District cooling pipes - Bonded single pipe systems for directly buried cold water networks - Part 2: Factory made fitting assemblies of steel or plastic service pipe, polyurethane thermal insulation and a casing of polyethylene

This document specifies requirements, design and test methods for factory made thermally insulated bonded fitting assemblies for directly buried district cooling distribution systems, comprising a service fitting from DN 15 to DN 1200, rigid polyurethane foam insulation and a casing of polyethylene.
The fitting assembly may also include the following additional elements: measuring wires, spacers and diffusion barriers.
This document covers the following fitting assemblies: bend, tee, reducer, cap, single use compensator and anchor.
This document applies only to insulated fitting assemblies, for continuous operation with water at various
temperatures (1 to 30)°C and a maximum operation pressure of 25 bar. The design is based on an expected service life with continuous operation of a minimum 50 years.

Fernkühlungsrohre - Werkmäßig gedämmte Verbundmantelrohrsysteme für direkt erdverlegte Fernkältenetze - Teil 2: Werkmäßig gedämmte Verbund-Formstücke bestehend aus Stahl-oder Plastik-Mediumrohr, Polyurethan-Wärmedämmung und Außenmantel aus Polyethylen

Fernkälterohre — Einzelrohr-Verbundsysteme für direkt erdverlegte Fernkältenetze — Teil 2: Werkmäßig gefertigte Verbundformstücke, bestehend aus Stahl- oder Kunststoff-Mediumrohr, einer Wärmedämmung aus Polyurethan und einer Ummantelung aus Polyethylen

Réseaux d’eau glacée - Systèmes bloqués de tuyaux pour les réseaux d'eau glacée enterrés directement - Partie 2 : Assemblages de raccords manufacturés pour tubes de service en acier ou en plastique, isolation thermique en polyuréthane et tube de protection en polyéthylène

Le présent document spécifie les exigences, la conception et les méthodes d’essai pour des assemblages manufacturés de raccords bloqués préisolés thermiquement pour les réseaux de distribution d’eau glacée urbains enterrés directement, constitués d’un raccord de DN 15 à DN 1200, d’une isolation en mousse de polyuréthane rigide et d’un tube de protection en polyéthylène.
Le raccord préisolé peut également comprendre les éléments supplémentaires suivants : des câbles de mesure, des entretoises et les barrières anti diffusion.
Le présent document couvre les raccords préisolés suivants : coude, té, réducteur, bouchon, compensateur à usage unique et pièce d’ancrage.
Le présent document ne concerne que les assemblages de raccords préisolés, destinés à un usage continu avec de l’eau à diverses températures (de 1 °C à 30 °C) et à une pression de service maximale de 25 bar.
La conception est fondée sur une durée utile prévue en fonctionnement continu d’au moins 50 ans

Cevi za daljinsko hlajenje - Spojeni enocevni sistemi za neposredno vkopana hladnovodna omrežja - 2. del: Tovarniško izdelana armatura iz jeklene ali plastične delovne cevi, poliuretanske toplotne izolacije in polietilenskega plašča

General Information

Status
Published
Public Enquiry End Date
30-Sep-2020
Publication Date
12-Sep-2021
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
09-Sep-2021
Due Date
14-Nov-2021
Completion Date
13-Sep-2021

Buy Standard

Standard
EN 17415-2:2021
English language
34 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 17415-2:2020 - BARVE
English language
34 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 17415-2:2021
01-november-2021
Cevi za daljinsko hlajenje - Spojeni enocevni sistemi za neposredno vkopana
hladnovodna omrežja - 2. del: Tovarniško izdelana armatura iz jeklene ali plastične
delovne cevi, poliuretanske toplotne izolacije in polietilenskega plašča
District cooling pipes - Bonded single pipe systems for directly buried cold water
networks - Part 2: Factory made fitting assemblies of steel or plastic service pipe,
polyurethane thermal insulation and a casing of polyethylene
Fernkühlungsrohre - Werkmäßig gedämmte Verbundmantelrohrsysteme für direkt
erdverlegte Fernkältenetze - Teil 2: Werkmäßig gedämmte Verbund-Formstücke
bestehend aus Stahl-oder Plastik-Mediumrohr, Polyurethan-Wärmedämmung und
Außenmantel aus Polyethylen
Réseaux d’eau glacée - Systèmes bloqués de tuyaux pour les réseaux d'eau glacée
enterrés directement - Partie 2 : Assemblages de raccords manufacturés pour tubes de
service en acier ou en plastique, isolation thermique en polyuréthane et tube de
protection en polyéthylène
Ta slovenski standard je istoveten z: EN 17415-2:2021
ICS:
23.040.99 Drugi sestavni deli za Other pipeline components
cevovode
SIST EN 17415-2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 17415-2:2021

---------------------- Page: 2 ----------------------
SIST EN 17415-2:2021


EN 17415-2
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2021
EUROPÄISCHE NORM
ICS 23.040.99
English Version

District cooling pipes - Bonded single pipe systems for
directly buried cold water networks - Part 2: Factory made
fitting assemblies of steel or plastic service pipe,
polyurethane thermal insulation and a casing of
polyethylene
Réseaux d'eau glacée - Systèmes bloqués de tuyaux Fernkälterohre - Einzelrohr-Verbundsysteme für
pour les réseaux d'eau glacée enterrés directement - direkt erdverlegte Fernkältenetze - Teil 2: Werkmäßig
Partie 2 : Assemblages de raccords manufacturés pour gefertigte Verbundformstücke, bestehend aus Stahl-
tubes de service en acier ou en plastique, isolation oder Kunststoff-Mediumrohr, einer Wärmedämmung
thermique en polyuréthane et tube de protection en aus Polyurethan und einer Ummantelung aus
polyéthylène Polyethylen
This European Standard was approved by CEN on 18 July 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17415-2:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 17415-2:2021
EN 17415-2:2021 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Requirements . 7
4.1 General requirements . 7
4.2 Service pipe parts . 7
4.3 Casing . 15
4.4 Polyurethane (PUR) foam thermal insulation . 15
4.5 Fitting assemblies . 15
4.6 Surveillance system . 19
5 Test methods . 19
5.1 General . 19
5.2 Test specimens . 20
5.3 Steel service pipe parts . 20
5.4 Plastics service pipe fittings . 21
5.5 Casing . 22
5.6 Polyurethane (PUR) foam thermal insulation . 22
5.7 Fitting assemblies . 22
5.8 Surveillance system . 23
6 Marking . 23
6.1 General . 23
6.2 Service pipe . 23
6.3 Casing . 24
6.4 Fitting assembly . 24
Annex A (informative) Guidelines for inspection and testing . 25
Annex B (informative) Procedures for casing welding . 29
Annex C (informative) Waste treatment and recycling . 33
Bibliography . 34

2

---------------------- Page: 4 ----------------------
SIST EN 17415-2:2021
EN 17415-2:2021 (E)
European foreword
This document (EN 17415-2:2021) has been prepared by Technical Committee CEN/TC 107 “Prefabricated
district heating and district cooling pipe system”, the secretariat of which is held by DS.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2022, and conflicting national standards shall be withdrawn
at the latest by March 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards body. A
complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedonia,
Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
3

---------------------- Page: 5 ----------------------
SIST EN 17415-2:2021
EN 17415-2:2021 (E)
Introduction
Factory made bonded single pipe systems for directly buried district cooling networks are of common
technical usage. In order to ensure quality including product-related service life, to ensure safety in use,
economical energy usage and to facilitate comparability in the market, CEN/TC 107 decided to set up
standards for these products.
This document is one of a series of standards which form several parts of EN 17415, District cooling pipes –
Bonded single pipe systems for directly buried cold water networks:
— Part 1: Factory made pipe assembly of steel or plastic service pipe, polyurethane thermal insulation and a
casing of polyethylene;
— Part 2: Factory made fitting assemblies of steel or plastic service pipe, polyurethane thermal insulation and
a casing of polyethylene (this document);
— Part 3: Factory made steel valve assembly for steel or plastic service pipe, polyurethane thermal insulation
and a casing of polyethylene.
The other standards from CEN/TC 107 covering this subject are:
— EN 17414-1, District cooling pipes — Factory made flexible pipe systems — Part 1: Classification, general
requirements and test methods;
— EN 17414-2, District cooling pipes — Factory made flexible pipe systems — Part 2: Bonded system with
plastic service pipes; requirements and test methods;
— EN 17414-3, District cooling pipes — Factory made flexible pipe systems — Part 3: Non bonded system
with plastic service pipes; requirements and test methods;
1
— EN XXXXX-1 , District cooling pipes — Design and installation of thermal insulated bonded single and twin
pipe systems for directly buried cold water networks — Part 1: Design;
1
, District cooling pipes — Design and installation of thermal insulated bonded single and twin
— EN XXXXX-2
pipe systems for directly buried cold water networks — Part 2: Installation;
— EN 489-1, District heating pipes — Bonded single and twin pipe systems for buried hot water networks —
Part 1: Joint casing assemblies and thermal insulation for hot water networks in accordance with
EN 13941-1;
— EN 14419, District heating pipes — Bonded single and twin pipe systems for directly buried hot water
networks — Surveillance systems.
Waste management and recycling of materials is dealt with in Annex C.

1
Under development.
4

---------------------- Page: 6 ----------------------
SIST EN 17415-2:2021
EN 17415-2:2021 (E)
1 Scope
This document specifies requirements, design and test methods for factory made thermally insulated
bonded fitting assemblies for directly buried district cooling distribution systems, comprising a service
fitting from DN 15 to DN 1200, rigid polyurethane foam insulation and a casing of polyethylene.
The fitting assembly can also include the following additional elements: measuring wires, spacers and
diffusion barriers.
This document covers the following fitting assemblies: bend, tee, reducer, cap and anchor.
This document applies only to insulated fitting assemblies, for continuous operation with water at various
temperatures (1 to 30) °C and a maximum operation pressure of 25 bar.
The design is based on an expected service life with continuous operation of a minimum 50 years.
NOTE An expected service life of 50 years presupposes that treated water is used.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 10204, Metallic products - Types of inspection documents
EN 10253-2, Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection
requirements
EN 12201-2, Plastics piping systems for water supply, and for drainage and sewerage under pressure —
Polyethylene (PE) — Part 2: Pipes
EN 12201-3, Plastics piping systems for water supply, and for drainage and sewerage under pressure —
Polyethylene (PE) — Part 3: Fittings
EN 12201-5, Plastics piping systems for water supply, and for drainage and sewerage under pressure -
Polyethylene (PE) - Part 5: Fitness for purpose of the system
EN 12814-1, Testing of welded joints of thermoplastics semi-finished products - Part 1: Bend test
EN 13018, Non-destructive testing - Visual testing - General principles
EN 13067, Plastics welding personnel - Qualification of welders - Thermoplastics welded assemblies
EN 13941-1, District heating pipes - Design and installation of thermal insulated bonded single and twin pipe
systems for directly buried hot water networks - Part 1: Design
EN 13941-2, District heating pipes - Design and installation of thermal insulated bonded single and twin pipe
systems for directly buried hot water networks - Part 2: Installation
EN 14419, District heating pipes - Bonded single and twin pipe systems for buried hot water networks -
Surveillance systems
EN 14870-1, Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline
transportation systems - Part 1: Induction bends (ISO 15590-1)
EN 17248, District heating and district cooling pipe systems - Terms and definitions
5

---------------------- Page: 7 ----------------------
SIST EN 17415-2:2021
EN 17415-2:2021 (E)
EN 17415-1:2020, District cooling pipes - Bonded single pipe systems for directly buried cold water networks -
Part 1: Factory made pipe assembly of steel or plastic service pipe, polyurethane thermal insulation and a
casing of polyethylene
EN ISO 3452-1, Non-destructive testing - Penetrant testing - Part 1: General principles (ISO 3452-1)
EN ISO 5579, Non-destructive testing - Radiographic testing of metallic materials using film and X- or gamma
rays - Basic rules (ISO 5579)
EN ISO 5817, Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded)
- Quality levels for imperfections (ISO 5817)
EN ISO 8501-1, Preparation of steel substrates before application of paints and related products - Visual
assessment of surface cleanliness - Part 1: Rust grades and preparation grades of uncoated steel substrates and
of steel substrates after overall removal of previous coatings (ISO 8501-1)
EN ISO 9606-1, Qualification testing of welders - Fusion welding - Part 1: Steels (ISO 9606-1)
EN ISO 9692-1:2013, Welding and allied processes - Types of joint preparation - Part 1: Manual metal arc
welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels
(ISO 9692-1:2013)
EN ISO 9934-1, Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1)
EN ISO 10675-1, Non-destructive testing of welds - Acceptance levels for radiographic testing - Part 1: Steel,
nickel, titanium and their alloys (ISO 10675-1)
EN ISO 11666, Non-destructive testing of welds - Ultrasonic testing - Acceptance levels (ISO 11666)
EN ISO 14732, Welding personnel - Qualification testing of welding operators and weld setters for mechanized
and automatic welding of metallic materials (ISO 14732)
EN ISO 15607, Specification and qualification of welding procedures for metallic materials - General rules
(ISO 15607)
EN ISO 16810, Non-destructive testing - Ultrasonic testing - General principles (ISO 16810)
EN ISO 17636-1, Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray techniques
with film (ISO 17636-1)
EN ISO 17636-2, Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray techniques
with digital detectors (ISO 17636-2)
EN ISO 17637, Non-destructive testing of welds - Visual testing of fusion-welded joints (ISO 17637)
EN ISO 17638, Non-destructive testing of welds - Magnetic particle testing (ISO 17638)
EN ISO 17640, Non-destructive testing of welds - Ultrasonic testing - Techniques, testing levels, and assessment
(ISO 17640)
EN ISO 23277, Non-destructive testing of welds - Penetrant testing - Acceptance levels (ISO 23277)
EN ISO 23278, Non-destructive testing of welds - Magnetic particle testing - Acceptance levels (ISO 23278)
6

---------------------- Page: 8 ----------------------
SIST EN 17415-2:2021
EN 17415-2:2021 (E)
3 Terms and definitions
For the purposes of this document the terms and definitions given in EN 17248 and EN 17415-1 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at https://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
4 Requirements
4.1 General requirements
Unless otherwise specified, the requirements shall be valid for each single measurement.
For information on suitable guidelines for inspection of factory made fitting assemblies, see Annex A.
4.2 Service pipe parts
4.2.1 Steel service pipe parts
4.2.1.1 General
The material of the fitting steel parts shall be certified in accordance with EN 10204. If traceability on
material is required by the end user it shall be specified at the time of ordering. Corresponding material
certificates shall be delivered to the end user if specified at the time of ordering.
4.2.1.2 Specification
The fitting steel material shall be in accordance with the steel grade specification in EN 17415-1.
All steel pipes and components used for manufacturing of pipe assemblies under the scope of this document
shall as a minimum be delivered to the manufacturer with an inspection certificate 3.1 according to
EN 10204. The inspection certificate shall on request be passed on to the client who orders the fitting
assemblies.
In case a material related inspection certificate 3.1 according to EN 10204 is required by the client who
orders the fitting assemblies, this request shall be given whilst placing the order with the manufacturer of
the fitting assemblies.
NOTE Any later request for provision of such documentation could be too late and possibly can't be met by the
manufacturer, since the manufacturer needs to organize the assignment of 3.1 certificates to pipes and part of pipes
before starting the production.
4.2.1.3 Wall thickness and diameter
All components shall be designed for a minimum operating pressure of 16 bar.
If the fitting assemblies are intended to be used in situations with pressures higher than 16 bar, extra
calculations will be necessary.
The minimum nominal wall thickness of all components shall prior to processing be at least the same as for
the service pipes in accordance with EN 17415-1.
The nominal diameter, the outside diameter, the tolerances on the diameter of the pipe ends and the wall
thickness shall be the same as for the service pipes in accordance with EN 17415-1.
Subject to design considerations other wall thicknesses than those given in EN 17415-1 may be used, but in
no case shall these be less than the minima indicated in EN 17415-1.
7

---------------------- Page: 9 ----------------------
SIST EN 17415-2:2021
EN 17415-2:2021 (E)
All components shall be designed in accordance with EN 13941-1 for the actions and stresses that normally
occur during the service life of the fitting assembly (or of the component).
4.2.1.4 Bends
4.2.1.4.1 Butt welding bends
The dimensions shall be in accordance with EN 10253-2 with the exception that the bend radius shall
be ≥ 1,5 times the outer diameter.
4.2.1.4.2 Cold formed bends
Cold formed bends shall be produced from seamless pipe or longitudinal welded pipes. At cold formed bends
made of longitudinal welded pipes the weld bead shall be welded to factor V = 1 (calculation stress = 100 %).
After bending, the minimum wall thickness of the bent pipe shall be not less than 85 % of the wall thickness
of the straight pipe (see EN 17415-1).
The maximum ovality in the bent area shall not exceed 6 %.
The formula for the calculation of the ovality is:
D − D
( )
s max s min
o ×100 (1)
D
s
where
o is the ovality, in %;
D is the maximum outside diameter;
s max
D is the minimum outside diameter in the same cross section in the bended area;
s min
D is the specified outside diameter.
s
There shall be no folding in the bent area. Waves may be accepted, when the maximum height between
trough and crest of the wave does not exceed 25 % of the nominal wall thickness of the bent pipe.
4.2.1.4.3 Hot-formed bends
For hot-formed bends manufactured from straight pipes by means of inductive heating (induction bends), no
heat treatment is necessary as far as this method is applied with unalloyed or low-alloyed steel with
[Mo] < 0,65 %. Hot-formed bends shall be supplied in conformity with EN 14870-1.
If for the bending other heating methods are applied, heat treatment following the bending of the pipes is
required.
If a hot-formed bend has to be made from line pipe, this shall be specified to the pipe manufacturer at the
time of ordering so that the pipe manufacturer can take this into account when selecting the (chemical)
composition of the pipe material and the welding filler material.
It is recommended to determine per batch, diameter, wall thickness and bend radius, through mechanical
testing, that the bends comply with the applicable material specifications. It is customary that a
representative bend or an (additional) section of a bend of adequate length will be manufactured during the
production process and that 10 % of the bends will be tested.
8
=

---------------------- Page: 10 ----------------------
SIST EN 17415-2:2021
EN 17415-2:2021 (E)
4.2.1.4.4 Tolerances of bending angles
The deviation from the nominal bending angle shall not exceed the tolerances given in Table 1.
Table 1 — Deviations from nominal bending angle
Nominal diameter Deviation
of service pipe
≤ DN 200 ± 2,0 °
> DN 200 ± 1,0 °
4.2.1.5 T-pieces
4.2.1.5.1 Forged T-pieces
The wall thickness t and t (see EN 10253-2) shall be at least the same as those for the straight pipes
1
(see EN 17415-1). All other dimensions shall be in accordance with EN 10253-2.
4.2.1.5.2 Welded T-pieces
Welded T-pieces shall be manufactured by drawing a collar on which the branch pipe is welded or by
welding the branch pipe directly to the main pipe. The wall thickness of the collar shall be at least the same
as that for the branch pipe (see EN 17415-1). The collar shall be drawn opposite the welding seam in the
main pipe. When using branch pipe directly welded to the main pipe, compensating (reinforcement) plates
may be used according to EN 13941-1 requirements.
4.2.1.5.3 Tolerances of angles between branch pipes and main pipes
The branch pipes shall be perpendicular to the main pipes within a tolerance of ± 2,0 °.
4.2.1.6 Reducers
Reducers shall be in accordance with EN 10253-2, except for the wall thicknesses t and t1 (see EN 10253-2)
which shall be at least the same as for the straight pipes (see EN 17415-1) to be welded to the fittings.
4.2.1.7 Anchors
The anchors shall be marked with the information concerning maximum loads for which the construction
was designed and calculated. The lifetime of the system shall not be influenced by the anchors construction.
4.2.1.8 Caps
Caps (dished ends) shall be in accordance with EN 10253-2 and comply with the requirements of
EN 13941-1.
4.2.1.9 Fusion welding of steel fittings
4.2.1.9.1 Filler material
Filler material shall after welding have mechanical characteristics comparable with the parent metal.
4.2.1.9.2 Welding process
All types of fusion welding are acceptable but arc welding with covered electrodes and gas-shielded metal-
arc welding are preferred. The welding process shall be specified and approved in accordance with
EN ISO 15607.
The method of approval may be chosen by the manufacturer.
Fittings of wall thickness ≥ 5,6 mm shall be welded in more than one pass.
9

---------------------- Page: 11 ----------------------
SIST EN 17415-2:2021
EN 17415-2:2021 (E)
4.2.1.9.3 Preparation for welding
Pipe ends shall be prepared in accordance with the welding procedure used. When using covered electrodes
or gas-shielded metal-arc welding, pipe ends and fittings with equal wall thickness shall be prepared in
accordance with EN ISO 9692-1. See Table 2.
Table 2 of this document is derived from EN ISO 9692-1:2013, Table 1 and gives the relation between wall
thickness and reference number.
Table 2 — Preparation of ends of pipes and fittings for weldings according to EN ISO 9692-1:2013
Symbol Type of preparation Wall thickness t of steel service Reference to
pipe fittings or fitting end EN ISO 9692-1:2013, Table
1
II Square preparation t < 3 mm 1.2.1
V Single V preparation 3 mm ≤ t ≤ 10 mm 1.3
V Single Y preparation t > 10 mm 1.5
with broad root face
NOTE Symbols are in accordance with EN ISO 2553.
Pipe ends and fittings with different wall thicknesses shall be prepared and adapted for misalignment in
accordance with Table 3 and Figure 1 of this document.
Table 3 — Adaptation of misalignment and difference in wall thickness

Adaptation Required action
Misalignment
Misalignment h ≤ 0,3 t, max. 1 mm Figure 1 detail A
Misalignment 1 mm < h ≤ 10 mm  Adaptation of pipe ends
Misalignment h > 10 mm Extra fitting Extra prepared steel fitting minimum
length
The seam spacing shall be such that
the heat-affected zones do not overlap
or interact. A spacing of 100 mm or
more is recommended. The minimum
spacing is 50 mm
Difference in wall thickness
Differences in wall thickness: t' ≤ 1,5 t Figure 1 detail B Adaptation of thicker wall t'
n
Differences in wall thickness: t' > 1,5 t Figure 1 detail C Adaptation of both sides
n
10

---------------------- Page: 12 ----------------------
SIST EN 17415-2:2021
EN 17415-2:2021 (E)


Key
h misalignment
tn smallest wall thickness
t’ largest wall thickness
Figure 1 — Misalignment, difference in wall thickness and steel service pipe end preparation, in
accordance with EN 13941-2
When manufacturing T-pieces with the branch pipe welded directly to the main pipe, preparations shall
comply with Figure 2.
11

---------------------- Page: 13 ----------------------
SIST EN 17415-2:2021
EN 17415-2:2021 (E)

Key
a section X at crotch of right angle branch c section Y at flank of unequal branch. Ratios of
diameters > 2/3
b section Y at flank of unequal branch. Ratios of d section W at flank of equal branch
diameters ≤ 2/3
Figure 2 — Preparation of set-on branches
4.2.1.9.4 Inspection of welds
When visual surface examination is carried out, it shall be in accordance with 5.3.1. The examinations
include a check of surface, internal, joint geometry and multiple imperfections. The welding shall comply
with “quality level B” of EN ISO 5817.
When a leak-tightness test is carried out in accordance with 5.3.2 or 5.3.3, the welds shall fulfil the
conditions stated there.
When non-destructive test is carried out, it shall be in accordance with 5.3.4. The weld shall comply with
“quality level B” of EN ISO 5817.
4.2.1.9.5 Competence of the welder
The welder shall have a valid certificate according to EN ISO 9606-1 for the techniques, material groups,
dimension ranges and welding position concerned. Welding personnel operating mechanized welding
equipment shall be qualified in accordance with EN ISO 14732.
12

---------------------- Page: 14 ----------------------
SIST EN 17415-2:2021
EN 17415-2:2021 (E)
4.2.1.10 Surface co
...

SLOVENSKI STANDARD
oSIST prEN 17415-2:2020
01-september-2020
Cevi za daljinsko hlajenje - Spojeni enocevni sistemi za neposredno vkopana
hladnovodna omrežja - 2. del: Tovarniško izdelan cevni sestav iz jeklene ali
plastične delovne cevi, poliuretanske toplotne izolacije in polietilenskega plašča
District cooling pipes - Bonded single pipe systems for directly buried cold water
networks - Part 2: Factory made fitting assemblies of steel or plastic service pipe,
polyurethane thermal insulation and a casing of polyethylene
Fernkühlungsrohre - Werkmäßig gedämmte Verbundmantelrohrsysteme für direkt
erdverlegte Fernkältenetze - Teil 2: Werkmäßig gedämmte Verbund-Formstücke
bestehend aus Stahl-oder Plastik-Mediumrohr, Polyurethan-Wärmedämmung und
Außenmantel aus Polyethylen
Réseaux d’eau glacée - Systèmes bloqués de tuyaux pour les réseaux d'eau glacée
enterrés directement - Partie 2 : Assemblages de raccords manufacturés pour tubes de
service en acier ou en plastique, isolation thermique en polyuréthane et tube de
protection en polyéthylène
Ta slovenski standard je istoveten z: prEN 17415-2
ICS:
23.040.99 Drugi sestavni deli za Other pipeline components
cevovode
oSIST prEN 17415-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 17415-2:2020

---------------------- Page: 2 ----------------------
oSIST prEN 17415-2:2020


DRAFT
EUROPEAN STANDARD
prEN 17415-2
NORME EUROPÉENNE

EUROPÄISCHE NORM

July 2020
ICS 23.040.99
English Version

District cooling pipes - Bonded single pipe systems for
directly buried cold water networks - Part 2: Factory made
fitting assemblies of steel or plastic service pipe,
polyurethane thermal insulation and a casing of
polyethylene
Réseaux d'eau glacée - Systèmes bloqués de tuyaux Fernkühlungsrohre - Werkmäßig gedämmte
pour les réseaux d'eau glacée enterrés directement - Verbundmantelrohrsysteme für direkt erdverlegte
Partie 2 : Assemblages de raccords manufacturés pour Fernkältenetze - Teil 2: Werkmäßig gedämmte
tubes de service en acier ou en plastique, isolation Verbund-Formstücke bestehend aus Stahl-oder Plastik-
thermique en polyuréthane et tube de protection en Mediumrohr, Polyurethan-Wärmedämmung und
polyéthylène Außenmantel aus Polyethylen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 107.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 17415-2:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 17415-2:2020
prEN 17415-2:2020 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Requirements . 7
4.1 General requirements . 7
4.2 Service pipe parts . 7
4.3 Casing . 15
4.4 Polyurethane (PUR) foam thermal insulation . 15
4.5 Fitting assemblies . 15
4.6 Surveillance system . 19
5 Test methods . 19
5.1 General . 19
5.2 Test specimens . 19
5.3 Steel service pipe parts . 20
5.4 Plastics service pipe fittings . 21
5.5 Casing . 21
5.6 Polyurethane (PUR) foam thermal insulation . 21
5.7 Fitting assemblies . 21
5.8 Surveillance system . 22
6 Marking . 22
6.1 General . 22
6.2 Service pipe . 23
6.3 Casing . 23
6.4 Fitting assembly . 23
6.5 Single use compensators . 24
Annex A (informative) Guidelines for inspection and testing . 25
Annex B (informative) Procedures for casing welding . 29
Annex C (informative) Waste treatment and recycling . 33
Bibliography . 34
2

---------------------- Page: 4 ----------------------
oSIST prEN 17415-2:2020
prEN 17415-2:2020 (E)
European foreword
This document (prEN 17415-2:2020) has been prepared by Technical Committee CEN/TC 107
“Prefabricated district heating and district cooling pipe system”, the secretariat of which is held by DS.
This document is currently submitted to the CEN Enquiry.
3

---------------------- Page: 5 ----------------------
oSIST prEN 17415-2:2020
prEN 17415-2:2020 (E)
Introduction
Factory made bonded single pipe systems for directly buried district cooling networks are of common
technical usage. In order to ensure quality including product-related service life, to assure safety in use,
economical energy usage and to facilitate comparability in the market, CEN/TC 107 decided to set up
standards for these products.
This document is one of a series of standards which form several parts of EN 17415, District cooling pipes –
Bonded single pipe systems for directly buried cold water networks:
— Part 1: Factory made pipe assembly of steel or plastic service pipe, polyurethane thermal insulation and a
1)
casing of polyethylene (this document) ;
— Part 2: Factory made fitting assemblies of steel or plastic service pipe, polyurethane thermal insulation and
1)
a casing of polyethylene ;
— Part 3: Factory made steel valve assembly for steel or plastic service pipe, polyurethane thermal insulation
1)
and a casing of polyethylene ;
The other standards from CEN/TC 107 covering this subject are:
— EN 17414-1, District cooling pipes – Factory made flexible pipe systems – Part 1: Classification, general
1)
requirements and test methods ;
— EN 17414-2, District cooling pipes – Factory made flexible pipe systems – Part 2: Bonded system with
1)
plastic service pipes; requirements and test methods ;
— EN 17414-3, District cooling pipes – Factory made flexible pipe systems – Part 3: Non bonded system with
1)
plastic service pipes; requirements and test methods ;
— EN ZZZZZ-1, District cooling pipes – Design and installation of thermal insulated bonded single and twin
1)
pipe systems for directly buried cold water networks – Part 1: Design ;
— EN ZZZZZ-2, District cooling pipes – Design and installation of thermal insulated bonded single and twin
1)
pipe systems for directly buried cold water networks – Part 2: Installation ;
— EN 489-1, District heating pipes – Bonded single and twin pipe systems for buried hot water networks –
Part 1: Joint casing assemblies and thermal insulation for hot water networks in accordance with
EN 13941-1;
— EN 14419, District heating pipes – Bonded single and twin pipe systems for directly buried hot water
networks – Surveillance systems;

1) Under development.
4

---------------------- Page: 6 ----------------------
oSIST prEN 17415-2:2020
prEN 17415-2:2020 (E)
1 Scope
This document specifies requirements, design and test methods for factory made thermally insulated
bonded fitting assemblies for directly buried district cooling distribution systems, comprising a service
fitting from DN 15 to DN 1200, rigid polyurethane foam insulation and a casing of polyethylene.
The fitting assembly can also include the following additional elements: measuring wires, spacers and
diffusion barriers.
This document covers the following fitting assemblies: bend, tee, reducer, cap, single use compensator and
anchor.
This document applies only to insulated fitting assemblies, for continuous operation with water at various
temperatures (1 to 30) °C and a maximum operation pressure of 25 bar.
The design is based on an expected service life with continuous operation of a minimum 50 years.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 10204, Metallic products — Types of inspection documents
EN 10253-2, Butt-welding pipe fittings — Part 2: Non alloy and ferritic alloy steels with specific inspection
requirements
EN 12201-2, Plastics piping systems for water supply, and for drainage and sewerage under pressure –
Polyethylene (PE) – Part 2: Pipes
EN 12201-3, Plastics piping systems for water supply, and for drainage and sewerage under pressure –
Polyethylene (PE) – Part 3: Fittings
EN 12201-5, Plastics piping systems for water supply, and for drainage and sewerage under pressure –
Polyethylene (PE) – Part 5: Fitness for purpose of the system
EN 12814-1, Testing of welded joints of thermoplastics semi-finished products — Part 1: Bend test
EN 13018, Non-destructive testing —Visual testing — General principles
EN 13067, Plastics welding personnel – Qualification testing of welders – Thermoplastics welded assemblies
EN 14419, District heating pipes – Bonded single and twin pipe systems for directly buried hot water networks
– Surveillance systems
EN 14870-1, Petroleum and natural gas industries — Induction bends, fittings and flanges for pipeline
transportation systems — Part 1: Induction bends (ISO 15590-1:2009 modified)
EN 17415-1:2020, District cooling pipes — Bonded single pipe systems for directly buried cold water
networks — Part 1: Factory made pipe assembly of steel or plastic service pipe, polyurethane thermal insulation
2)
and a casing of polyethylene

2) Under development.
5

---------------------- Page: 7 ----------------------
oSIST prEN 17415-2:2020
prEN 17415-2:2020 (E)
EN 13941-1, District heating pipes - Design and installation of thermal insulated bonded single and twin pipe
3)
systems for directly buried hot water networks - Part 1: Design
EN 13941-2, District heating pipes - Design and installation of thermal insulated bonded single and twin pipe
3
)
systems for directly buried hot water networks - Part 2: Installation
EN ISO 3452-1, Non-destructive testing — Penetrant testing — Part 1: General principles (ISO 3452-1)
EN ISO 5579, Non-destructive testing — Radiographic testing of metallic materials using film and X- or gamma
rays - Basic rules (ISO 5579)
EN ISO 5817, Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding
excluded) — Quality levels for imperfections (ISO 5817)
EN ISO 8501-1, Preparation of steel substrates before application of paints and related products — Visual
assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates
and of steel substrates after overall removal of previous coatings (ISO 8501-1)
EN ISO 9606-1, Qualification testing of welders — Fusion welding — Part 1: Steels (ISO 9606-1)
EN ISO 9692-1:2013, Welding and allied processes — Types of joint preparation — Part 1: Manual metal arc
welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels
(ISO 9692-1:2013)
EN ISO 9934-1, Non-destructive testing — Magnetic particle testing — Part 1: General principles (ISO 9934-1)
EN ISO 10675-1, Non-destructive testing of welds — Acceptance levels for radiographic testing — Part 1: Steel,
nickel, titanium and their alloys (ISO 10675-1)
EN ISO 11666, Non-destructive testing of welds — Ultrasonic testing — Acceptance levels (ISO 11666)
EN ISO 13760, Plastics pipes for the conveyance of fluids under pressure – Miner’s rule – Calculation method for
cumulative damage (ISO 13760)
EN ISO 14732, Welding personnel — Qualification testing of welding operators and weld setters for
mechanized and automatic welding of metallic materials (ISO 14732)
EN ISO 15607, Specification and qualification of welding procedures for metallic materials — General rules
(ISO 15607)
EN ISO 16810, Non-destructive testing — Ultrasonic testing — General principles (ISO 16810)
EN ISO 17636-1, Non-destructive testing of welds — Radiographic testing — Part 1: X- and gamma-ray
techniques with film (ISO 17636-1)
EN ISO 17636-2, Non-destructive testing of welds — Radiographic testing — Part 2: X- and gamma-ray
techniques with digital detectors (ISO 17636-2)
EN ISO 17637, Non-destructive testing of welds — Visual testing of fusion-welded joints (ISO 17637)
EN ISO 17638, Non-destructive testing of welds — Magnetic particle testing (ISO 17638)

3)
Under development.
6

---------------------- Page: 8 ----------------------
oSIST prEN 17415-2:2020
prEN 17415-2:2020 (E)
EN ISO 17640, Non-destructive testing of welds — Ultrasonic testing — Techniques, testing levels, and
assessment (ISO 17640)
EN ISO 23277, Non-destructive testing of welds — Penetrant testing — Acceptance levels (ISO 23277)
EN ISO 23278, Non-destructive testing of welds — Magnetic particle testing — Acceptance levels (ISO 23278)
3 Terms and definitions
For the purposes of this document the terms and definitions given in EN 17415-1 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
4 Requirements
4.1 General requirements
Unless otherwise specified, the requirements shall be valid for each single measurement.
For information on suitable guidelines for inspection of factory made fitting assemblies, see Annex A.
4.2 Service pipe parts
4.2.1 Steel service pipe parts
4.2.1.1 General
The material of the fitting steel parts shall be certified in accordance with EN 10204. If traceability on
material is required by the end user it shall be specified at the time of ordering. Corresponding material
certificates shall be delivered to the end user if specified at the time of ordering.
4.2.1.2 Specification
The fitting steel material shall be in accordance with the steel grade specification in EN 17415-1.
All steel pipes and components used for manufacturing of pipe assemblies under the scope of this document
shall as a minimum be delivered to the manufacturer with an inspection certificate 3.1 according to
EN 10204. The inspection certificate shall on request be passed on to the client who orders the fitting
assemblies.
In case a material related inspection certificate 3.1 according to EN 10204 is required by the client who
orders the fitting assemblies, this request shall be given whilst placing the order with the manufacturer of
the fitting assemblies.
Any later request for provision of such documentation could be too late and possibly can't be met by the
manufacturer, since the manufacturer has to organize the assignment of 3.1 certificates to pipes and part of
pipes before starting the production.
4.2.1.3 Wall thickness and diameter
According to the scope of this document, all components shall be designed for a minimum operating
pressure of 16 bar.
If the fitting assemblies are intended to be used in situations with pressures higher than 16 bar, extra
calculations will be necessary.
7

---------------------- Page: 9 ----------------------
oSIST prEN 17415-2:2020
prEN 17415-2:2020 (E)
The minimum nominal wall thickness of all components shall prior to processing be at least the same as for
the service pipes in accordance with EN 17415-1.
The nominal diameter, the outside diameter, the tolerances on the diameter of the pipe ends and the wall
thickness shall be the same as for the service pipes in accordance with EN 17415-1.
Subject to design considerations other wall thicknesses than those given in EN 17415-1 may be used, but in
no case shall these be less than the minima indicated in EN 17415-1.
4)
All components shall be designed in accordance with EN 13941-1 for the actions and stresses that
normally occur during the service life of the fitting assembly (or of the component).
4.2.1.4 Bends
4.2.1.4.1 Butt welding bends
The dimensions shall be in accordance with EN 10253-2 with the exception that the bend radius shall
be ≥ 1,5 times the outer diameter.
4.2.1.4.2 Cold formed bends
Cold formed bends shall be produced from seamless pipe or longitudinal welded pipes. At cold formed bends
made of longitudinal welded pipes the weld bead shall be welded to factor V = 1 (calculation stress = 100 %).
After bending, the minimum wall thickness of the bent pipe shall be not less than 85 % of the wall thickness
of the straight pipe (see EN 17415-1).
The maximum ovality in the bent area shall not exceed 6 %.
The formula for the calculation of the ovality is:
D − D
( )
s max s min
o ×100 (1)
D
s
where
o is the ovality, in %;
D is the maximum outside diameter;
s max
D is the minimum outside diameter in the same cross section in the bended
s min
area;
D is the specified outside diameter.
s
There shall be no folding in the bent area. Waves may be accepted, when the maximum height between
trough and crest of the wave does not exceed 25 % of the nominal wall thickness of the bent pipe.
4.2.1.4.3 Hot-formed bends
For hot-formed bends manufactured from straight pipes by means of inductive heating (induction bends), no
heat treatment is necessary as far as this method is applied with unalloyed or low-alloyed steel with
[Mo] < 0,65 %. Hot-formed bends shall be supplied in conformity with EN 14870-1.
If for the bending other heating methods are applied, heat treatment following the bending of the pipes is
required.

4)
Under development.
8
=

---------------------- Page: 10 ----------------------
oSIST prEN 17415-2:2020
prEN 17415-2:2020 (E)
If a hot-formed bend has to be made from line pipe, this shall be specified to the pipe manufacturer at the
time of ordering so that the pipe manufacturer can take this into account when selecting the (chemical)
composition of the pipe material and the welding filler material.
It is recommended to determine per batch, diameter, wall thickness and bend radius, through mechanical
testing, that the bends comply with the applicable material specifications. It is customary that a
representative bend or an (additional) section of a bend of adequate length will be manufactured during the
production process and that 10 % of the bends will be tested.
4.2.1.4.4 Tolerances of bending angles
The deviation from the nominal bending angle shall not exceed the tolerances given in Table 1.
Table 1 — Deviations from nominal bending angle
Nominal diameter of Deviation
service pipe
≤ DN 200 ±2,0°
> DN 200 ±1,0°
4.2.1.5 T-pieces
4.2.1.5.1 Forged T-pieces
The wall thickness t and t (see EN 10253-2) shall be at least the same as those for the straight pipes (see
1
EN 17415-1). All other dimensions shall be in accordance with EN 10253-2.
4.2.1.5.2 Welded T-pieces
Welded T-pieces shall be manufactured by drawing a collar on which the branch pipe is welded or by
welding the branch pipe directly to the main pipe. The wall thickness of the collar shall be at least the same
as that for the branch pipe (see EN 17415-1). The collar shall be drawn opposite the welding seam in the
main pipe. When using branch pipe directly welded to the main pipe, compensating (reinforcement) plates
5)
may be used according to EN 13941-1 requirements.
4.2.1.5.3 Tolerances of angles between branch pipes and main pipes
The branch pipes shall be perpendicular to the main pipes within a tolerance of ± 2,0°.
4.2.1.6 Reducers
Reducers shall be in accordance with EN 10253-2, except for the wall thicknesses t and t (see EN 10253-2)
1
which shall be at least the same as for the straight pipes (see EN 17415-1) to be welded to the fittings.
4.2.1.7 Anchors
The anchors shall be marked with the information concerning maximum loads for which the construction
was designed and calculated. The lifetime of the system shall not be influenced by the anchors construction.
4.2.1.8 Single use compensators
5)
A single use compensator shall comply with the requirements of EN 13941-1 .
4.2.1.9 Caps
Caps (dished ends) shall be in accordance with EN 10253-2 and comply with the requirements of EN 13941-
5)
1 .

5)
Under development.
9

---------------------- Page: 11 ----------------------
oSIST prEN 17415-2:2020
prEN 17415-2:2020 (E)
4.2.1.10 Fusion welding of steel fittings
4.2.1.10.1 Filler material
Filler material shall after welding have mechanical characteristics comparable with the parent metal.
4.2.1.10.2 Welding process
All types of fusion welding are acceptable but arc welding with covered electrodes and gas-shielded metal-
arc welding are preferred. The welding process shall be specified and approved in accordance with
EN ISO 15607.
The method of approval may be chosen by the manufacturer.
Fittings of wall thickness ≥ 5,6 mm shall be welded in more than one pass.
4.2.1.10.3 Preparation for welding
Pipe ends shall be prepared in accordance with the welding procedure used. When using covered electrodes
or gas-shielded metal-arc welding, pipe ends and fittings with equal wall thickness shall be prepared in
accordance with EN ISO 9692-1.
Table 2 of this document is derived from EN ISO 9692-1:2013, Table 1 and gives the relation between wall
thickness and reference number.
Table 2 — Preparation of ends of pipes and fittings for weldings according to EN ISO 9692-1:2013
Symbol Type of preparation Wall thickness t of steel service Reference to
pipe fittings or fitting end EN ISO 9692-1:2013, Table 1
II Square preparation t < 3 mm 1.2.1
V Single V preparation 3 mm ≤ t ≤ 10 mm 1.3
Y Single Y preparation with t > 10 mm 1.5
broad root face
NOTE Symbols are in accordance with EN ISO 2553.
Pipe ends and fittings with different wall thicknesses shall be prepared and adapted for misalignment in
accordance with Table 3 and Figure 1 of this document.
Table 3 — Adaptation of misalignment and difference in wall thickness
 Adaptation Required action
Misalignment
Misalignment h ≤ 0,3 t, max. 1 mm Figure 1 detail A
Misalignment 1 mm < h ≤ 10 mm  Adaptation of pipe ends
Misalignment h > 10 mm Extra fitting Extra prepared steel fitting minimum
length.
The seam spacing shall be such that the
heat-affected zones do not overlap or
interact. A spacing of 100 mm or more is
recommended. The minimum spacing is
50 mm.
Difference in wall thickness
Differences in wall thickness: t' ≤ 1,5 tn Figure 1 detail B Adaptation of thicker wall t'
Differences in wall thickness: t' > 1,5 tn Figure 1 detail C Adaptation of both sides
10

---------------------- Page: 12 ----------------------
oSIST prEN 17415-2:2020
prEN 17415-2:2020 (E)

Key
h misalignment
tn smallest wall thickness
t’ largest wall thickness
Figure 1 — Misalignment, difference in wall thickness and steel service pipe end preparation, in
6)
accordance with EN 13941-2
When manufacturing T-pieces with the branch pipe welded directly to the main pipe, preparations shall
comply with Figure 2.

6)
Under development.
11

---------------------- Page: 13 ----------------------
oSIST prEN 17415-2:2020
prEN 17415-2:2020 (E)

Key
a Section X at crotch of right angle branch c Section Y at flank of unequal branch. Ratios of
b Section Y at flank of unequal branch. Ratios of  diameters > 2/3
 diameters ≤ 2/3 d Section W at flank of equal branch
Figure 2 — Preparation of set-on branches
4.2.1.10.4 Inspection of welds
When visual surface examination is carried out, it shall be in accordance with 5.3.1. The examinations
include a check of surface, internal, joint geometry and multiple imperfections. The welding shall comply
with “quality level B” of EN ISO 5817.
When a leak-tightness test is carried out in accordance with 5.3.2 or 5.3.3, the welds shall fulfil the
conditions stated there.
When non-destructive test is carried out, it shall be in accordance with 5.3.4. The weld shall comply with
“quality level B” of EN ISO 5817.
4.2.1.10.5 Competence of the welder
The welder shall have a valid certificate according to EN ISO 9606-1 for the techniques, material groups,
dimension ranges and welding position concerned. Welding personnel operating mechanized welding
equipment shall be qualified in accordance with EN ISO 14732.
12

---------------------- Page: 14 ----------------------
oSIST prEN 17415-2:2020
prEN 17415-
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.