SIST EN ISO 8741:2001
(Main)Grooved pins - Half-length reverse taper grooved (ISO 8741:1997)
Grooved pins - Half-length reverse taper grooved (ISO 8741:1997)
Steckkerbstifte (ISO 8741:1997)
Diese Internationale Norm beschreibt die Eigenschaften von Steckkerbstiften aus Stahl oder aus astenitischem nichtrostendem Stahl, mit drei gleichmäßig verteilten Längskerben auf der Außenfläche. Die Kerbstifte haben einen Nenndurchmesser d1 von 1,5 bis einschließlich 25 mm. Der zu jeder Seite der Kerbe verdrängte Werkstoff, der den aufgeweiterten Durchmesser d2 bildet, welcher größer als der Nenndurchmesser d1 ist, führt zu einer kraftschlüssigen Verbindung, wenn diese Kerbstifte in eine Bohrung mit einem Durchmesser gleich dem Nenndurchmesser d1 gepreßt werden.
Goupilles cannelées a cannelures progressives renversées sur la moitié de la longueur non débouchantes (ISO 8741:1997)
La présente Norme internationale prescrit les caractéristiques des goupilles cannelées en acier ou en acier inoxydable austénitique, à trois cannelures progressives renversées sur la moitié de leur longueur, non débouchantes et régulièrement espacées, de diamètre nominal, d1, de 1,5 mm à 25 mm inclus. Le matériau refoulé de chaque côté des cannelures forme un renflement dont le diamètre d2, supérieur au diamètre nominal d1, permet un ajustement serré de ces goupilles cannelées lorsqu'elles sont emmanchées en force dans un trou de diamètre de perçage égal au diamètre nominal de la goupille d1 (voir article 4).
Zasekani zatiči z upadajočo globino brazd na pol dolžine (ISO 8741: 1997)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8741:2001
01-julij-2001
1DGRPHãþD
SIST EN 28741:1996
=DVHNDQL]DWLþL]XSDGDMRþRJORELQREUD]GQDSROGROåLQH ,62
Grooved pins - Half-length reverse taper grooved (ISO 8741:1997)
Steckkerbstifte (ISO 8741:1997)
Goupilles cannelées a cannelures progressives renversées sur la moitié de la longueur
non débouchantes (ISO 8741:1997)
Ta slovenski standard je istoveten z: EN ISO 8741:1997
ICS:
21.060.50 =DWLþLåHEOML Pins, nails
SIST EN ISO 8741:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8741:2001
---------------------- Page: 2 ----------------------
SIST EN ISO 8741:2001
---------------------- Page: 3 ----------------------
SIST EN ISO 8741:2001
---------------------- Page: 4 ----------------------
SIST EN ISO 8741:2001
---------------------- Page: 5 ----------------------
SIST EN ISO 8741:2001
---------------------- Page: 6 ----------------------
SIST EN ISO 8741:2001
INTERNATIONAL ISO
STANDARD 8741
Second edition
1997-11-01
Grooved pins — Half-length reverse-taper
grooved
Goupilles cannelées à cannelures progressives renversées sur la moitié
de la longueur non débouchantes
A
Reference number
ISO 8741:1997(E)
---------------------- Page: 7 ----------------------
SIST EN ISO 8741:2001
ISO 8741:1997(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 8741 was prepared by Technical Committee
ISO/TC 2, Fasteners.
This second edition cancels and replaces the first edition (ISO 8741:1986),
which has been technically revised.
© ISO 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet central@iso.ch
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii
---------------------- Page: 8 ----------------------
SIST EN ISO 8741:2001
©
INTERNATIONAL STANDARD ISO ISO 8741:1997(E)
Grooved pins — Half-length reverse taper grooved
1 Scope
This International Standard specifies the characteristics of half-length reverse taper grooved pins made of
steel or austenitic stainless steel which have three equally spaced grooves impressed longitudinally on their
exterior surface, with nominal diameter, d , from 1,5 mm to 25 mm inclusive.
1
The displaced material to each side of the grooves forming an expanded diameter d which is larger than the
2
nominal diameter d will cause a non-positive locking fit when these grooved pins are forced into a drilled hole
1
equal to the nominal diameter d (see clause 4).
1
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject
to revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO
maintain registers of currently
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.