SIST HD 134.5 S1:2004

SLOVENSKI STANDARD
SIST HD 134.5 S1:2004
01-januar-2004
[Not translated]
Radio-frequency connectors - Part 5: R.F. coaxial connectors for cables 96 IEC 60050-
17 and larger (IEC 60169-5:1970)
Hochfrequenz-Steckverbindungen - Teil 5: Koaxiale HF-Steckverbinder für Kabel vom
Typ 96 IEC 60050-17 und größer (IEC 60169-5:1970)
Connecteurs pour fréquences radioélectriques - Partie 5: Connecteurs coaxiaux pour
fréquences radioélectriques pour câbles 96 IEC 60050-17 et plus gros (CEI 60169-
5:1970)
Ta slovenski standard je istoveten z: HD 134.5 S1:1977
ICS:
33.120.30 5DGLRIUHNYHQþQLNRQHNWRUML R.F. connectors
5)
SIST HD 134.5 S1:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST HD 134.5 S1:2004

---------------------- Page: 2 ----------------------

SIST HD 134.5 S1:2004

---------------------- Page: 3 ----------------------

SIST HD 134.5 S1:2004

---------------------- Page: 4 ----------------------

SIST HD 134.5 S1:2004
NORME CEI
INTERNATIONALE IEC
60169-5
INTERNATIONAL
Première édition
STANDARD
First edition
1970-01
Connecteurs pour fréquences radioélectriques
Cinquième partie:
Connecteurs coaxiaux pour fréquences
radioélectriques pour câbles 96 IEC 50-17 et
plus gros
Radio-frequency connectors
Part 5:
R.F.
coaxial connectors for cables 96 IEC 50-17
and larger
© IEC 1970 Droits de reproduction réservés — Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun any form or by any means, electronic or mechanical,
procédé, électronique ou mécanique, y compris la photo- including photocopying and microfilm, without permission in
copie et les microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
N
PRICE CODE
International Electrotechnical Commission
IEC
MemayuaponHaa 3nenrporexHNVecnaa HOMHCCHa
vigueur
Pour prix, voir catalogue en
• •
For price, see current catalogue

---------------------- Page: 5 ----------------------

SIST HD 134.5 S1:2004
ERRATA 1
PUBLICATION 169-5(1970) DE LA CEI IEC PUBLICATION 169-5(1970)
Page 18, paragraphe 14.6 Page 19 5
Sub-clause 14.6
Déplacer la première phrase de la Move first sentence in 4th column to
quatrième colonne à la troisième 3rd column.
colonne.
Page 22, paragraphe 15.2.1 Page 23, Sub-clause 15.2.1
Déplacer le premier alinéa de la
Move the first paragraph in 4th
quatrième colonne à la troisième column to 3rd column.
colonne.
Page 26, première colonne
au lieu de:
Chaleur humide longue durée
lire:
Essai continu de chaleur humide
Février 1971

---------------------- Page: 6 ----------------------

SIST HD 134.5 S1:2004

---------------------- Page: 7 ----------------------

SIST HD 134.5 S1:2004
— 3 —
CONTENTS
Page
FOREWORD 5
5
PREFACE
Clause
1. Scope 7
7
2. IEC type designation
3. Ratings 7
7
4. Climatic category
8
5. Dimensions
10
Gauges 6.
11
7. Survey of patterns
Over-all dimensions 12
8.
19
9. Schedule for type tests

---------------------- Page: 8 ----------------------

SIST HD 134.5 S1:2004
5
INTERNATIONAL ELECTROTECHNICAL COMMISSION
RADIO-FREQUENCY CONNECTORS
Part 5:
R.F. coaxial connectors for cables 96 IEC 50-17 and larger
FOREWORD
I) The formal decisions or agreements of the IEC on technical matters, prepared by Technical Committees on which all
the National Committees having a special interest therein are represented, express, as nearly as possible, an international
consensus of opinion on the subjects dealt with.
2) They have the form of recommendations for international use and they are accepted by the National Committees in
that sense.
3)
In order to promote this international unification, the IEC expresses the wish that all National Committees having as
yet no national rules, when preparing such rules, should use the IEC recommendations as the fundamental basis for
these rules in so far as national conditions will permit.
4)
The desirability is recognized of extending international agreement on these matters through an endeavour to harmonize
national standardization rules with these recommendations in so far as national conditions will permit. The National
Committees pledge their influence towards that end.
5)
The IEC has not laid down any procedure concerning marking as an indication of approval and has no responsibility
when an item of equipment is declared to comply with one of its recommendations.
PREFACE
This Recommendation has been prepared by Sub-Committee 46A, R.F. Cables and their Accessories,
of IEC Technical Committee No. 46, Cables, Wires and Waveguides for Telecommunication Equipment.
It forms Part 5 of the complete Recommendation for Radio-frequency Connectors.
Part 1 : General Requirements and Measuring Methods, with which this Publication must be used,
is issued as IEC Publication 169-1. The specific Recommendation on Coaxial Unmatched Television
Aerial Feeder Connector is issued as IEC Publication 169-2. The Recommendation on Two-pin
Connector for Twin Balanced Aerial Feeders is issued as IEC Publication 169-3. The Recommendation
on R.F. Coaxial Connector for Cables 96 IEC 50-12 is issued as IEC Publication 169-4.
Subsequent relevant specifications for other types of connectors will be issued from time to time
as they become ready.
The first draft of Part 5 was discussed at the meeting held in Aix-les-Bains in 1964. After the meeting
held in Tel-Aviv in 1966, a revised draft was submitted to the National Committees for approval under
the Six Months' Rule in April 1967.
The following countries voted explicitly in favour of publication of Part 5 :
Australia Netherlands
Belgium Norway
Canada Poland
Denmark Sweden
Finland Switzerland
Germany Turkey
Israel United Kingdom
Italy United States of America
Japan

---------------------- Page: 9 ----------------------

SIST HD 134.5 S1:2004
— 7 —
RADIO-FREQUENCY CONNECTORS
Part 5: R.F. Coaxial connectors for cables 96 IEC 50-17 and larger
1. Scope
This Recommendation covers a range of patterns of r.f. coaxial connectors for use with r.f.
cables 96 IEC 50-17 and larger, conforming to IEC Publication 96-2, Radio-frequency Cables,
Part 2 : Relevant Cable Specifications.
2. IEC type designation
Connectors conforming to this Recommendation shall be designated by :
a) the reference to this Recommendation : 169-5 IEC ;
b) a serial number (see Clause 7).
Example :
169-5 IEC 50-17-1 denotes a free pin connector to be used with an r.f. coaxial cable
96 IEC 50-17-1/2/3.
3. Ratings
R.F. connectors, patterns 1 to 5 inclusive and pattern 7, when properly impedance matched, can
be used at frequencies up to 4 000 MHz.
Pattern 8, when properly impedance matched, can be used up to 3 000 MHz.
Voltage at sea level : 8 000 V peak max.
Voltage at 30 000 m altitude : 800 V peak max.
4. Climatic category
Category Temperature range Damp heat, steady state
40/85/21 --40 °C to +85'C 21 days

---------------------- Page: 10 ----------------------

SIST HD 134.5 S1:2004
8
5. Dimensions 5. Dimensions
Les dimensions en millimètres sont les Millimetre dimensions are original di-
dimensions originales. mensions.
5.1 Connecteur à broche 5.1 Pin connector
a
Rr
^ b
Rt c
-",-Rr d -r
^/ ^^^t>
v
h k
FIG. 2. - Détail du filetage.
FIGURE 1 Detail of screw thread.
TABLEAU I
TABLE I
Référence
in
mm Figure Note
Reference
a Tr 50 x 3 Tr 50 x 3 1-2
+ 0.08 0.0032
b 37.00 1.457
1
+
c 29.90 + 0.11 1.177 ± 0.0043 1
d 13.00+0.10 0.512±0.004 1
e 0.394
10.00 _ _
0.036 0.0014 1 1
15.50+1.00 0.610=0.04
f
g 5.05 ± 0.10 0.199 + 0.004
1
0.600. 0.023
_ -
30 0 .012
k
2.80 0.30 0.110 0.012
+
1 5.00 max. 0.197 max.
m 10.00 min. 0.394 min.
p 3.00 0.118
r 1.50 0.059 2
1.870 1
s 47.50
u 50.50 1.992 1
Notes 1.-La concentricité de chaque diamètre avec Notes I.- Each diameter shall be concentric with a
l'axe commun doit être supérieure à t/2, « t» common axis within t/2, where "t" is the
étant la tolérance totale sur le diamètre con-
total tolerance of that diameter.
sidéré.
2. - Tr 50 x 3 indique un filetage trapézoïdal 2. - Tr 50 x 3 indicates Acme screw thread with
ayant un diamètre nominal de 50 mm et un nominal diameter 50 mm (1.97 in) and pitch
pas de 3 mm. 3 mm (0.118 in).

---------------------- Page: 11 ----------------------

SIST HD 134.5 S1:2004
- 9 -
5.2 Connecteur à douille 5.2 Socket connector
FIG. 4. - Détail du filetage.

FIGURE 3 Detail of screw thread.

TABLEAU II TABLE II
Référence
mm in Figure Note
Reference
a Tr 50 x 3 Tr 50 x 3 1-4
b 37.00 1.457 - 1-2
_
0.06 0.0024
c 29.90 0.11 1.177 f 0.0043 1
±
3 1
d 13.00 ± 0.10 0.512 -I- 0.004
e 0.60 +0.30 0.024 +0.012 1
1 .00 +0.04
+ 3
5.90 0.232
g 6.00 min. 0.236 min.
k 14.00 min. 0.551 min.
k 0.67 17.00 min. min.
p 3.00 0.118
r 1.75 0.069 4
s 46.50 1 .831 1
u 50.00 1.969 1
Notes 1. - La concentricité de chaque diamètre avec Notes I. - Each diameter shall be concentric with a
l'axe commun doit être supérieure à t/2, common axis within t/2, where "t" is the
« t » étant la tolérance totale sur le diamètre total tolerance of that diameter.
considéré.
«
2. - La partie b » peut être élastique. 2. - Part "b" may be resilient.
3. - La tolérance de la dimension «f» dépend 3. - The tolerance of dimension "f'' depends on
des dimensions du joint. the gasket.
4. - Tr 50 x 3 indique un filetage trapézoïdal 4. - Tr 50 x 3 indicates Acme screw thread with
ayant un diamètre nominal de 50 mm et un nominal diameter 50 mm (1.97 in) and pitch
pas de 3 mm. 3 mm (0.118 in).

---------------------- Page: 12 ----------------------

SIST HD 134.5 S1:2004
—10-

6. Calibres 6. Gauges

6.1 Calibres pour la mesure de la « résistance de 6.1 Gauges for measuring "contact resistance"

contact » et de la « force de rétention» and "gauge retention force"

FIGURE 5 FIGURE
6
Calibre pour Figure
Matériau
Gauge for Figure Material
Vérification des dimensions Acier poli, rugosité de surface
5
Sizing purpose
Steel, polished, surface roughness
Ra =
0.1 pm (4 pin) max.
Mesure de la résistance de contact
Cuivre au bérillium recouvert de rhodium
6
Measurement of contact resistance Beryllium copper, rhodium plated
Mesure de la force de rétention
Acier poli, rugosité de surface
Measurement of gauge retention 6 Steel, polished, surface roughness
force Ra = 0.1 pm (4 pin) max.
Weight : 1 kg
Masse : 1 kg
6.2 Dimensions du connecteur de référence pour 6.2 Dimensions of standard connector for meas-
la mesure du coefficient de réflexion
uring the reflexion coefficient
The dimensions of the standard connector
Les dimensions du connecteur de référence
shall be the same as those given in Sub-
doivent être les mêmes que celles données
clause 5.2 with the following exceptions:
dans le paragraphe 5.2, à l'exception des
suivantes :
La dimension c est
0.0012
29.91 0.03 mm (1.178 + in)
±
Dimension c shall be
La dimension d est
0.0012 in)
12.99 ± 0.03 mm (0.511 +
Dimension d shall be
La dimension e est
0.03 0.0012
+ +
0.61 mm (0.024 0 iin)n
—o ( Dimension e shall be

---------------------- Page: 13 ----------------------

SIST HD 134.5 S1:2004
— 11 —
7. Revue de modèles 7. Survey of patterns
Les connecteurs donnés ci-dessous peu- Connectors listed below may be used
vent être utilisés avec les câbles pour fréquen- with r.f. cables 96 IEC 50-17-1/2/3.
ces radioélectriques 96 IEC 50-17-1/2/3.
TABLEAU III TABLE III
de type
Classe d'essais Dénomination Dessin Désignation
Test Class Description Type designation
Pattern
f:.i
1 Connecteur libre (droit) I 169-5 IEC 50-17-1
— itil
Free connector (straight)
f^
2 Adaptateur libre (droit) _ 169-5 IEC 50-17-2
Free adaptor (straight)
11111
2 (fixation par 4 I ° ° 169-5 IEC 50-17-3
Adaptateur trous)
Adaptor (4-hole panel-mounting) __ ^
2 Adaptateur (étanche, fixation centrale) I 169-5 IEC 50-17-4
Adaptor (sealed, central panel- +I
mounting) lIl
'^
169-5 IEC 50-17-5
1 Connecteur fixe (fixation par 4 trous) ■ ¢
j. Ih1111
Fixed connector (4-hole panel-
:I
mounting) —
0.
I

O -4
s
3 169-5 IEC 50-17-6
Connecteur fixe (fixation par 4 trou ° °
avec cosse de soudage) __ ■
Fixed connector (4-hole panel-
1111—
II
mounting, with solder tag) y
I Connecteur fixe (fixation par 4 trous 169-5 IEC 50-17-7
avec embout pour ligne coaxiale
rigide)
A^
Fixed connector (4-hole panel-
Il Ill
I
mounting, with entry for rigid 1 ° P
coaxial line)
2 Adaptateur coud _ 169-5 IEC 50-17-8
Angle adaptor
Il
Dans le tableau ci-dessus, les classes applica- In
...