pathway from standardized use cases to VM-specific navigation position . 2
6.3 VM RMI system standardized navigation . 3
6.4 Requirements clusters . 5
7 Requirements cluster 1 — Standardized access mode . 7
7.1 [FREQ-1] RMI access mode . 7
7.2 [FREQ-2] Registration and login support . 7
8 Requirements cluster 2 — Use cases map . 7
8.1 [FREQ-3] VM RMI system implemented use cases map . 7
8.2 [FREQ-4] Download area .10
9 Requirements cluster 3 — Navigational pathway .10
9.1 [FREQ-5] Navigational pathway .10
Bibliography .12
© ISO 2021 – All rights reserved iii

---------------------- Page: 9 ----------------------
SIST EN ISO 18541-3:2021
ISO 18541-3:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www. iso. org/d irectives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www. iso. org/p atents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www. iso. org/
iso/f oreword. html.
This document was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 31,
Data communication, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 301, Road vehicles, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 18541-3:2014), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— document adopted to use cases updates taken in ISO 18541-1;
— editorial corrections.
A list of all parts in the ISO 18541 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www. iso. org/m embers. html.
iv © ISO 2021 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 18541-3:2021
ISO 18541-3:2021(E)

Introduction
The ISO 18541 series includes the requirements to be fulfilled by repair and maintenance information
(RMI) systems as applied by the European Commission — Enterprise and Industry Directorate-General,
[9]
Consumer goods — Automotive industry EC mandate M/421 , dated Brussels, 21 January 2008.
This mandate relates to the EC type-approval system for vehicles falling into the scopes of Directives
[12]
70/156/EEC (replaced by 2007/46/EC ), 2002/24/EC [replaced by (EU) 168/2013] and 2003/37/
EC [replaced by (EU) 167/2013] and, in particular, to requirements for access to vehicle repair and
maintenance information by independent operators.
The purpose of the EC Mandate M/421 is to develop a standard or set of standards which specify the
requirements to provide standardized access to automotive repair and maintenance information (RMI)
for independent operators.
The ISO 18541 series only covers access to automotive repair and maintenance information for
[18] [17]
light passenger and commercial vehicles [see (EC) No 715/2007 , (EC) No 692/2008 and
[14] [16] [15]
(EU) No 566/2011 ] and heavy-duty vehicles [see (EC) No 595/2009 , (EU) No 582/2011
[13] [12]
and (EU) No 64/2012 ] based on Directive 2007/46/EC and for two-or three-wheel vehicles and
quadricycles based on regulation (EU) 168/2013.
The information included in the ISO 18541 series derives from the legislative requirements on European
level in the field of RMI and related security requirements and can be referenced by legislation in other
countries.
© ISO 2021 – All rights reserved v

---------------------- Page: 11 ----------------------
SIST EN ISO 18541-3:2021

---------------------- Page: 12 ----------------------
SIST EN ISO 18541-3:2021
INTERNATIONAL STANDARD ISO 18541-3:2021(E)
Road vehicles — Standardized access to automotive repair
and maintenance information (RMI) —
Part 3:
Functional user interface requirements
1 Scope
This document includes functional user interface requirements related to automotive repair and
maintenance information (RMI) systems in order to standardize access to RMI for independent
operators.
This document specifies all functional user interface requirements related to a vehicle manufacturer's
RMI system. These requirements will reflect the deriving needs from the use cases as specified in
ISO 18541-1.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 18541-1:2021, Road vehicles — Standardized access to automotive repair and maintenance information
(RMI) — Part 1: General information and use case definition
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 18541-1 and the following
apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
artefact
one of many kinds of tangible by-products produced during the development of software
4 Abbreviated terms
AR authorized repairer
FREQ- functional user interface requirement
IO independent operator
© ISO 2021 – All rights reserved 1

---------------------- Page: 13 ----------------------
SIST EN ISO 18541-3:2021
ISO 18541-3:2021(E)

RMI repair and maintenance information
VCI vehicle communication interface
VM vehicle manufacturer
5 Conventions
This document is based on the conventions discussed in the OSI service conventions (ISO/IEC 10731).
6 Requirements overview and principles
6.1 Basic principles for requirements definition
The basic principles have been established as a guideline to define the requirements.
— BP1: the requirements stated in this document shall not spec
...