SIST EN ISO 179-2:2020

Oznaka standarda: SIST EN ISO 179-2:2020
Koda projekta: 00249A0R
Organizacija: SIST
Naslov (angleški): Plastics - Determination of Charpy impact properties - Part 2: Instrumented impact test (ISO 179-2:2020)
Naslov (slovenski): Polimerni materiali - Določanje udarne žilavosti po Charpyju - 2. del: Preskus udarne žilavosti z instrumentalnim prikazom (ISO 179-2:2020)
Če kupite standardizacijski dokument v .pdf formatu prek spletne prodaje, vam nudimo 10% popust pri spodnji ceni brez DDV. Cenik SIST
Dokumenti
Ime Jezik Status Cena Dodaj v košarico
SIST EN ISO 179-2:2020 angleški jezik Active SIST-G: 72.60 EUR
PDF
Papir
Tehnični odbor: IPMA - Polimerni materiali in izdelki
ICS: 83.080.01
Status: Objavljen
Objavljen: 01-sep-2020
Refer. št. objave: Sporocila 2020-09
Referenčna oznaka: EN ISO 179-2:2020
Področje projekta (angleško): 1.1 This document specifies a method for determining Charpy impact properties of plastics from force-deflection diagrams. Different types of rod-shaped test specimens and test configurations, as well as test parameters depending on the type of material, the type of test specimen and the type of notch, are defined in ISO 179-1. Dynamic effects such as load-cell/striker resonance, test specimen resonance and initial-contact/ inertia peaks are described in this document (see Figure 1, Curve b, and Annex A). 1.2 ISO 179-1 is suitable for characterizing the impact behaviour by the impact strength only and for using apparatus whose potential energy is matched approximately to the particular energy to break to be measured (see ISO 13802:2015, Annex E). This document is used to record a force-deflection or force-time diagram for detailed characterization of the impact behaviour, and for developing automatic apparatus, i.e. avoiding the need to match energy. The method described in this document is also suitable for: — acquiring more and different materials characteristics under impact conditions; — supervising the Charpy test procedure, as this instrumentation allows detection of typical operational mistakes, such as the specimen not being in close contact with the supports; — automatically detecting the type of break; — pendulum type instruments to avoid frequent changes of pendulum hammers; — measuring fracture mechanical properties described in other ISO standards. 1.3 For the range of materials which can be tested by this method, see ISO 179-1:2010, Clause 1. 1.4 For the general comparability of test results, see ISO 179-1:2010, Clause 1. 1.5 Information on the typical behaviour of materials can be obtained by testing at different temperatures, by varying the notch radius and/or specimen thickness and by testing specimens prepared under different conditions. It is not the purpose of this document to give an interpretation of the mechanism occurring at every point on the force-deflection diagram. These interpretations are a task for on-going scientific research. 1.6 The test results obtained with this method are comparable only if the conditions of test specimen preparation, as well as the test conditions, are the same. The impact behaviour of finished products cannot, therefore, be predicted directly from this test.
Povezava na standarde
Povezava Ime Datum
Revidiran SIST EN ISO 179-2:2000/A1:2014 - Polimerni materiali - Določanje udarne žilavosti po Charpyju - 2. del: Preskus udarne žilavosti z instrumentalnim prikazom - Dopolnilo 1: Podatki za natančnost (ISO 179-2:1997/Amd 1:2011) 23-maj-2018
Nadomešča SIST EN ISO 179-2:2000/A1:2014 - Polimerni materiali - Določanje udarne žilavosti po Charpyju - 2. del: Preskus udarne žilavosti z instrumentalnim prikazom - Dopolnilo 1: Podatki za natančnost (ISO 179-2:1997/Amd 1:2011) 10-jun-2020
Revidiran SIST EN ISO 179-2:2000 - Polimerni materiali - Določanje udarne žilavosti po Charpyju - 2. del: Preskus udarne žilavosti z instrumentalnim prikazom (ISO 179-2:1997) 23-maj-2018
Nadomešča SIST EN ISO 179-2:2000 - Polimerni materiali - Določanje udarne žilavosti po Charpyju - 2. del: Preskus udarne žilavosti z instrumentalnim prikazom (ISO 179-2:1997) 10-jun-2020


• Slovenski standardi SIST s cenovnim razredom AC so popravki standardov in so v večini primerov brezplačni.

• Slovenski standardi SIST s cenovnim razredom AP so privzeti tuji standardi, katerih sestavni del je izvirni standard, ki ga moramo pridobiti pri izdajatelju v tujini. Naročilo pošljite na: prodaja@sist.si.

Najbolje prodajani standardi