SIST EN 60294:2013

SLOVENSKI STANDARD
SIST EN 60294:2013
01-januar-2013
0HULWHYGLPHQ]LMFLOLQGULþQHNRPSRQHQWH]RVQLPLSULNOMXþNL
Measurement of the dimensions of a cylindrical component with axial terminations
Bestimmung der Maße eines zylindrischen Bauelementes mit zwei axialen Anschlüssen
Mesure des dimensions d'un composant cylindrique à sorties axiales
Ta slovenski standard je istoveten z: EN 60294:2012
ICS:
31.020 Elektronske komponente na Electronic components in
splošno general
SIST EN 60294:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60294:2013

---------------------- Page: 2 ----------------------

SIST EN 60294:2013

EUROPEAN STANDARD
EN 60294

NORME EUROPÉENNE
October 2012
EUROPÄISCHE NORM

ICS 31.020


English version


Measurement of the dimensions of a cylindrical component
with axial terminations
(IEC 60294:2012)


Mesure des dimensions d'un composant Bestimmung der Maße eines zylindrischen
cylindrique à sorties axiales Bauelementes mit axialen Anschlüssen
(CEI 60294:2012) (IEC 60294:2012)





This European Standard was approved by CENELEC on 2012-08-17. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60294:2012 E

---------------------- Page: 3 ----------------------

SIST EN 60294:2013
EN 60294:2012 - 2 -
Foreword
The text of document 40/2154/FDIS, future edition 2 of IEC 60294, prepared by IEC/TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 60294:2012.
The following dates are fixed:
(dop) 2013-05-17
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-08-17
• latest date by which the national
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice
The text of the International Standard IEC 60294:2012 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60717 NOTE Harmonised as EN 60717.
IEC 61192-3 NOTE Harmonised as EN 61192-3.

---------------------- Page: 4 ----------------------

SIST EN 60294:2013
- 3 - EN 60294:2012
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60301 - Preferred diameters of wire terminations EN 60301 -
of capacitors and resistors

---------------------- Page: 5 ----------------------

SIST EN 60294:2013

---------------------- Page: 6 ----------------------

SIST EN 60294:2013



IEC 60294

®


Edition 2.0 2012-07




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Measurement of the dimensions of a cylindrical component with axial

terminations




Mesure des dimensions d'un composant cylindrique à sorties axiales

















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX M


ICS 31.020 ISBN 978-2-83220-229-6



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60294:2013
– 2 – 60294 © IEC:2012
CONTENTS

FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Body length . 5
3.1 General . 5
3.2 Standard gauge plates for components with axial wire terminations . 5
3.3 Special gauge plates for components with glass-metal seals or other
discontinuities in their axial wire terminations . 7
4 Coating material extending onto wire terminations . 8
5 Overall body diameter . 9
6 Information to be given in the relevant specification. 10
Annex A (informative) Cross-reference . 11
Bibliography . 12

Figure 1 – Standard gauge plates . 6
Figure 2 – Special gauge plates . 7
Figure 3 – Gauge plate for checking coating material extended onto a wire termination . 8
Figure 4 – Straight tube diameter gauge . 9


Table 1 – Slot width or hole diameter for standard gauge plates . 6
Table A.1 – Cross reference . 11

---------------------- Page: 8 ----------------------

SIST EN 60294:2013
60294 © IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

MEASUREMENT OF THE DIMENSIONS
OF A CYLINDRICAL COMPONENT WITH AXIAL TERMINATIONS

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60294 has been prepared by IE
...