Hot rolled spring steel flat bars - Part 2: Ribbed and grooved spring leaves - Dimensions and tolerances on shape and dimensions

This Part of this European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot rolled spring steel flat bars for ribbed and grooved spring leaves.
This standard is applicable only to steel flats produced from steel grades specified in EN 10089.

Warmgewalzte Flachstäbe aus Federstahl - Teil 2: Gerippter Federstahl - Maße, Formtoleranzen und Grenzabmaße

Dieser Teil dieser Europäischen Norm legt die Nennmaße, Grenzabmaße und Formtoleranzen warmgewalzter Flachstäbe aus Federstahl für gerippte Blattfedern fest.
Diese Norm gilt nur für Flachstäbe aus Federstahl, die aus den in EN 10089 festgelegten Stahlsorten hergestellt wurden.

Plats laminés a chaud en aciers a ressort - Partie 2: Plats pour lames de ressorts rainées et nervurées - Dimensions et tolérances sur la forme et les dimensions

La présente partie de la présente norme européenne spécifie les dimensions nominales ainsi que les tolérances sur les dimensions et la forme des plats en acier laminés a chaud pour lames de ressorts rainées et nervurées.
La présente norme s'applique uniquement aux plats en acier produits pour les nuances d'acier spécifiées dans l'EN 10089.

Hot rolled spring steel flat bars - Part 2: Ribbed and grooved spring leaves - Dimensions and tolerances on shape and dimensions

General Information

Status
Published
Publication Date
31-May-2004
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jun-2004
Due Date
01-Jun-2004
Completion Date
01-Jun-2004

Buy Standard

Standard
EN 10092-2:2004
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Hot rolled spring steel flat bars - Part 2: Ribbed and grooved spring leaves - Dimensions and tolerances on shape and dimensionsWarmgewalzte Flachstäbe aus Federstahl - Teil 2: Gerippter Federstahl - Maße, Formtoleranzen und GrenzabmaßePlats laminés a chaud en aciers a ressort - Partie 2: Plats pour lames de ressorts rainées et nervurées - Dimensions et tolérances sur la forme et les dimensionsHot rolled spring steel flat bars - Part 2: Ribbed and grooved spring leaves - Dimensions and tolerances on shape and dimensions77.140.60Jeklene palice in drogoviSteel bars and rods77.140.25Vzmetna jeklaSpring steelsICS:Ta slovenski standard je istoveten z:EN 10092-2:2003SIST EN 10092-2:2004en01-junij-2004SIST EN 10092-2:2004SLOVENSKI
STANDARD



SIST EN 10092-2:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10092-2October 2003ICS 77.140.25; 77.140.60English versionHot rolled spring steel flat bars - Part 2: Ribbed and groovedspring leaves - Dimensions and tolerances on shape anddimensionsPlats laminés à chaud en aciers à ressort - Partie 2: Platspour lames de ressorts rainées et nervurées - Dimensionset tolérances sur la forme et les dimensionsWarmgewalzte Flachstäbe aus Federstahl - Teil 2:Gerippter Federstahl - Maße, Formtoleranzen undGrenzabmaßeThis European Standard was approved by CEN on 4 September 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10092-2:2003 ESIST EN 10092-2:2004



EN 10092-2:2003 (E)2ContentspageForeword.31Scope.42Normative references.43Terms and definitions.44Designation.45Dimensions.46Tolerances on dimensions and shape.66.1Thickness (t).66.2Width (b).66.3Length (L).66.4Straightness (q).66.5Convexity and Concavity.66.6Lateral offset of the groove and the rib.67Measurements.87.1Thickness and width.87.2Length.87.3Straightness.87.4Convexity and Concavity.97.5Lateral offset of the groove and the rib.9SIST EN 10092-2:2004



EN 10092-2:2003 (E)3ForewordThis document (EN 10092-2:2003) has been prepared by Technical Committee ECISS/TC 11"Structural steel sections and hot rolled steel bars for engineering use — Dimensions and tolerances",the secretariat of which is held by BSI.This European Standard shall be given the status of a national standard, either by publicat
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.