SIST EN 15057:2006

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.PHWRGDFaserzement-Wellplatten - SchlagfestigkeitsprüfungPlaques profilées en fibres ciment - Méthode d'essai de résistance au chocFibre cement profiled sheets - Impact resistance test method91.100.40YODNQLProducts in fibre-reinforced cement91.060.20StreheRoofsICS:Ta slovenski standard je istoveten z:EN 15057:2006SIST EN 15057:2006en01-oktober-2006SIST EN 15057:2006SLOVENSKI
STANDARD



SIST EN 15057:2006



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15057June 2006ICS 91.100.40 English VersionFibre cement profiled sheets - Impact resistance test methodPlaques profilées en fibres ciment - Méthode d'essai derésistance au chocFaserzement-Wellplatten - SchlagfestigkeitsprüfungThis European Standard was approved by CEN on 24 May 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15057:2006: ESIST EN 15057:2006



EN 15057:2006 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.5 4 Symbols and abbreviations.5 5 Product requirements.6 6 Sampling procedure.6 7 Test method for the determination of soft body impact resistance.7 8 Test report.17 Bibliography.18
SIST EN 15057:2006



EN 15057:2006 (E) 3 Foreword This document (EN 15057:2006) has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding”, the secretariat of which is held by IBN/BIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2006, and conflicting national standards shall be withdrawn at the latest by December 2006. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 15057:2006



EN 15057:2006 (E) 4 Introduction Different fibre-cement profiled sheets on the market incorporate additional features to contribute to security during construction of the roof. Fibre-cement profiled sheets have been evaluated for impact resistance by a number of national methods, designed to simulate the impact of accidental falling on the roof. The results from the different existing methods are not directly comparable. This European Standard establishes an agreed method for evaluation of impact resistance of fibre-cement profiled sheet products, based on the experiences obtained over the last number of years in different countries. This is a product standard with no classifications, but this test procedure with different drop heights or number of drops may be used by national regulators to set classifications for roof assemblies. The performance of a roof constructed with these products depends not only on the property of the product as required by this European Standard, but also on the design, construction and performance of the roof as a whole in relation to the environment and conditions of use.
SIST EN 15057:2006



EN 15057:2006 (E) 5 1 Scope This European Standard specifies a soft body impact test method for fibre-cement profiled sheets for roofing. This European Standard applies to fibre-cement profiled sheets conforming to EN 494 and of length greater than or equal to 1,04 m. It applies only to products as delivered. NOTE This European Standard can be applied, after agreement between manufacturer and purchaser, to curved sheets. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 494:2004, Fibre-cement profiled sheets and fittings — Product specification and test methods ISO 7892, Vertical building elements — Impact resistance tests — Impact bodies and general test procedures 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 profiled sheet component the cross section of which consists of corrugations as defined in 3.1 of EN 494:2004 3.2 type test test carried out to demonstrate conformity with the requirements of this European Standard or for approval of a new product and/or when a fundamental change is made in formulation and/or method of manufacture the effects of which cannot be predicted on the basis of previous experience. The test is performed on the delivered product, but is not required for each production batch 3.3 as delivered same condition as the producer intends to supply the product after completing all aspects of the process including maturing and, when appropriate, painting 3.4 span distance between the parallel support axes 3.5 lap (overlap) amount one sheet overlaps another at either the end (end lap) or the side (side lap) 4 Symbols and abbreviations For the purpose of this document, the following symbols and abbreviations apply. E Impact energy in joules SIST EN 15057:2006



EN 15057:2006 (E) 6 h Impact height in metres m Mass of the soft body impactor in kilograms g Acceleration due to gravity in metres per second squared w1 Weight of specimen in grams w2 Weight of dried specimen in grams IPN
I Beam Profiles Normales IPE I Beam Profiles European 5 Product requirements 5.1 Composition Fibre cement profiled sheets shall have a composition according to 5.1.1 of EN 494:2004. 5.2 Appearance and finish Shall be as defined in 5.1.2 of EN 494:2004. 5.3 Criteria for compliance
...