Roofing and cladding products from metal sheet - Specification for fully supported products of aluminium sheet

This European Standard specifies requirements for roofing and cladding products used for assembly into coverings for wall claddings, linings and pitched roofs, made from aluminium sheet with or without additional surface treatment (organic coating or anodising).
The standard establishes general characteristics, definitions and labelling of the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. Products can be prefabricated or semi-formed products as well as strip, coil and sheet for on-site-formed applications (e.g. standing seam roofs).
The standard applies to all discontinuously laid and fully supported roofing and cladding products made of aluminium sheets. No requirements for supporting construction, design of roof system and execution of connections and flashings are included.
The standard does not apply to self-supporting aluminium sheets that are covered by EN 508-2.

Dachdeckungs- und Wandbekleidungselemente aus Metallblech - Festlegungen für vollflächig unterstützte Bedachungselemente aus Aluminiumblech

Die vorliegende Europäische Norm legt die Anforderungen an Dachdeckungs  und Wandbekleidungsprodukte fest, die für die Herstellung der Eindeckungen von Außen  und Innenwand-bekleidungen sowie geneigten Dächern verwendet werden, und aus Aluminiumblech mit oder ohne zusätzliche Oberflächenbehandlung (organische Beschichtungen oder Anodisierung) bestehen.
Die vorliegende Norm legt allgemeine Merkmale, Definitionen und Beschriftung für die Produkte fest, sowie die Anforderungen an die Werkstoffe, aus denen die Produkte hergestellt werden können. Sie ist dafür bestimmt, von Herstellern verwendet zu werden, um sicherzustellen, dass ihre Produkte den Anforderungen entsprechen, oder vom Käufer, um zu überprüfen, ob die Produkte in Einklang mit den Anforderungen stehen, bevor sie das Werk verlassen. Diese Norm legt die Anforderungen fest, unten denen die Produkte allen normalen Einsatzbedingungen gerecht werden. Bei den Dachdeckungsprodukten kann es sich um vorgefertigte oder halbfertige Produkte sowie um Blechstreifen, Band und Bleche für die Verarbeitung auf der Baustelle (z. B. Stehfalzdächer) handeln.
Die Norm gilt für alle überlappenden, vollflächig unterstützten Dachdeckungs- und Wandbekleidungsprodukte aus Aluminiumblech. Anforderungen an die Unterkonstruktion, die Konstruktion des Dachsystems, die Ausführung der Verbindungen und der Zubehörteile sind nicht Teil dieser Norm.
Diese Norm gilt nicht für selbsttragende Aluminiumbleche, die von EN 508-2 abgedeckt werden.

Produits de couverture et bardage en tôle métallique - Spécification pour les produits de couverture en tôle d'aluminium totalement supportés

La présente Norme Européenne spécifie les prescriptions relatives aux produits de couverture et de bardage destinés à être assemblés pour constituer des couvertures et des bardages des parements intérieurs, des toits en pente, fabriqués à partir de tôles d'aluminium, avec ou sans traitement de surface supplémentaire (revêtement organique ou anodisation).
La Norme donne les caractéristiques générales, les définitions et l'étiquetage applicables aux produits, de même que les prescriptions relatives aux matériaux à partir desquels les produits peuvent être fabriqués. Elle est destinée à être utilisée soit par les producteurs en vue de démontrer que leurs produits sont conformes aux prescriptions, soit par les acheteurs pour vérifier que les produits sont conformes avant leur expédition de l'usine. Elle spécifie les prescriptions relatives aux produits pour leur permettre de répondre à toutes les conditions normales en service. Les produits peuvent être des produits préfabriqués ou des demi-produits partiellement formés ainsi que des bandes, des bobines ou des tôles pour des applications de façonnage sur chantier (couvertures à joints debout par exemple).
La Norme s'applique à tous les produits de couverture et de bardage posés en discontinu et totalement supportés réalisés à partir de tôles en aluminium. Elle ne comporte aucune prescription relative au support de couverture, à la conception de la toiture et à la réalisation des assemblages et finitions.
La Norme ne traite pas des tôles d’aluminium autoportantes, qui sont couvertes par l’EN 508-2.

Pločevina za pokrivanje streh in oblaganje sten - Specifikacija za povsem podprte proizvode iz aluminijske pločevine

Ta evropski standard določa zahteve za izdelke za pokrivanje streh in oblaganje sten, ki se uporabljajo v prevlekah za zunanje in notranje stenske obloge ter poševne strehe, izdelane iz aluminijeve pločevine z dodatno površinsko obdelavo ali brez nje (organska prevleka ali anodiziranje).
Ta standard določa splošne lastnosti, definicije in označevanje izdelkov ter zahteve za materiale, iz katerih so izdelki lahko proizvedeni. Namenjen je proizvajalcem, da se zagotovi skladnost njihovih izdelkov z zahtevami, oziroma kupcem, da lahko preverijo skladnost izdelkov pred razpošiljanjem iz tovarne. Določa zahteve za izdelke, ki omogočajo, da slednji izpolnjujejo vse običajne pogoje uporabe. Izdelki so lahko predizdelani ali poloblikovani izdelki ter tudi trakovi, zvitki in plošče za namestitev na mestu uporabe (npr. kritine s stoječim zgibom).
Standard se uporablja za vse nezvezno položene in povsem podprte izdelke za pokrivanje streh in oblaganje sten, izdelane iz aluminijeve pločevine. Standard ne vključuje zahtev za podporne konstrukcije, projektiranje strešnega sistema ter postavitev povezav in obrob.
Ta standard se ne uporablja za samonosilne aluminijeve pločevine, zajete v standardu EN 508-2.

General Information

Status
Published
Public Enquiry End Date
19-Oct-2017
Publication Date
03-Sep-2019
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
28-Aug-2019
Due Date
02-Nov-2019
Completion Date
04-Sep-2019

Relations

Buy Standard

Standard
EN 507:2019
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 507:2017
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 507:2019
01-oktober-2019
Nadomešča:
SIST EN 507:2000
Pločevina za pokrivanje streh in oblaganje sten - Specifikacija za povsem podprte
proizvode iz aluminijske pločevine
Roofing and cladding products from metal sheet - Specification for fully supported
products of aluminium sheet
Dachdeckungs- und Wandbekleidungselemente aus Metallblech - Festlegungen für
vollflächig unterstützte Bedachungselemente aus Aluminiumblech
Produits de couverture et bardage en tôle métallique - Spécification pour les produits de
couverture en tôle d'aluminium totalement supportés
Ta slovenski standard je istoveten z: EN 507:2019
ICS:
77.150.10 Aluminijski izdelki Aluminium products
91.060.20 Strehe Roofs
SIST EN 507:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 507:2019

---------------------- Page: 2 ----------------------
SIST EN 507:2019


EN 507
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2019
EUROPÄISCHE NORM
ICS 77.150.10; 91.060.20 Supersedes EN 507:1999
English Version

Roofing and cladding products from metal sheet -
Specification for fully supported products of aluminium
sheet
Produits de couverture et bardage en tôle métallique - Dachdeckungs- und Wandbekleidungselemente aus
Spécification pour les produits de couverture en tôle Metallblech - Festlegungen für vollflächig unterstützte
d'aluminium totalement supportés Bedachungselemente aus Aluminiumblech
This European Standard was approved by CEN on 26 May 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 507:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 507:2019
EN 507:2019 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, symbols and abbreviations . 6
3.1 Terms and definitions . 6
3.2 Symbols and abbreviations . 7
4 Requirements . 8
4.1 General . 8
4.2 Materials . 8
4.2.1 Aluminium . 8
4.2.2 Organic coatings . 9
4.2.3 Anodizing . 10
4.3 Products . 10
4.3.1 Flat products . 10
4.3.2 Formed (prefabricated) products . 10
4.3.3 Safety in case of fire . 10
5 Sampling and test methods . 10
5.1 Flat products . 10
5.2 Formed (prefabricated) products . 11
5.2.1 Sampling . 11
5.2.2 Testing . 11
6 Designation. 11
7 Marking, labelling, packaging, special ordering conditions, transport, storage and
handling . 11
7.1 Marking and labelling . 11
7.2 Packaging and any special ordering conditions . 12
7.3 Transport, storage and handling . 12
Bibliography . 13

2

---------------------- Page: 4 ----------------------
SIST EN 507:2019
EN 507:2019 (E)
European foreword
This document (EN 507:2019) has been prepared by Technical Committee CEN/TC 128 “Roof covering
products for discontinuous laying and products for wall cladding”, the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest byFebruary 2020, and conflicting national standards shall
be withdrawn at the latest by February 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 507:1999.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
In comparison to the previous edition following technical changes were made:
— scope of the standard has been extended to cladding products;
— reference has been added to anodised aluminium sheets;
— list aluminium alloys suitable without further proof provided their properties conform to the values
given in the respective material standards (EN 485 or EN 1396) as well as concerning organic
coatings suitable for application to aluminium substrates within the scope of this standard have been
changed;
— Annex A concerning the national A-deviations was deleted.
These changes or additions can be found in the following Clauses and subclauses: 1; 2; 3.1.2; 3.1.3; 3.1.5;
3.1.6; 3.1.7; 3.2; 4.1; 4.2.1; 4.2.2; 4.2.3; 4.3.3; 5.1; 5.2.1; 5.2.2.2 and 7.3.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.

3

---------------------- Page: 5 ----------------------
SIST EN 507:2019
EN 507:2019 (E)
Introduction
Figure 1 indicates the position of this standard in the CEN framework of standards concerning roofing
and cladding products of metal sheet.

Figure 1 — Framework of standards
In this standard the performance of the product has been defined in terms of a number of type tests.
The performance of a roof or cladding constructed with these products depends not only on the
properties of the product as it is required by this document, but also on the design, construction and
performance of the roof or the cladding as a whole in relation to the environment and conditions of use.
4

---------------------- Page: 6 ----------------------
SIST EN 507:2019
EN 507:2019 (E)
Metallic coated aluminium sheet can be easily fabricated. It can be sheared, punched, pressed, drawn,
folded, roll-formed without difficulty within the given limits of the properties listed in the respective
material specifications.
Coil coated sheet can be fabricated like metallic coated aluminium sheet in most applications, but
minimum bend radius, design of forming tools, process temperature, etc. are chosen according to material
properties.
5

---------------------- Page: 7 ----------------------
SIST EN 507:2019
EN 507:2019 (E)
1 Scope
This document specifies requirements for roofing and cladding products used for assembly into coverings
for wall claddings, linings and pitched roofs, made from aluminium sheet with or without additional
surface treatment (organic coating or anodising).
This document establishes general characteristics, definitions and labelling of the products, together with
requirements for the materials from which the products can be manufactured. It is intended to be used
either by manufacturers to ensure that their products comply with the requirements or by purchasers to
verify that the products comply before they are despatched from the factory. It specifies the requirements
for products which enable them to meet all normal service conditions. Products can be prefabricated or
semi-formed products as well as strip, coil and sheet for on-site-formed applications (e.g. standing seam
roofs).
This document applies to all discontinuously laid and fully supported roofing and cladding products made
of aluminium sheets. No requirements for supporting construction, design of roof system and execution
of connections and flashings are included.
This document does not appl
...

SLOVENSKI STANDARD
oSIST prEN 507:2017
01-oktober-2017
3ORþHYLQD]DSUHNULYDQMHVWUHKLQREODJDQMHVWHQ6SHFLILNDFLMH]DSRYVHPSRGSUWH
SURL]YRGHL]DOXPLQLMVNHSORþHYLQH
Roofing and cladding products from metal sheet - Specification for fully supported
products of aluminium sheet
Dachdeckungs- und Wandbekleidungselemente aus Metallblech - Festlegungen für
vollflächig unterstützte Bedachungselemente aus Aluminiumblech
Produits de couverture et bardages en tôle métallique - Spécification pour les produits de
couverture en tôle d'aluminium totalement supportés
Ta slovenski standard je istoveten z: prEN 507
ICS:
77.150.10 Aluminijski izdelki Aluminium products
91.060.20 Strehe Roofs
oSIST prEN 507:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 507:2017

---------------------- Page: 2 ----------------------
oSIST prEN 507:2017


DRAFT
EUROPEAN STANDARD
prEN 507
NORME EUROPÉENNE

EUROPÄISCHE NORM

August 2017
ICS 77.150.10; 91.060.20 Will supersede EN 507:1999
English Version

Roofing and cladding products from metal sheet -
Specification for fully supported products of aluminium
sheet
Produits de couverture et bardages en tôle métallique - Dachdeckungs- und Wandbekleidungselemente aus
Spécification pour les produits de couverture en feuille Metallblech - Festlegungen für vollflächig unterstützte
d'aluminium totalement supportés Bedachungselemente aus Aluminiumblech
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 128.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 507:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 507:2017
prEN 507:2017 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions, symbols and abbreviations . 5
3.1 Terms and definitions. 5
3.2 Symbols and abbreviations . 6
4 Requirements. 7
4.1 General . 7
4.2 Materials . 7
4.3 Products . 9
5 Sampling and test methods . 9
5.1 Flat products . 9
5.2 Formed (prefabricated) products . 10
6 Designation . 10
7 Marking, labelling and packaging . 11
7.1 Marking and labelling . 11
7.2 Packaging and any special ordering conditions . 11
7.3 Transport, storage and handling . 11
Bibliography . 12

2

---------------------- Page: 4 ----------------------
oSIST prEN 507:2017
prEN 507:2017 (E)
European foreword
This document (prEN 507:2017) has been prepared by CEN/TC 128 “Roof covering products for
discontinuous laying and products for wall cladding”, the secretariat of which is held by NBN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 507:1999.
In comparison with EN 507:1999, the following clauses have been changed or added: 1; 2; 3.1.2; 3.1.3; 3.1.5;
3.1.6; 3.1.7; 3.2; 4.1; 4.2.1; 4.2.2; 4.2.3; 4.3.3; 5.1; 5.2.1; 5.2.2.2 and 7.3. Annex A concerning the national A-
deviations has been deleted.
3

---------------------- Page: 5 ----------------------
oSIST prEN 507:2017
prEN 507:2017 (E)
Introduction
Figure 1 indicates the position of this standard in the CEN framework of standards concerning roofing
product of metal.

  Roofing and cladding products of
metal


 Self supporting  Fully supported products
products
EN 14782
EN 14783


Zinc  Stainless steel Copper Steel Aluminium
EN 501 EN 502 EN 504 EN 505 prEN 507

    References regarding


     Materials

     Quality
assurance
Figure 1 — Framework of standards
In this standard the performance of the product has been defined in terms of a number of type tests.
The performance of a roof constructed with these products depends not only on the properties of the
product as it is required by this standard, but also on the design, construction and performance of the roof as
a whole in relation to the environment and conditions of use.
Metallic coated aluminium sheet can be easily fabricated. It can be sheared, punched, pressed, drawn, folded,
roll-formed without difficulty within the given limits of the properties listed in the respective material
specifications.
Coil coated sheet can be fabricated like metallic coated aluminium sheet in most applications, but minimum
bend radius, design of forming tools, process temperature etc are chosen according to material properties.
4

---------------------- Page: 6 ----------------------
oSIST prEN 507:2017
prEN 507:2017 (E)
1 Scope
This European Standard specifies requirements for roofing and cladding products used for assembly into
coverings for wall claddings, linings and pitched roofs, made from aluminium sheet with or without
additional surface treatment (organic coating or anodising).
The standard establishes general characteristics, definitions and labelling of the products, together with
requirements for the materials from which the products can be manufactured. It is intended to be used
either by manufacturers to ensure that their products comply with the requirements or by purchasers to
verify that the products comply before they are despatched from the factory. It specifies the requirements
for products which enable them to meet all normal service conditions. Products can be prefabricated or
semi-formed products as well as strip, coil and sheet for on-site-formed applications (e.g. standing seam
roofs).
The standard applies to all discontinuously laid and fully supported roofing and cladding products made of
aluminium sheets. No requirements for supporting construction, design of roof system and execution of
connections and flashings are included.
The standard does not apply to self-supporting aluminium sheets that are covered by EN 508-2.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 485-1, Aluminium and aluminium alloys — Sheet, strip and plate — Part 1: Technical conditions for
inspection and delivery
EN 485-2, Aluminium and aluminium alloys — Sheet, strip and plate — Part 2: Mechanical properties
EN 485-4, Aluminium and aluminium alloys — Sheet, strip and plate — Part 4: Tolerances on shape and
dimensions for cold-rolled products
EN 508-2, Roofing products from metal sheet — Specification for self-supporting products of steel, aluminium
or stainless steel sheet — Part 2: Aluminium
EN 1396, Aluminium and aluminium alloys — Coil coated sheet and strip for general applications —
Specifications
EN 10204, Metallic products — Types of inspection documents
EN ISO 7599, Anodizing of aluminium and its alloys — General specifications for anodic oxidation coatings on
aluminium (ISO 7599)
3 Term
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.