Cathodic protection - Competence levels of cathodic protection persons - Basis for certification scheme (ISO 15257:2017)

This International Standard defines five levels of competence for persons acting in the field of cathodic protection, including survey, design, installation, testing and maintenance. It specifies a framework for establishing these competence levels and their minimum requirements.
Competence levels apply to each of the following application sectors:
- on-land metallic structures;
- marine metallic structures;
-  reinforced concrete structures;
- inner surfaces of metallic container structures.
This International Standard defines the requirements to be used for establishing a certification scheme as
defined in ISO/IEC 17024. This certification scheme is detailed in normative Annexes A, B and C.
Info: CEN/TC 219 developed EN 15257:2006 which is now being adopted by ISO/TC 156 with some changes from the original EN document. The ISO Work Item was registered by ISO/TC 156 as ISO lead Vienna Agreement Work Item but was not approved within CEN/TC 219 as an active CEN/TC 219 Work Item under ISO lead Vienna Agreement which is required for CEN/TC 219 to actively vote in parallel.
CEN/TC 219 approved the NWIP as an ISO lead Vienna Agreement Parallel Work Item.

Kathodischer Korrosionsschutz - Qualifikationsgrade von mit kathodischem Korrosionsschutz befassten Personen - Grundlage für ein Zertifizierungsverfahren (ISO 15257:2017)

Protection cathodique - Niveaux de compétence des personnes en protection cathodique - Base pour un dispositif particulier de certification (ISO 15257:2017)

ISO 15257:2017 définit cinq niveaux de compétence (détaillés à l'Article 4) pour les personnes travaillant dans le domaine de la protection cathodique (PC), incluant l'étude préalable, la conception, l'installation, le contrôle, la maintenance, ainsi que les progrès scientifiques en protection cathodique. Il spécifie un cadre pour l'établissement de ces niveaux de compétence, ainsi que les exigences minimales correspondantes.
Les niveaux de compétence s'appliquent à chacun des secteurs d'application suivants:
-      les structures métalliques terrestres;
-      les structures métalliques en mer;
-      les structures en béton armé;
-      les surfaces intérieures des structures métalliques contenant un électrolyte.
Ces secteurs d'application sont décrits en détail à l'Article 5.
ISO 15257:2017 spécifie les exigences à utiliser pour établir un dispositif particulier de certification comme défini dans l'ISO/IEC 17024. Il n'est pas obligatoire d'appliquer tous les niveaux et/ou tous les secteurs d'application. Ce dispositif particulier de certification est décrit en détail dans les Annexes A, B et C.

Katodna zaščita - Stopnje usposobljenosti in certifikacija osebja za katodno zaščito - Osnova za shemo certificiranja (ISO 15257:2017)

Ta mednarodni standard določa pet stopenj usposobljenosti in certificiranja osebja, ki deluje na področju katodne zaščite, vključno s pregledom, projektiranjem, namestitvijo, preskušanjem in vzdrževanjem. Določa okvir za vzpostavitev teh stopenj usposobljenosti in certificiranja ter minimalne zahteve. Stopnje usposobljenosti in certificiranja se uporabljajo v vsakem od naslednjih sektorjev: – kovinske strukture na kopnem; – pomorske kovinske strukture; – strukture iz armiranega betona; – notranje površine iz kovinskih oklopnih struktur. Ta mednarodni standard določa zahteve, ki se uporabljajo za vzpostavljanje sheme certificiranja, kot določa standard ISO/IEC 17024. Ta shema certificiranja je podrobno opisana v dodatkih A, B in C. Informacije: Tehnični odbor CEN/TC 219 je razvil standard EN 15257:2006, ki ga sedaj sprejema tehnični odbor ISO/TC 156 z nekaterimi spremembami izvirnega dokumenta EN. Tehnični odbor ISO/TC 156 je registriral delovni element ISO kot delovni element ISO v skladu z dunajskim sporazumom, vendar ga tehnični odbor CEN/TC 219 ni odobril kot aktivni delovni element CEN/TC 219 v skladu z dunajskim sporazumom, kar je potrebno za vzporedno aktivno glasovanje tehničnega odbora CEN/TC 219. Tehnični odbor CEN/TC 219 je odobril NWIP kot delovni element ISO v skladu z dunajskim sporazumom.

General Information

Status
Published
Public Enquiry End Date
09-Mar-2015
Publication Date
10-Aug-2017
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
02-Aug-2017
Due Date
07-Oct-2017
Completion Date
11-Aug-2017

Relations

Buy Standard

Standard
EN ISO 15257:2017
English language
39 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15257:2017
01-september-2017
1DGRPHãþD
SIST EN 15257:2007
.DWRGQD]DãþLWD6WRSQMHXVSRVREOMHQRVWLLQFHUWLILNDFLMDRVHEMD]DNDWRGQR
]DãþLWR2VQRYD]DVKHPRFHUWLILFLUDQMD ,62
Cathodic protection - Competence levels of cathodic protection persons - Basis for
certification scheme (ISO 15257:2017)
Kathodischer Korrosionsschutz - Qualifikationsgrade von mit kathodischem
Korrosionsschutz befassten Personen - Grundlage für ein Zertifizierungsverfahren (ISO
15257:2017)
Protection cathodique - Niveaux de compétence des personnes en protection cathodique
- Base pour un dispositif particulier de certification (ISO 15257:2017)
Ta slovenski standard je istoveten z: EN ISO 15257:2017
ICS:
03.100.30 Vodenje ljudi Management of human
resources
25.220.40 Kovinske prevleke Metallic coatings
SIST EN ISO 15257:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15257:2017

---------------------- Page: 2 ----------------------

SIST EN ISO 15257:2017


EN ISO 15257
EUROPEAN STANDARD

NORME EUROPÉENNE

June 2017
EUROPÄISCHE NORM
ICS 77.060 Supersedes EN 15257:2006
English Version

Cathodic protection - Competence levels of cathodic
protection persons - Basis for certification scheme (ISO
15257:2017)
Protection cathodique - Niveaux de compétence des Kathodischer Korrosionsschutz - Qualifikationsgrade
personnes en protection cathodique - Base pour un von mit kathodischem Korrosionsschutz befassten
dispositif particulier de certification (ISO 15257:2017) Personen - Grundlage für ein Zertifizierungsverfahren
(ISO 15257:2017)
This European Standard was approved by CEN on 15 February 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15257:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15257:2017
EN ISO 15257:2017 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 15257:2017
EN ISO 15257:2017 (E)
European foreword
This document (EN ISO 15257:2017) has been prepared by Technical Committee ISO/TC 156
"Corrosion of metals and alloys" in collaboration with Technical Committee CEN/TC 219 “Cathodic
protection” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2017, and conflicting national standards
shall be withdrawn at the latest by December 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 15257:2006.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 15257:2017 has been approved by CEN as EN ISO 15257:2017 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 15257:2017

---------------------- Page: 6 ----------------------

SIST EN ISO 15257:2017
INTERNATIONAL ISO
STANDARD 15257
First edition
2017-05
Cathodic protection — Competence
levels of cathodic protection persons
— Basis for a certification scheme
Protection cathodique — Niveaux de compétence des personnes
en protection cathodique — Base pour un dispositif particulier de
certification
Reference number
ISO 15257:2017(E)
©
ISO 2017

---------------------- Page: 7 ----------------------

SIST EN ISO 15257:2017
ISO 15257:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 15257:2017
ISO 15257:2017(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Levels of competence . 3
4.1 General . 3
4.2 Level 1, cathodic protection data collector (or tester) . 3
4.3 Level 2, cathodic protection technician . 3
4.4 Level 3, cathodic protection senior technician . 3
4.5 Level 4, cathodic protection specialist. 4
4.6 Level 5, cathodic protection expert . 4
4.7 Designation of competence levels . 4
5 Application sectors . 4
5.1 General . 4
5.2 On-land metallic structures . 5
5.3 Marine metallic structures. 5
5.4 Reinforced concrete structures . 6
5.5 Inner surfaces of metallic structures containing an electrolyte . 6
6 Requirements for competence of persons at various levels and for various
applications sectors . 6
6.1 General . 6
6.2 Knowledge required for all application sectors and all levels . 7
6.3 Tasks to be fulfilled in all application sectors for Levels 1 to 4 . 7
6.4 Specific tasks for on-land metallic structures application sector for Levels 1 to 4.10
6.5 Specific tasks for marine metallic structures application sector for Levels 1 to 4 .12
6.6 Specific tasks for reinforced concrete structures application sector for Levels 1 to 4 .14
6.7 Specific tasks for inner surfaces of metallic structures application sector for Levels
1 to 4 .15
6.8 Requirements for Level 5 CP persons .16
Annex A (normative) Certification scheme: Eligibility for competence assessment for Levels
1 to 4 .17
Annex B (normative) Certification scheme: Examination and assessment .22
Annex C (normative) Certification scheme: Certificate, validity, re-certification,
transition periods.27
Bibliography .30
© ISO 2017 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 15257:2017
ISO 15257:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 156, Corrosion of metals and alloys.
iv © ISO 2017 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 15257:2017
ISO 15257:2017(E)

Introduction
This document enables the competence of cathodic protection (CP) persons carrying out cathodic
protection survey, design, installation, testing and maintenance work to be defined and verified.
The relevant application sectors concern on-land metallic structures, marine metallic structures,
reinforced concrete structures and the inner surfaces of metallic structures containing an electrolyte.
Demonstration of competence is possible by certification. This document offers a certification scheme
in accordance with ISO/IEC 17024.
In preparation of Clauses 4, 5 and 6, a detailed job task analysis (JTA) was undertaken by consensus
of the experts in ISO TC 156. This JTA was then subject to review by international experts during
the ISO enquiry process. It is considered that Clauses 4, 5 and 6 constitute a rigorous JTA. The JTA is
largely based on similar work performed by CEN/TC 219, which produced EN 15257, which has been in
widespread use since 2007.
© ISO 2017 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 15257:2017

---------------------- Page: 12 ----------------------

SIST EN ISO 15257:2017
INTERNATIONAL STANDARD ISO 15257:2017(E)
Cathodic protection — Competence levels of cathodic
protection persons — Basis for a certification scheme
1 Scope
This document defines five levels of competence (detailed in Clause 4) for persons working in the field
of cathodic protection (CP), including survey, design, installation, testing, maintenance and advancing
the science of cathodic protection. It specifies a framework for establishing these competence levels
and their minimum requirements.
Competence levels apply to each of the following application sectors:
— on-land metallic structures;
— marine metallic structures;
— reinforced concrete structures;
— inner surfaces of metallic structures containing an electrolyte.
These application sectors are detailed in Clause 5.
This document specifies the requirements to be used for establishing a certification scheme as
defined in ISO/IEC 17024. It is not mandatory to apply all of the levels and/or application sectors. This
certification scheme is detailed in Annexes A, B and C.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO/IEC 17024, Conformity assessment — General requirements for bodies operating certification of persons
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8044 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
3.1
application sector
particular section of industry or technology where specialized cathodic protection survey, design,
installation, testing and maintenance practices are used or the science of cathodic protection is
advanced, requiring specific sector-related knowledge, skill, equipment or training (3.13)
3.2
assessment committee
group appointed by the certification body which reviews applications and examination results and
determines compliance with the requirements for CP certifications offered by the certification body
© ISO 2017 – All rights reserved 1

---------------------- Page: 13 ----------------------

SIST EN ISO 15257:2017
ISO 15257:2017(E)

3.3
CP person
cathodic protection person
person who devotes a regular and significant percentage of professional activity to the practical
application of cathodic protection within one or more of the application sectors (3.1)
3.4
competence
ability to apply knowledge and skill to achieve intended results
Note 1 to entry: Within the scope of this document, the ability of CP persons (3.3) means to apply defined
knowledge and defined skills and undertake defined tasks at specific levels and specific application sectors (3.1).
3.5
complex structure
system comprising the structure to be protected connected to one or more foreign electrodes and/or
crossing multiple connected electrodes or passing close or through steel-reinforced concrete
EXAMPLE Steel in concrete and earthing installations are examples of foreign electrodes.
3.6
examination centre
place for the examination of competence (3.4) in cathodic protection
Note 1 to entry: The centre includes testing facilities to simulate the conditions that normally exist in real
cathodic protection of operating industrial structures for a given application sector (3.1).
3.7
examiner
person with relevant technical and personal qualifications, and competent to conduct and/or score an
examination
3.8
industrial cathodic protection experience
practice in the applicable cathodic protection techniques and application sector(s) (3.1) concerned,
which leads to the required skill and knowledge
3.9
significant interruption
period of time in which a CP person (3.3) has not practised the duties or undertaken training (3.13)
corresponding to their level of competence (3.4) within an application sector (3.1)
Note 1 to entry: A significant interruption comprises a continuous period in excess of 1,5 years or two or more
periods for a total time exceeding 3 years during the validity of the certificate.
3.10
simple CP system
simple cathodic protection system
cathodic protection system with no design constraints due to external electrical influences, foreign
structure interaction or unpredictable electrolyte changes where the design follows identified and
defined, auditable procedural steps as developed by a person certificated to Level 4
3.11
technical instruction
written description, method statement or work instruction stating the precise steps to be followed
in a cathodic protection survey, design, installation, testing or maintenance activity to an established
standard, code, specification or cathodic protection procedure
3.12
technical report
written report intended to transmit engineering information of a complex, analytical nature
2 © ISO 2017 – All rights reserved

---------------------- Page: 14 ----------------------

SIST EN ISO 15257:2017
ISO 15257:2017(E)

3.13
training
theoretical and practical instructions given in conformity to a pre-established programme in order to
furnish or increase the knowledge and the ability of CP persons (3.3) in cathodic protection activities
3.14
training centre
centre where training (3.13) of CP persons (3.3) is carried out
Note 1 to entry: The training centre includes demonstration and testing facilities to simulate the electrical
conditions that normally exist in real cathodic protection of operating industrial structures for a given application
sector (3.1).
4 Levels of competence
4.1 General
The competence of CP persons shall be classified in one or more of the following levels, depending on
their competence in particular application sectors.
A detailed description of the requirements of competence is given in Clause 6.
Each defined level of competence shall include also the competence of the corresponding lower levels.
4.2 Level 1, cathodic protection data collector (or tester)
Level 1 CP persons shall be competent to collect CP performance data of simple CP systems and perform
other basic CP tasks in accordance with technical instructions and procedures produced by Level 3 or
higher persons and record the data to a format produced by Level 3, or higher persons and under their
responsibility. Level 1 persons shall not be responsible for analysing the data. Level 1 persons shall
understand the fundamentals of the measurements that they are required to undertake, the common
causes of errors in these measurements and the related safety issues. The measurements shall include
routine system function measurements, as well as a limited number of specific measurements to
determine the performance effectiveness of CP systems.
4.3 Level 2, cathodic protection technician
In addition to the competencies for Level 1 CP persons, Level 2 CP persons shall be competent to
undertake a range of CP measurement, inspection and supervisory activities in accordance with
technical instructions and procedures produced by Level 3 or higher persons, and collate and classify
the data under their responsibility.
Level 2 persons shall have knowledge of the fundamentals of electricity, corrosion, coatings, CP and
measurement techniques, safety issues and applicable standards related to CP.
Level 2 persons shall be competent to check the calibration validity of the CP measuring and testing
equipment, supervise and perform inspection and testing during installation of CP systems and carry
out routine maintenance work on CP systems.
Level 2 persons shall not be responsible for the choice of test method, the technique to be used,
preparing the technical instructions or the interpretation of test results.
4.4 Level 3, cathodic protection senior technician
In addition to the competencies for Level 2 persons, Level 3 persons shall have knowledge of the
general principles of corrosion and CP, the principles of electricity, the significance of coatings and their
influence on CP and a detailed knowledge of CP test procedures and safety issues.
© ISO 2017 – All rights reserved 3

---------------------- Page: 15 ----------------------

SIST EN ISO 15257:2017
ISO 15257:2017(E)

Level 3 persons shall understand and be competent to perform CP tasks according to established or
recognized procedures. They shall be competent to carry out and supervise all Level 1 and Level 2
duties, provide guidance for persons at Level 1 and Level 2. They shall be competent to prepare technical
instructions for all CP persons of lower-level competence and assess all data collected from these tasks.
4.5 Level 4, cathodic protection specialist
In addition to the competences for Level 3 persons, Level 4 persons shall have detailed knowledge
of corrosion theory, principles of electricity, CP design, installation, commissioning, testing and
performance evaluation, including systems affected by interfering conditions. They shall have
competence in establishing testing and performance criteria where none are otherwise available. They
shall have a general familiarity with CP in all application sectors.
They shall be competent to design CP systems including those where no pre-set parameters or
procedural steps exist. They shall be competent to define the guidelines for specifying, designing and
monitoring CP systems. They shall be competent to consider technical and safety aspects.
They shall be competent to prepare technical instructions for all CP persons of lower-level competence
and assess all data collected from these tasks.
In all of these activities, Level 4 persons are not required to be supervised by Level 5 or other persons.
4.6 Level 5, cathodic protection expert
In addition to the competencies for Level 4 persons, Level 5 CP persons shall have advanced the state
of the art of CP by scientific work and peer-reviewed publications and shall have made a marked and
original contribution to the science or practice of corrosion control by CP.
Level 5 persons shall have all the competences required in Clause 6 for Level 4 persons in at least one
sector and shall have detailed knowledge of CP and a range of competences in all sectors. They shall have
in at least one of the sectors an established and mature reputation as a CP specialist at the highest level.
Level 5 persons shall undertake a range of high-level activities such as management of R&D projects,
publications in technical or scientific journals or books, lectures at congresses or training courses,
participation in standardization or technical committees, lead in the development of new technology or
new applications, editing scientific journals and/or other activities as described in B.5.
It is not precluded for Level 4 persons to perform any of the tasks attributed to Level 5.
It is not a requirement that certification bodies, examination centres or training centres utilize Level 5
CP persons in the operation and management of their activities.
4.7 Designation of competence levels
Levels 1 to 5 are the definitive terms. The terms cathodic protection tester, cathodic protection
technician, cathodic protection senior technician, cathodic protection specialist and cathodic protection
expert are used above in an indicative purpose only.
5 Application sectors
5.1 General
Any of the following application sectors shall be used in the establishment of competence levels of
CP persons. For each of the application sectors (see 5.2 to 5.5), national and international specific
standards may apply.
In addition to the specific knowledge for each application sector, a common core of knowledge is
required.
4 © ISO 2017 – All rights reserved

---------------------- Page: 16 ----------------------

SIST EN ISO 15257:2017
ISO 15257:2017(E)

5.2 On-land metallic structures
The following topics are relevant to this application sector:
— CP general principles and specific applications in soils and waters;
— CP measurement techniques;
— protection against corrosion by stray current from direct current systems;
— interference from alternating and direct current;
— the relevance of touch potentials.
This application sector includes, for example, the following:
a) buried onshore pipelines;
b) sections of onshore pipelines crossing rivers, lakes or short lengths of sea;
c) landfalls of offshore pipelines protected by an onshore CP system;
d) buried tanks;
e) bottoms (external side) of above-ground tanks;
f) complex structures (see 3.5);
g) well casings;
h) buried plant modules.
5.3 Marine metallic structures
The following topics are relevant to this application sector:
— CP general principles;
— CP measurement techniques;
— specific applications in seawater and marine sediments.
This application sector includes, for example, the following:
a) ships (external hulls and ballast tanks filled with sea water);
b) CP measurement techniques;
c) fixed offshore structures (platforms, jackets, monopiles, offshore windfarms, tension leg
platforms, etc.);
d) floating structures [buoys, semi-submersible platforms, floating production storage and offloading
structures (FPSO)];
e) underwater structures (well heads, manifolds, piping);
f) coastal and offshore pipelines, risers;
g) landfall of offshore pipelines protected by an offshore CP system;
h) harbour facilities, piers, jetties and lock gates.
© ISO 2017 – All rights reserved 5

---------------------- Page: 17 ----------------------

SIST EN ISO 15257:2017
ISO 15257:2017(E)

5.4 Reinforced concrete structures
The following topics ar
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.