Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air (ISO 12209:2013)

This International Standard specifies the characteristics of outlet connections for gas cylinder valves for compressed breathable air gas cylinders. It states the fundamental requirements for both; the connection and its components and includes basic dimensions. Included in this International Standard are the following connections: - yoke type outlet connection for SCUBA use up to a maximum cylinder working pressure of 232 bar; - threaded type outlet connections up to a maximum cylinder working pressure of 232 bar and 300 bar; and - threaded type outlet connection for SCUBA use up to a maximum cylinder working pressure of 232 bar including adaptor for users to convert into a yoke type outlet. Annex A gives the outlet connection type test procedures. Requirements for cylinder valves (see ISO 10297) are not covered by this International Standard. Requirements for material specifications and gas/material compatibility (see ISO 11114-1 and ISO 11114-2) are not covered by this International Standard.

Gasflaschen - Ausgangsanschlüsse für Gasflaschenventile für verdichtete Atemluft (ISO 12209:2013)

Dieses Dokument legt die Eigenschaften von Ausgangsanschlüssen für Gasflaschenventile für Gasflaschen
für verdichtete Atemluft fest. Es legt die grundlegenden Anforderungen sowohl für den Anschluss als auch für
dessen Einzelteile einschließlich der grundlegenden Maße fest. In diesem Dokument werden die folgenden
Anschlüsse behandelt:
- Bügel-Ausgangsanschluss für SCUBA-Anwendungen bis zu einem maximalen Flaschen-Betriebsdruck
von 232 bar;
- Gewinde-Ausgangsanschlüsse bis zu einem maximalen Flaschen-Betriebsdruck von 232 bar und
300 bar; und
- Gewinde-Ausgangsanschluss für SCUBA-Anwendungen bis zu einem maximalen Flaschen-
Betriebsdruck von 232 bar einschließlich Anwender-Adapter zur Umrüstung auf einen Bügel-Anschluss.
Anhang A enthält die Verfahren der Baumusterprüfung des Ausgangsanschlusses.
Anforderungen für Gasflaschenventile (siehe ISO 10297) sind nicht durch diese Internationale Norm erfasst.

Bouteilles à gaz - Raccords de sortie pour robinets de bouteilles à gaz pour air comprimé respirable (ISO 12209:2013)

L'ISO 12209:2013 spécifie les caractéristiques des raccords de sortie pour les robinets de bouteilles à gaz pour air comprimé respirable. Elle établit les exigences de base pour les raccords et leurs composants, ainsi que leurs dimensions de base. Elle porte sur les raccords suivants:
a) les raccords de sortie à étrier pour une utilisation avec un appareil respiratoire autonome de plongée fonctionnant à une pression de travail maximale pour une bouteille de 232 bar;
b) les raccords de sortie filetés fonctionnant à une pression de travail maximale pour une bouteille de 232 bar et de 300 bar; et
c) les raccords de sortie filetés pour utilisation avec un appareil respiratoire autonome de plongée fonctionnant à une pression de travail maximale pour une bouteille de 232 bar, comprenant un adaptateur pour utilisateur pour conversion en sortie à étrier.
L'Annexe A donne les modes opératoires pour les raccords de sortie.
Les exigences relatives aux robinets des bouteilles (voir l'ISO 10297) ne sont pas traitées dans l'ISO 12209:2013 .
Les exigences pour les spécifications de matériaux et la compatibilité gaz/matériaux (voir l'ISO 11114‑1 et l'ISO 11114‑2) ne sont pas couvertes par l'ISO 12209:2013.

Plinske jeklenke - Izhodni priključki ventila za jeklenke za stisnjeni zrak za dihanje (ISO 12209:2013)

Ta mednarodni standard določa značilnosti izhodnih priključkov ventila za plinske jeklenke za stisnjeni zrak za dihanje. Navaja temeljne zahteve za priključek in njegove sestavne dele ter vključuje osnovne mere. V tem mednarodnem standardu so obravnavani naslednji priključki: – izhodni priključek v obliki prižeme za potapljanje do najvišjega delovnega tlaka jeklenke 232 barov; – navojni izhodni priključek do najvišjega delovnega tlaka jeklenke 232 barov in 300 barov; ter – navojni izhodni priključek za potapljanje do najvišjega delovnega tlaka jeklenke 232 barov, vključno s pretvornikom za uporabnike, da se lahko spremeni v priključek v obliki prižeme. Dodatek A opisuje preskusne postopke za tipe izhodnih priključkov. Zahteve za ventile jeklenk (glej ISO 10297) niso obravnavane v tem mednarodnem standardu. Zahteve za specifikacije materialov in združljivost plina/materiala (glej ISO 11114-1 in ISO 11114-2) niso obravnavane v tem mednarodnem standardu.

General Information

Status
Published
Public Enquiry End Date
19-Jun-2012
Publication Date
17-Nov-2013
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
18-Oct-2013
Due Date
23-Dec-2013
Completion Date
18-Nov-2013

Relations

Buy Standard

Standard
EN ISO 12209:2013
English language
25 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 12209:2013
01-december-2013
1DGRPHãþD
SIST EN ISO 12209-1:2002
SIST EN ISO 12209-2:2002
SIST EN ISO 12209-3:2002
3OLQVNHMHNOHQNH,]KRGQLSULNOMXþNLYHQWLOD]DMHNOHQNH]DVWLVQMHQL]UDN]DGLKDQMH
,62
Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air
(ISO 12209:2013)
Gasflaschen - Ausgangsanschlüsse für Gasflaschenventile für verdichtete Atemluft (ISO
12209:2013)
Bouteilles à gaz - Raccords de sortie pour robinets de bouteilles à gaz pour air comprimé
respirable (ISO 12209:2013)
Ta slovenski standard je istoveten z: EN ISO 12209:2013
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
23.060.40 7ODþQLUHJXODWRUML Pressure regulators
SIST EN ISO 12209:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 12209:2013

---------------------- Page: 2 ----------------------

SIST EN ISO 12209:2013


EUROPEAN STANDARD
EN ISO 12209

NORME EUROPÉENNE

EUROPÄISCHE NORM
September 2013
ICS 23.020.30 Supersedes EN ISO 12209-1:2000, EN ISO 12209-
2:2000, EN ISO 12209-3:2000
English Version
Gas cylinders - Outlet connections for gas cylinder valves for
compressed breathable air (ISO 12209:2013)
Bouteilles à gaz - Raccords de sortie pour robinets de Gasflaschen - Ausgangsanschlüsse für Gasflaschenventile
bouteilles à gaz pour air comprimé respirable (ISO für verdichtete Atemluft (ISO 12209:2013)
12209:2013)
This European Standard was approved by CEN on 17 August 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12209:2013: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 12209:2013
EN ISO 12209:2013 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 12209:2013
EN ISO 12209:2013 (E)
Foreword
This document (EN ISO 12209:2013) has been prepared by Technical Committee ISO/TC 58 "Gas cylinders"
in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the secretariat of which is
held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2014, and conflicting national standards shall be withdrawn at
the latest by March 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 12209-1:2000, EN ISO 12209-2:2000, EN ISO 12209-3:2000.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 12209:2013 has been approved by CEN as EN ISO 12209:2013 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 12209:2013

---------------------- Page: 6 ----------------------

SIST EN ISO 12209:2013
INTERNATIONAL ISO
STANDARD 12209
First edition
2013-09-01
Gas cylinders — Outlet connections
for gas cylinder valves for compressed
breathable air
Bouteilles à gaz — Raccords de sortie pour robinets de bouteilles à
gaz pour air comprimé respirable
Reference number
ISO 12209:2013(E)
©
ISO 2013

---------------------- Page: 7 ----------------------

SIST EN ISO 12209:2013
ISO 12209:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 12209:2013
ISO 12209:2013(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Yoke type outlet connection for SCUBA use up to a maximum cylinder working pressure of
232 bar . 2
5 Threaded type outlet connections up to a maximum cylinder working pressure of 232 bar
and 300 bar . 4
5.1 General requirements . 4
5.2 232 bar threaded outlet connection . 4
5.3 300 bar threaded outlet connection . 8
6 Threaded type valve outlet connection for SCUBA use up to a maximum cylinder working
pressure of 232 bar including adaptor for users to convert into a yoke type outlet .11
7 Marking .15
Annex A (normative) Outlet connection type test procedures .16
Bibliography .18
© ISO 2013 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 12209:2013
ISO 12209:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12209 was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2, Cylinder
fittings, in collaboration with Technical Committee CEN/TC 23, Transportable gas cylinders.
This first edition of ISO 12209 cancels and replaces the first editions of the ISO 12209 series
(ISO 12209-1:2000, ISO 12209-2:2000, ISO 12209-3:2000), which have been technically revised.
The main changes are:
— combination of former three parts of ISO 12209 into a single ISO 12209;
— modification of valve outlet, adaptor and o-ring dimensions; and
— addition of an outlet connection type test procedure in Annex A.
iv © ISO 2013 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 12209:2013
INTERNATIONAL STANDARD ISO 12209:2013(E)
Gas cylinders — Outlet connections for gas cylinder valves
for compressed breathable air
1 Scope
This International Standard specifies the characteristics of outlet connections for gas cylinder valves
for compressed breathable air gas cylinders. It states the fundamental requirements for both; the
connection and its components and includes basic dimensions. Included in this International Standard
are the following connections:
— yoke type outlet connection for SCUBA use up to a maximum cylinder working pressure of 232 bar;
— threaded type outlet connections up to a maximum cylinder working pressure of 232 bar and
300 bar; and
— threaded type outlet connection for SCUBA use up to a maximum cylinder working pressure of
232 bar including adaptor for users to convert into a yoke type outlet.
Annex A gives the outlet connection type test procedures.
Requirements for cylinder valves (see ISO 10297) are not covered by this International Standard.
Requirements for material specifications and gas/material compatibility (see ISO 11114-1 and
ISO 11114-2) are not covered by this International Standard.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual
tolerance indications
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
working pressure
settled pressure of a compressed gas at a uniform reference temperature of 15 °C in a full gas cylinder
[SOURCE: ISO 10286:2007, definition A.2.8]
3.2
SCUBA
self-contained underwater breathing apparatus
3.3
compressed breathable air
gas which has the nominal composition of atmospheric air and is subject to purity level controls
© ISO 2013 – All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 12209:2013
ISO 12209:2013(E)

4 Yoke type outlet connection for SCUBA use up to a maximum cylinder working
pressure of 232 bar
Figure 1 shows an example of the yoke type outlet connection in the assembled state.
The valve outlet and o-ring dimensions including minimum shore hardness (HS) are shown in Figure 2
and given in Table 1 and Table 2.
The exact form of the o-ring groove is the responsibility of the manufacturer providing the connection
passes the outlet connection type test according to Annex A using an o-ring specified in Table 2.
In order to ensure that the yoke does fit over the valve, minimum dimensions are given for the yoke (see
Figure 3 and Table 3).
No outer dimensions are given for the yoke. However, the dimensions shall be chosen such that the yoke
can resist a torque applied via the screw of 20 Nm without visible permanent deformation of the thread
and/or the yoke. In addition, the tests described in Annex A shall be carried out.
Unless otherwise specified, the general tolerances for linear and angular dimensions shall be in
accordance with class m of ISO 2768-1.
Key
1 yoke
2 valve outlet
3 o-ring
4 screw
Figure 1 — Yoke type connection — Assembly drawing
Figure 2 — Valve outlet dimensions
2 © ISO 2013 – All rights reserved

---------------------- Page: 12 ----------------------

SIST EN ISO 12209:2013
ISO 12209:2013(E)

Table 1 — Valve outlet dimensions
Symbol Dimension Tolerance Concentricity
mm mm mm
d to be specified by the manufacturer
1
d 12,67 max. — 0,1
2
d 17,45 max. — 0,1
3
d 18,16 ± 0,08 0,1
4
d 6,3 ± 0,08 0,3
5
l 25,5 max. — not applicable
1
l 1,0 max. — not applicable
2
l 1,98 ± 0,35 not applicable
3
l 28,58 max. — not applicable
4
l 22,5 max. — not applicable
5
α 120 ° — not applicable
Table 2 — O-ring dimensions and properties
“Small type” “Large type”
Symbol/Property
Dimension Tolerance Dimension Tolerance
mm mm mm mm
d 12,42 ± 0,13 12,37 ± 0,13
6
d 1,78 ± 0,08 2,62 ± 0,08
7
HS (90 ± 5) Shore A
NOTE 1 The o-ring dimensions are taken from ISO 3601-1 (same as ASTM D2240) and the hardness is defined in ASTM D2240.
NOTE 2 The “small type” o-ring is commonly referred to as “-014” by most o-ring manufacturers. The “large type” o-ring is
commonly referred to as “-112” by most o-ring manufacturers.
Figure 3 — Yoke dimensions
© ISO 2013 – All rights reserved 3

---------------------- Page: 13 ----------------------

SIST EN ISO 12209:2013
ISO 12209:2013(E)

Table 3 — Yoke dimensions
Dimension Tolerance Dimension Tolerance
Symbol Symbol
mm m
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.