Geotextiles and geotextile-related products - Characteristics required for use in erosion control works (coastal protection, bank revetments)

This European Standard specifies the relevant characteristics of geotextiles and geotextile-related products used in erosion control works for preventing the migration of fine-graded material into layers of coarser material due to alternating hydraulic gradients, and the appropriate test methods to determine these characteristics.
This European Standard covers applications in coastal protection and bank revetment. This European Standard does not cover surface erosion, where the geotextile or geotextile-related product is located at the surface.
The intended use of these geotextiles or geotextile-related products is to fulfil one or more of the following functions: filtration, separation, and reinforcement. The separation function will always occur in conjunction with filtration or reinforcement, and hence will not be specified alone.
This European Standard is not applicable to geosynthetic barriers, as defined in EN ISO 10318.
This European Standard provides for the assessment and verification of constancy of performance of the product to this European Standard and for factory production control procedures.
NOTE   Particular application cases may contain requirements regarding additional properties and – preferably standardised – test methods, if they are technically relevant.
This European Standard may be used to derive design values by taking into account factors within the context of the definitions given in EN 1997 1 (Eurocode 7), e.g. factors of safety. The design life of the product should be determined, since its function may be temporary, as a construction expediency, or permanent, for the lifetime of the structure.

Geotextilien und geotextilverwandte Produkte - Geforderte Eigenschaften für die Anwendung in Erosionsschutzanlagen (Küstenschutz, Deckwerksbau)

Diese Europäische Norm legt die wichtigsten Eigenschaften von Geotextilien und geotextilverwandten Produkten, die in Erosionsschutzanlagen verwendet werden, fest, um das Abwandern von feinkörnigen Materialien in Schichten von gröberen Materialien infolge von wechselnden hydraulischen Gefällen zu verhindern, sowie die geeigneten Prüfverfahren zur Bestimmung dieser Eigenschaften fest.
Diese Europäische Norm behandelt Anwendungen in Küstenschutz und Deckwerksbau. Diese Europäische Norm behandelt jedoch nicht Oberflächenerosionsschutz, wobei das Geotextil oder geotextilverwandte Produkt sich an der Oberfläche befindet.
Bei ihrer vorgesehenen Anwendung werden diese Geotextilien und geotextilverwandten Produkte eine oder mehrere der folgenden Funktionen erfüllen: Filtern, Trennen und Bewehren. Die Trennfunktion wird immer in Verbindung mit Filtern oder Bewehren genutzt, folglich ist Trennen nie allein vorgegeben.
Diese Europäische Norm ist nicht auf geosynthetische Dichtungsbahnen anwendbar, wie in EN ISO 10318-1 festgelegt.
Diese Europäische Norm behandelt die Bewertung und Überprüfung der Leistungsbeständigkeit des Produkts nach dieser Europäischen Norm und die Verfahren für die werkseigene Produktionskontrolle.
Besondere Anwendungen können Anforderungen hinsichtlich zusätzlicher Eigenschaften und - vorzugsweise genormte - Prüfverfahren enthalten, wenn diese technisch relevant sind.
Diese Europäische Norm darf zur Festlegung von Bemessungswerten herangezogen werden, in dem die im Zusammenhang mit den in EN 1997-1 (Eurocode 7) angegebenen Definitionen berücksichtigt werden , z. B. Sicherheitsbeiwerte. Für das Produkt sollte die Bemessungsdauer festgelegt werden, weil seine Funktion zeitlich befristet sein darf, als Einbauhilfe, oder dauerhaft, der Lebensdauer des Bauwerks entsprechend.

Géotextiles et produits apparentés - Caractéristiques requises pour l’utilisation dans les ouvrages de lutte contre l’érosion (protection côtière et revêtement de berge)

La présente Norme européenne spécifie les caractéristiques pertinentes des géotextiles et produits apparentés utilisés dans les ouvrages de lutte contre l'érosion dans le but de prévenir la migration de matière à granulométrie fine dans des couches de matériau plus grossier sous l'influence de gradients hydrauliques alternants. Cette norme spécifie également les méthodes d'essai appropriées pour déterminer ces caractéristiques.
La présente Norme européenne couvre les applications en protection côtière et revêtement de berge. La présente Norme européenne ne couvre pas l'érosion de surface, où le géotextile ou produit apparenté est situé en surface.
L'utilisation prévue de ces géotextiles ou produits apparentés est de remplir au moins l'une des fonctions suivantes : filtration, séparation et renforcement. La fonction séparation étant toujours utilisée conjointement avec une filtration ou un renforcement, celle-ci n'est pas spécifiée seule.
La présente Norme européenne ne s'applique pas aux géomembranes et géosynthétiques bentonitiques tels que définis dans l'EN ISO 10318 1.
La présente Norme européenne permet d'évaluer et de vérifier la constance des performances du produit à la présente Norme européenne et les procédures de contrôle de la production en usine.
Des cas d'application particuliers peuvent contenir des exigences sur des propriétés supplémentaires et méthodes d'essai – si possible normalisées – si elles sont techniquement pertinentes.
La présente Norme européenne peut être utilisée pour déduire les valeurs de calcul en prenant en compte les facteurs définis dans l'EN 1997 1 (Eurocode 7), par exemple les facteurs de sécurité. Il convient de déterminer la durée de vie prévue du produit, puisque sa fonction peut être provisoire, pour des besoins de construction, ou permanente, pour la durée de vie de la structure.

Geotekstilije in geotekstilijam sorodni izdelki - Značilnosti, ki se zahtevajo pri nadzoru erozije (zaščita obale, zaščita z nasipom)

Ta evropski standard določa pomembne značilnosti geotekstilij in geotekstilijam sorodnih izdelkov, ki se uporabljajo pri nadzoru erozije za preprečevanje prodiranja materiala fino stopnjevane zrnavosti v plasti bolj grobega materiala zaradi izmeničnih hidravličnih gradientov, ter ustrezne preskusne metode za določitev teh značilnosti.
Ta evropski standard zajema načine uporabe pri zaščiti obale in zaščiti z nasipom. Ta evropski standard ne zajema površinske erozije, ko je geotekstilija in geotekstiliji sorodni izdelek na površini.
Te geotekstilije in geotekstilijam sorodni izdelki naj bi imeli eno ali več naslednjih funkcij: filtriranje, ločevanje in ojačitev. Funkcija ločevanja se bo vedno pojavljala skupaj s filtriranjem ali ojačitvijo, zato ne bo ločeno opredeljena.
Ta evropski standard se ne uporablja za geosintetične zapore, kakor so opredeljene v standardu EN ISO 10318.
Ta evropski standard omogoča ocenjevanje in preverjanje stalnosti funkcionalnosti izdelka v skladu s tem evropskim standardom ter postopke kontrole proizvodnje v obratu.
OPOMBA: Posamezni primeri uporabe lahko vključujejo zahteve glede dodatnih lastnosti in – po možnosti standardiziranih – preskusnih metod, če so tehnično pomembni.
Ta evropski standard se lahko uporablja za izpeljavo projektnih vrednosti ob upoštevanju dejavnikov v okviru definicij iz standarda EN 1997 1 (Evrokod 7), npr. dejavnikov varnosti. Določila naj bi se projektna življenjska doba izdelka, saj je njegova funkcija začasna, kot zagotavljanje primernosti za gradnjo, ali stalna, tj. za življenjsko dobo konstrukcije.

General Information

Status
Published
Public Enquiry End Date
02-Mar-2016
Publication Date
09-Nov-2016
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
21-Oct-2016
Due Date
26-Dec-2016
Completion Date
10-Nov-2016

Relations

Buy Standard

Standard
EN 13253:2016
English language
44 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Geotextilien und geotextilverwandte Produkte - Geforderte Eigenschaften für die Anwendung in Erosionsschutzanlagen (Küstenschutz, Deckwerksbau)Géotextiles et produits apparentés - Caractéristiques requises pour l’utilisation dans les ouvrages de lutte contre l’érosion (protection côtière et revêtement de berge)Geotextiles and geotextile-related products - Characteristics required for use in erosion control works (coastal protection, bank revetments)93.020Zemeljska dela. Izkopavanja. Gradnja temeljev. Dela pod zemljoEarthworks. Excavations. Foundation construction. Underground works59.080.70GeotekstilijeGeotextilesICS:Ta slovenski standard je istoveten z:EN 13253:2016SIST EN 13253:2016en,fr,de01-december-2016SIST EN 13253:2016SLOVENSKI
STANDARDSIST EN 13253:2014+A1:20151DGRPHãþD



SIST EN 13253:2016



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13253
October
t r s x ICS
w {ä r z rä y r Supersedes EN
s u t w uã t r s v ªA sã t r s wEnglish Version
Geotextiles and geotextileærelated products æ Characteristics required for use in erosion control works Géotextiles et produits apparentés æ Caractéristiques requises pour l 5utilisation dans les ouvrages de lutte
Geotextilien und geotextilverwandte Produkte æ Geforderte Eigenschaften für die Anwendung in This European Standard was approved by CEN on
v June
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u t w uã t r s x ESIST EN 13253:2016



EN 13253:2016 (E) 2 Contents Page European foreword . 4 Introduction . 5 1 Scope . 6 2 Normative references . 6 3 Terms, definitions and abbreviations . 7 3.1 Terms and definitions . 7 3.2 Abbreviations . 8 4 Required characteristics and corresponding methods of test. 8 4.1 General . 8 4.2 Selection of the appropriate standard in a specific application . 8 4.3 Characteristics relevant to specific conditions of use . 11 4.3.1 Stiffness at 2 %, 5 % and 10 % . 11 4.3.2 Tensile strength of seams and joints . 11 4.3.3 Static puncture . 11 4.3.4 Friction characteristics . 11 4.3.5 Tensile creep . 11 4.3.6 Resistance to damage during installation . 11 4.3.7 Water permeability normal to the plane . 11 4.4 Release of dangerous substances . 11 5 Assessment and verification of constancy of performance (AVCP) . 12 5.1 General . 12 5.2 Presentation of characteristics . 12 5.3 Product type determination (PTD) . 12 5.4 Factory production control (FPC) . 13 5.5 Verification of values . 13 5.6 Initial inspection of factory and of FPC . 14 5.7 Continuous surveillance of FPC . 14 6 Marking . 14 Annex A (normative)
Factory production control . 15 A.1 Factory production control scheme . 15 A.1.1 General . 15 A.1.2 Product design . 15 A.1.3 Production . 15 A.1.4 Finished products . 15 A.1.5 Provisions applicable to A.1.2, A.1.3 and A.1.4 (to be used where appropriate) . 16 A.2 Assessment of a factory production control (FPC) system. 17 A.2.1 General . 17 A.2.2 Checklist . 17 A.2.3 Test frequency . 21 Annex B (normative)
Durability aspects . 22 B.1 General . 22 B.1.1 Service life . 22 SIST EN 13253:2016



EN 13253:2016 (E) 3 B.1.2 Initial and repeat testing of durability. 22 B.1.3 Use of rework material . 23 B.2 Weathering (all products) . 23 B.3 Products used in non-reinforcing applications and with service lives up to 5 years . 23 B.4 Other applications and service lives up to 25 years, 50 years and 100 years . 24 B.4.1 General . 24 B.4.2 Tests for specific materials . 24 Annex C (informative)
Guidelines for the selection of the appropriate standard in a specific application . 28 Annex D (informative)
Significant technical changes to the superseded standard . 30 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation . 31 Bibliography . 44
SIST EN 13253:2016



EN 13253:2016 (E) 4 European foreword This document (EN 13253:2016) has been prepared by Technical Committee CEN/TC 189 “Geosynthetics”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2017, and conflicting national standards shall be withdrawn at the latest by July 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13253:2014+A1:2015. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Regulation No 305/2011. For relationship with Regulation (EU) Nr. 305/2011, see informative Annex ZA, which is an integral part of this document. Annex D provides details of significant technical changes between this European Standard and the previous edition. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 13253:2016



EN 13253:2016 (E) 5 Introduction This European Standard allows manufacturers to describe geotextiles and geotextile-related products on the basis of declared values for characteristics relevant to the intended use and if tested to the specified method. It also includes procedures for the assessment and verification of constancy of performance and factory production control. This European Standard may also be used by designers, end-users and other interested parties to define which functions and conditions of use are relevant. The term “product” used in this European Standard refers to a geotextile or geotextile-related product. This European Standard is part of a series of standards, addressing the requirements for geotextiles and geotextile-related products when used in a specific application. Annex C provides guidance on how to select the appropriate standard. SIST EN 13253:2016



EN 13253:2016 (E) 6 1 Scope This European Standard specifies the relevant characteristics of geotextiles and geotextile-related products used in erosion control works for preventing the migration of fine-graded material into layers of coarser material due to alternating hydraulic gradients, and the appropriate test methods to determine these characteristics. This European Standard covers applications in coastal protection and bank revetment. This European Standard does not cover surface erosion, where the geotextile or geotextile-related product is located at the surface. The intended use of these geotextiles or geotextile-related products is to fulfil one or more of the following functions: filtration, separation and reinforcement. The separation function will always occur in conjunction with filtration or reinforcement, and hence will not be specified alone. This European Standard is not applicable to geosynthetic barriers, as defined in EN ISO 10318-1. This European Standard provides for the assessment and verification of constancy of performance of the product to this European Standard and for factory production control procedures. Particular application cases may contain requirements regarding additional properties and – preferably standardized – test methods, if they are technically relevant. This European Standard may be used to derive design values by taking into account factors within the context of the definitions given in EN 1997-1 (Eurocode 7), e.g. factors of safety. The design life of the product should be determined, since its function may be temporary, as a construction expediency, or permanent, for the lifetime of the structure. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12224, Geotextiles and geotextile-related products - Determination of the resistance to weathering EN 12226, Geosynthetics - General tests for evaluation following durability testing EN 12447, Geotextiles and geotextile-related products - Screening test method for determining the resistance to hydrolysis in water EN ISO 1043-1, Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics (ISO 1043-1) EN ISO 3696, Water for analytical laboratory use - Specification and test methods (ISO 3696) EN ISO 9862, Geosynthetics - Sampling and preparation of test specimens (ISO 9862) EN ISO 10318-1, Geosynthetics - Part 1: Terms and definitions (ISO 10318-1) EN ISO 10319, Geosynthetics - Wide-width tensile test (ISO 10319) EN ISO 10320, Geotextiles and geotextile-related products - Identification on site (ISO 10320) EN ISO 10321, Geosynthetics - Tensile test for joints/seams by wide-width strip method (ISO 10321) SIST EN 13253:2016



EN 13253:2016 (E) 7 EN ISO 10722, Geosynthetics - Index test procedure for the evaluation of mechanical damage under repeated loading - Damage caused by granular material (ISO 10722) EN ISO 11058, Geotextiles and geotextile-related products - Determination of water permeability characteristics normal to the plane, without load (ISO 11058) EN ISO 12236, Geosynthetics - Static puncture test (CBR test) (ISO 12236) EN ISO 12956, Geotextiles and geotextile-related products - Determination of the characteristic opening size (ISO 12956) EN ISO 12957-1, Geosynthetics - Determination of friction characteristics - Part 1: Direct shear test (ISO 12957-1) EN ISO 12957-2, Geosynthetics - Determination of friction characteristics - Part 2: Inclined plane test (ISO 12957-2) EN ISO 13426-1, Geotextiles and geotextile-related products - Strength of internal structural junctions - Part 1: Geocells (ISO 13426-1) EN ISO 13426-2, Geotextiles and geotextile-related products - Strength of internal structural junctions - Part 2: Geocomposites (ISO 13426-2) EN ISO 13431, Geotextiles and geotextile-related products - Determination of tensile creep and creep rupture behaviour (ISO 13431) EN ISO 13433, Geosynthetics - Dynamic perforation test (cone drop test) (ISO 13433) EN ISO 13438, Geotextiles and geotextile-related products - Screening test method for determining the resistance to oxidation (ISO 13438) ISO 10390, Soil quality — Determination of pH ASTM D4603 — 03(2011)e1, Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer ASTM D7409 — 15, Standard Test Method for Carboxyl End Group Content of Polyethylene Terephthalate (PET) Yarns 3 Terms, definitions and abbreviations 3.1 Terms and definitions For the purposes of this document, the terms and definitions given EN ISO 10318-1 and the following apply. 3.1.1 product geotextile or geotextile-related product 3.1.2 specification document in which the work, functions and specific conditions of use of the product are described SIST EN 13253:2016



EN 13253:2016 (E) 8 3.1.3 rework material RWM material that is generated in a process and capable of being reclaimed within the same process that generated it 3.1.4 post-consumer material PCM material generated by households or by commercial, industrial and institutional facilities in their role as end-users of the product which can no longer be used for its intended purpose Note 1 to entry: This includes returns of material from the distribution chain. 3.1.5 post-industrial material PIM material diverted from the waste stream during a manufacturing process 3.2 Abbreviations For the purposes of this document, the abbreviations given in EN ISO 1043-1 and EN ISO 10318-1 and the following apply. — AR: aramid — GCO-R: geocomposite reinforcement 4 Required characteristics and corresponding methods of test 4.1 General The main functions of geotextiles and geotextile-related products used in erosion control works are filtration, separation and reinforcement. If a drainage or erosion control system is integrated in the construction, the requirements of the appropriate standards shall also be fulfilled. As the separation function is always used in conjunction with another function, the separation function shall never be specified alone. The specification shall define which functions and conditions of use are relevant (see Table 1). The producer shall provide the necessary data based on the requirements and test methods specified in this European Standard, as described in 5.1. The characteristics, their relevance to the conditions of use, and the test methods to be used, are specified in Table 1. The list of characteristics in Table 1 includes those relevant to all conditions of use (A), and those relevant to specific conditions of use (S). The indication “–” means that the characteristic is not relevant for that function. Where, for the same property, data for more than one function shall be provided, the following ranking order shall be observed: A overrules S, and S overrules “–”. The functions and conditions of use, corresponding with the S-coded characteristics in Table 1, are specified in 4.3. Durability shall be assessed in accordance with the requirements of Annex B. 4.2 Selection of the appropriate standard in a specific application Guidelines for the selection of the appropriate standard in a specific application are given in Annex C. SIST EN 13253:2016



EN 13253:2016 (E) 9 Table 1 — Geotextiles and geotextile-related products used in the construction of erosion control works – Functions, function-related characteristics and test methods to be used Characteristic Test method Functions Filtration Separation Reinforcement (1) Tensile strength b EN ISO 10319 A A A (2) Elongation at maximum load EN ISO 10319 A A A (3) Stiffness at 2 %, 5 % and 10 % EN ISO 10319 – – S (4) Tensile strength of seams and joints c d EN ISO 10321 S S S (5) Static puncture resistance (CBR test) a b EN ISO 12236 S A A (6) Dynamic perforation resistance (cone drop test) a EN ISO 13433 A A A (7) Friction EN ISO 12957-1; EN ISO 12957-2 S S S (8) Tensile creep EN ISO 13431 – – S (9) Resistance to damage during installation under repeated loading EN ISO 10722 S S S (10) Characteristic opening size EN ISO 12956 A A – (11) Water permeability normal to the plane (velocity index) EN ISO 11058 A A S (12) Durability According to Annex B A A A Relevance of codes:
A: relevant to all conditions of use
S: relevant to specific conditions of use
“–”: indicates that the characteristic is not relevant for that function. SIST EN 13253:2016



EN 13253:2016 (E) 10 Characteristic Test method Functions Filtration Separation Reinforcement a
Static puncture resistance may not be relevant for some types of products, e.g. GGR, GCO-R or GST. b
If the mechanical properties (tensile strength and static puncture) are coded “A” in this Table, the use of only one, either tensile strength or static puncture, is usually sufficient in a project specification. c
The strength of internal structural junctions of geocells shall be tested in accordance with EN ISO 13426-1. d
The strength of internal structural junctions of geocomposites shall be tested in accordance with EN ISO 13426-2. SIST EN 13253:2016



EN 13253:2016 (E) 11 4.3 Characteristics relevant to specific conditions of use 4.3.1 Stiffness at 2 %, 5 % and 10 % Data on stiffness are necessary for the reinforcement function if the deformation of the structure needs to be evaluated. 4.3.2 Tensile strength of seams and joints Data on tensile strength of seams and joints are necessary for all functions if the product is to be mechanically jointed and if load is transferred across the seams and joints. 4.3.3 Static puncture Data on static puncture or - as an alternative - on tensile strength, are necessary for the filtration function if required by the specification, i.e. when the site loading conditions are such that there is a potential risk of static puncture of the filter layer. 4.3.4 Friction characteristics Data on friction characteristics are necessary for the functions separation and filtration when the product is used in a situation where a differential movement can take place between the product and adjacent material that may endanger the stability of the works. The friction characteristics can be measured, using site specific materials, by a direct shear test according to EN ISO 12957-1 or, in the case of loads up to 5 kPa, by an inclined plane test according to EN ISO 12957-2. Friction behaviour with the adjacent construction materials, e.g. the soil or the geosynthetic barrier, should also be considered. 4.3.5 Tensile creep Data on tensile creep can be used to give an indication of the resistance to sustained loading, when the product fulfils a reinforcement function. 4.3.6 Resistance to damage during installation EN ISO 10722 can be used as an index test giving the relative performance of the product. Testing with site specific soil and conditions may give more relevant results for specific design. 4.3.7 Water permeability normal to the plane Data on water permeability are necessary when the reinforced structure is subject to water flow. 4.4 Release of dangerous substances National regulations on dangerous substances may require verification and declaration on release, and sometimes content, when construction products covered by this European Standard are placed on those markets. In the absence of European harmonized test methods, verification and declaration on release/content should be done taking into account national provisions in the place of use. NOTE An informative database covering European and national provisions on dangerous substances is available at http://ec.europa.eu/growth/tools-databases/cp-ds/index_en.htm. SIST EN 13253:2016



EN 13253:2016 (E) 12 5 Assessment and verification of constancy of performance (AVCP) 5.1 General The compliance of geotextiles and geotextile-related products with the requirements of this European Standard and with the declared values shall be demonstrated by: — Product type determination (PTD); — Factory production control (FPC) by the manufacturer, including product assessment. The manufacturer shall always retain the overall control and shall have the necessary means to take responsibility for the product. 5.2 Presentation of characteristics The characteristics specified in Table 2, except for durability, shall be expressed as mean values and tolerance value(s) corresponding to the 95 % confidence level. The values expressed may be verified using the procedure referred to in 5.5. NOTE The 95 % confidence level corresponds to the mean value minus (and/or plus) a tolerance value (see Annex ZA, table ZA1.X column Notes). Both the mean value and the tolerance value are defined by the manufacturer to be representative of the performance of the product for the corresponding characteristic (these two values are not necessarily based on a statistical calculation). Information on durability shall be expressed in accordance with Annex B. 5.3 Product type determination (PTD) PTD tests shall be carried out by the manufacturer to define the values of the properties to be declared for the product to satisfy the requirements of this European Standard. PTD tests shall also be carried out on existing products when a change in the basic materials or manufacturing procedures affects the declared properties or the use of a product. In these cases the PTD tests are those for the properties which are affected or shall be confirmed and new properties introduced by a change of use. The tests to be conducted shall be reference tests as specified in this standard and shall be selected from the characteristics specified in Table 2, consistent with the product’s intended use: Table 2 — Characteristics required for PTD and AVCP Characteristic Functions Tensile strength Filtration, separation, reinforcement Elongation at maximum load Filtration, separation, reinforcement Static puncture resistance (CBR test) Separation, reinforcement Dynamic perforation resistance (cone drop test) Separation, filtration, reinforcement Characteristic opening size Filtration, separation Water permeability normal to the plane Filtration, separation Durability a Filtration, separation, reinforcement SIST EN 13253:2016



EN 13253:2016 (E) 13 a
For the durability aspects, see Table 1 and Annex B. The results of PTD tests shall be recorded and be available for inspection. The sample for the PTD tests shall be drawn according to EN ISO 9862 from a normal production run using the same materials and forming processes as used for the full production process. The size of the sample shall be big enough to allow the determination of the characteristics specified in Table 2. Handmade samples, short trial batches and other development prototypes may be tested by the same methods, but shall not be used for establishing characteristic values in PTD tests. 5.4 Factory production control (FPC) A FPC scheme shall be established and documented in a manual prior to a product type being placed on the market. Subsequently, any fundamental changes in raw materials and additives, manufacturing procedures or the control scheme that affect the properties or use of a product shall be recorded in the manual. The manual shall include the FPC procedures relevant to the declared properties, as confirmed by the product type determination. The FPC procedures shall consist of a permanent internal production control system to ensure that such products comply with this European Standard and that the measured values conform to the declared values. Annex A (normative) lists all the items that shall be considered to determine the appropriate control measures for a product. The manufacturer shall establish control measures for the relevant items and record them in his FPC manual. These measures shall be described in detail, including the type of tests to be performed and the frequency of these tests (see also A.2). When relevant, the procedure given in A.2.3 shall be used to check the conformity of the product for one or more characteristics. 5.5 Verification of values If verification of values is required, the compliance of characteristics with the values defined in 5.2 shall be based on measurements made on two representative samples (A and B), taken from two different rolls. Sampling shall be made
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.