SIST EN 4406:2009

SLOVENSKI STANDARD
SIST EN 4406:2009
01-junij-2009
Aeronavtika - Barve in laki - Dvokomponentni poliuretanski premaz, ki se suši pri
sobni temperaturi - Odpornost proti obrabi
Aerospace series - Paints and varnishes - Two component cold curing polyurethane
coating - Abrasion resistant
Luft- und Raumfahrt - Beschichtungsstoffe - Zweikomponenten-Polyurethan-
Deckbeschichtung, kalthärtend - Abriebfest
Série aérospatiale - Peintures et vernis - Peinture de finition polyuréthane à deux
composants polymérisant à température ambiante - Résistance à l'abrasion
Ta slovenski standard je istoveten z: EN 4406:2006
ICS:
49.040 Prevleke in z njimi povezani Coatings and related
postopki, ki se uporabljajo v processes used in aerospace
letalski in vesoljski industriji industry
SIST EN 4406:2009 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 4406:2009

---------------------- Page: 2 ----------------------

SIST EN 4406:2009
EUROPEAN STANDARD
EN 4406
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2006
ICS 49.040

English Version
Aerospace series - Paints and varnishes - Two component cold
curing polyurethane coating - Abrasion resistant
Série aérospatiale - Peintures et vernis - Peinture de finition Luft- und Raumfahrt - Anstrichstoffe - Zweikomponenten
polyuréthane à deux composants polymérisant à Polyurethan-Decklack Kalthärtend - Abriebfest
température ambiante - Résistance à l'abrasion
This European Standard was approved by CEN on 21 July 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4406:2006: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 4406:2009
EN 4406:2006 (E)
Contents Page
Foreword.3
Introduction .4
1 Scope .4
2 Normative references .4
3 Definitions .5
4 Classification.5
5 Batch release and qualification testing.5

2

---------------------- Page: 4 ----------------------

SIST EN 4406:2009
EN 4406:2006 (E)
Foreword
This document (EN 4406:2006) has been prepared by the Aerospace and Defence Industries Association of
Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2007, and conflicting national standards shall be withdrawn at the
latest by April 2007.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
Switzerland and the United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST EN 4406:2009
EN 4406:2006 (E)
Introduction
This standard has been prepared in accordance with TR 7000-9.
1 Scope
This standard specifies the requirements for a two component polyurethane, abrasion resistant coating
available in a range of colours and levels of gloss, to be applied over a primer for aerospace applications
offering resistance to wear on sliding surfaces and resistance to impact from solid particles.
The properties specified in this standard are obtained on defined aluminium alloy test pieces prepared in
accordance with EN 3837 Procedure A and ISO 3270 and painted with primer to EN 2435. The ability of the
material to be used for a specific application (e.g. alternative substrate, alternative primer, specific drying
conditions etc.) shall be determined by supplementary tests to confirm that the requirements of this standard
are met.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1513, Paints and varnishes — Examination and preparation of samples for testing.
ISO 3270, Paints and varnishes and their raw materials — Temperatures and humidities for conditioning and
testing.
ISO 3696, Water for analytical laboratory use — Specification and test methods.
EN 2334, Aerospace series — Chromic-sulphuric acid pickle of aluminium and aluminium alloys.
1)
EN 2379, Aerospace series — Fluids for assessment of non-metallic materials.
EN 2434 (all parts), Aerospace series — Paints and varnishes — Two component cold curing polyurethane
1)
finish.
EN 2435 (all parts), Aerospace series — Paints and varnishes — Corrosion resistant chromated two component
1)
cold curing primer.
EN 3837, Aerospace series — Paints and varnishes — Nature and method for surface preparation of test
1)
pieces in aluminium alloys.
1)
EN 3840, Aerospace series — Paints and varnishes — Technical specification.
TR 7000-9, Aerospace series — Non-metallic materials — Rules for the drafting and presentation of material
2)
standards — Part 9: Paints and varnishes.
STANAG 4477, Specification for paints and paint systems, resistant to chemical agents and decontaminants,
for the protection of aerospace military equipment.

1) Published as ASD Pre-standard at the date of publication of this standard.
2) Published as ASD Technical Report at the date of publication of this standard.
4

---------------------- Page: 6 ----------------------

SIST EN 4406:2009
EN 4406:2006 (E)
3 Definitions
None applicable.
4 Classification
The coating is classified according to the degree of chemical resistance required.
Type A : resistant to phosphate ester hydraulic fluid;
Type B : for military use.
5 Batch release and qualification testing
5.1 Batch release testing
For batch acceptance the tests marked with an * shall be performed.
5.2 Qualification tests
For product qualification, all tests mentioned in this standard, in the Tables 1 to 5, shall be performed.
NOTE If the product is formulated by the addition
...