SIST EN ISO 14323:2015

SLOVENSKI STANDARD
SIST EN ISO 14323:2015
01-maj-2015
1DGRPHãþD
SIST EN ISO 14323:2006
7RþNRYQRLQEUDGDYLþQRXSRURYQRYDUMHQMH±3RUXãLWYHQHSUHLVNDYH]YDURY0HUH
Y]RUFHYLQSRVWRSHN]DXGDUQLVWULåQLLQSUHþQLQDWH]QLSUHVNXV,62
Resistance spot welding and projection welds - Destructive testing of welds - Specimen
dimensions and procedure for impact shear test and cross-tension testing (ISO
14323:2015)
Widerstandspunkt- und Buckelschweißen - Zerstörende Prüfung von
Schweißverbindungen - Probenabmessungen und Durchführung des
Schlagscherzugversuchs und des Schlagkopfzugversuchs (ISO 14323:2015)
Soudage par résistance par points et par bossages - Essais destructifs des soudures -
Dimensions des éprouvettes et procédure d'essai de cisaillement par choc et d'essai de
traction par choc sur éprouvettes en croix (ISO 14323:2015)
Ta slovenski standard je istoveten z: EN ISO 14323:2015
ICS:
25.160.40 Varjeni spoji in vari Welded joints
SIST EN ISO 14323:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 14323:2015

---------------------- Page: 2 ----------------------

SIST EN ISO 14323:2015

EUROPEAN STANDARD
EN ISO 14323

NORME EUROPÉENNE

EUROPÄISCHE NORM
March 2015
ICS 25.160.40 Supersedes EN ISO 14323:2006
English Version
Resistance welding - Destructive testing of welds - Specimen
dimensions and procedure for impact tensile shear test and
cross-tension testing of resistance spot and embossed projection
welds (ISO 14323:2015)
Soudage par résistance - Essais destructifs des soudures - Widerstandsschweißen - Zerstörende Prüfung von
Dimensions des éprouvettes et mode opératoire pour les Schweißverbindungen - Probenabmessungen und
essais de cisaillement par choc et les essais de traction par Durchführung des Schlagscherzugversuchs und des
choc sur éprouvettes en croix des soudures par résistance Schlagkopfzugversuchs von Widerstandspunkt- und
par points et par bossage (ISO 14323:2015) Buckelschweißungen mit geprägten Buckeln (ISO
14323:2015)
This European Standard was approved by CEN on 29 November 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14323:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 14323:2015
EN ISO 14323:2015 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 14323:2015
EN ISO 14323:2015 (E)
Foreword
This document (EN ISO 14323:2015) has been prepared by IIW “International Institute of Welding” in
collaboration with Technical Committee CEN/TC 121 “Welding and allied processes” the secretariat of which
is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2015, and conflicting national standards shall be
withdrawn at the latest by September 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14323:2006.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 14323:2015 has been approved by CEN as EN ISO 14323:2015 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 14323:2015

---------------------- Page: 6 ----------------------

SIST EN ISO 14323:2015
INTERNATIONAL ISO
STANDARD 14323
Second edition
2015-03-01
Resistance welding — Destructive
testing of welds — Specimen
dimensions and procedure for
impact tensile shear test and cross-
tension testing of resistance spot and
embossed projection welds
Soudage par résistance — Essais destructifs des soudures —
Dimensions des éprouvettes et mode opératoire pour les essais de
cisaillement par choc et les essais de traction par choc sur éprouvettes
en croix des soudures par résistance par points et par bossage
Reference number
ISO 14323:2015(E)
©
ISO 2015

---------------------- Page: 7 ----------------------

SIST EN ISO 14323:2015
ISO 14323:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 14323:2015
ISO 14323:2015(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test specimen . 1
5 Test equipment and testing procedure . 2
5.1 General . 2
5.2 Modified pendulum machine . 3
5.3 Drop-weight machine . 5
6 Test records.10
7 Test report .10
Annex A (informative) Determination of failure energy .12
Bibliography .15
© ISO 2015 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 14323:2015
ISO 14323:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/IIW, International Institute of Welding, Commission
III.
This second edition cancels and replaces the first edition (ISO 14323:2006), which has been technically
revised.
Requests for official interpretations of any aspect of this International Standard should be directed to
the ISO Central Secretariat, who will forward them to the IIW Secretariat for an official response.
iv © ISO 2015 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 14323:2015
ISO 14323:2015(E)

Introduction
This edition of ISO 14323 no longer includes figures showing failure types and modes for tensile shear
and cross tension testing in accordance with ISO 14329:2003.
ISO 14323 was revised to align it with ISO 17677-1.
© ISO 2015 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 14323:2015

---------------------- Page: 12 ----------------------

SIST EN ISO 14323:2015
INTERNATIONAL STANDARD ISO 14323:2015(E)
Resistance welding — Destructive testing of welds —
Specimen dimensions and procedure for impact tensile
shear test and cross-tension testing of resistance spot and
embossed projection welds
1 Scope
This International Standard specifies specimen dimensions and testing procedures for impact tensile
shear and cross-tension testing of resistance spot and embossed projection welds in overlapping sheets,
in any metallic material of thickne
...