Coil coated metals - Test methods - Part 9: Resistance to water immersion

EN 13523-9 specifies the procedure for determining the resistance to water immersion of an organic coating on a metallic substrate. The test is applicable to all kinds of organic coatings, including metallics and embossed, textured, pearlescent and printed coatings. The results of the test give an indication of the resistance of the coil coated metal to water. The method is not intended to reproduce any particular condition of condensation.

Bandbeschichtete Metalle - Prüfverfahren - Teil 9: Beständigkeit gegen Eintauchen in Wasser

Dieser Teil von EN 13523 legt das Verfahren zum Bestimmen der Beständigkeit einer organischen Beschichtung auf einem metallischen Substrat gegen Eintauchen in Wasser fest.
Die Prüfung ist auf alle Arten von organischen Beschichtungen anwendbar, einschließlich Metallic- und Struktur-Beschichtungen, geprägte und bedruckte Beschichtungen, Beschichtungen mit Perlglanzeffekt. Die Ergebnisse der Prüfung geben einen Hinweis auf die Beständigkeit des bandbeschichteten Metalls gegen Wasser.
Das Verfahren ist nicht dazu gedacht, besondere Kondensationsbedingungen nachzustellen.

Tôles prélaquées - Méthodes d'essai - Partie 9: Résistance à l'immersion dans l'eau

La présente partie de l’EN 13523 décrit le mode opératoire permettant de déterminer la résistance à l'immersion dans l'eau d’un revêtement organique appliqué sur un subjectile métallique.
Cet essai s'applique à tous les types de revêtements organiques, y compris les revêtements métallisés, emboutis, texturés, nacrés et imprimés. Les résultats de l'essai permettent d'évaluer la résistance de la tôle prélaquée à l'eau.
Cette méthode ne vise pas à reproduire une quelconque condition de condensation.

Prevlečene kovine, ki se navijajo - Preskusne metode - 9. del: Odpornost proti potapljanju v vodi

Standard EN 13523-9 določa postopek za določanje odpornosti organske prevleke na kovinski podlagi proti potapljanju v vodi . Preskus se uporablja za vse vrste organskih prevlek, vključno s kovinskimi in reliefnimi, teksturnimi, bisernimi in tiskanimi prevlekami. Rezultati preskusa podajo oceno odpornosti prevlečene kovine, ki se navija, proti potapljanju v vodi. Metoda ni namenjena poustvarjanju nobenih pogojev kondenzacije.

General Information

Status
Withdrawn
Public Enquiry End Date
31-Mar-2014
Publication Date
07-Jul-2014
Withdrawal Date
15-Aug-2022
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Aug-2022
Due Date
24-Aug-2022
Completion Date
16-Aug-2022

Relations

Buy Standard

Standard
EN 13523-9:2014
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
k FprEN 13523-9:2014
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bandbeschichtete Metalle - Prüfverfahren - Teil 9: Beständigkeit gegen Eintauchen in WasserTôles prélaquées - Méthodes d'essai - Partie 9: Résistance à l'immersion dans l'eauCoil coated metals - Test methods - Part 9: Resistance to water immersion25.220.60Organske prevlekeOrganic coatings17.040.20Lastnosti površinProperties of surfacesICS:Ta slovenski standard je istoveten z:EN 13523-9:2014SIST EN 13523-9:2014en,fr,de01-september-2014SIST EN 13523-9:2014SLOVENSKI
STANDARDSIST EN 13523-9:20021DGRPHãþD



SIST EN 13523-9:2014



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13523-9
June 2014 ICS 25.220.60 Supersedes EN 13523-9:2001English Version
Coil coated metals - Test methods - Part 9: Resistance to water immersion
Tôles prélaquées - Méthodes d'essai - Partie 9: Résistance à l'immersion dans l'eau
Bandbeschichtete Metalle - Prüfverfahren - Teil 9: Beständigkeit gegen Eintauchen in Wasser This European Standard was approved by CEN on 7 May 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13523-9:2014 ESIST EN 13523-9:2014



EN 13523-9:2014 (E) 2 Contents Page Foreword .3 1 Scope .5 2 Normative references .5 3 Terms and definitions .5 4 Principle .5 5 Apparatus and materials .6 6 Sampling .6 7 Test specimens .6 8 Procedure .6 9 Expression of results .7 10 Precision .8 11 Test report .8 Annex A (normative)
Scribing of test panels .9 Bibliography . 10
SIST EN 13523-9:2014



EN 13523-9:2014 (E) 3 Foreword This document (EN 13523-9:2014) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2014, and conflicting national standards shall be withdrawn at the latest by December 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13523-9:2001. The main technical changes are: a) in 5.3 the angle 15° to 20° to the vertical was revised; b) in 5.5 the description of the cutting tool and cut was revised and aligned with EN 13523-19, i.e. 0,2 mm width; c) in 8.2 “dry them in a stream of warm air” was changed to “Immediately after removal of the test panel from the tank”; d) in 8.2.3 only one procedure for category 1 and category 2 coatings is specified for measuring corrosion creep; e) for the expression of results in Clause 9 reference to EN ISO 4628-2 for blistering and EN ISO 4628-8 for delamination around a scribe was added; f) in Figure A.1 an indication of the rolling direction was added. EN 13523, Coil coated metals — Test methods, consists of the following parts: — Part 0: General introduction — Part 1: Film thickness — Part 2: Gloss — Part 3: Colour difference — Instrumental comparison — Part 4: Pencil hardness — Part 5: Resistance to rapid deformation (impact test) — Part 6: Adhesion after indentation (cupping test) — Part 7: Resistance to cracking on bending (T-bend test) — Part 8: Resistance to salt spray (fog) — Part 9: Resistance to water immersion — Part 10: Resistance to fluorescent UV radiation and water condensation SIST EN 13523-9:2014



EN 13523-9:2014 (E) 4 — Part 11: Resistance to solvents (rubbing test) — Part 12: Resistance to scratching — Part 13: Resistance to accelerated ageing by the use of heat — Part 14: Chalking (Helmen method) — Part 15: Metamerism — Part 16: Resistance to abrasion — Part 17: Adhesion of strippable films — Part 18: Resistance to staining — Part 19: Panel design and method of atmospheric exposure testing — Part 20: Foam adhesion — Part 21: Evaluation of outdoor exposed panels — Part 22: Colour difference — Visual comparison — Part 23: Resistance to humid atmospheres containing sulfur dioxide — Part 24: Resistance to blocking and pressure marking — Part 25: Resistance to humidity — Part 26: Resistance to condensation of water — Part 27: Resistance to humid poultice (Cataplasm test) — Part 29: Resistance to environmental soiling (Dirt pick-up and striping) According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, P
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bandbeschichtete Metalle - Prüfverfahren - Teil 9: Beständigkeit gegen Eintauchen in WasserTôles prélaquées - Méthodes d'essai - Partie 9: Résistance à l'immersion dans l'eauCoil coated metals - Test methods - Part 9: Resistance to water immersion25.220.60Organske prevlekeOrganic coatings17.040.20Lastnosti površinProperties of surfacesICS:Ta slovenski standard je istoveten z:FprEN 13523-9kSIST FprEN 13523-9:2014en,fr,de01-marec-2014kSIST FprEN 13523-9:2014SLOVENSKI
STANDARD



kSIST FprEN 13523-9:2014



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN 13523-9
February 2014 ICS 25.220.60 Will supersede EN 13523-9:2001English Version
Coil coated metals - Test methods - Part 9: Resistance to water immersion
Tôles prélaquées - Méthodes d'essai - Partie 9: Résistance à l'immersion dans l'eau
Bandbeschichtete Metalle - Prüfverfahren - Teil 9: Beständigkeit gegen Eintauchen in Wasser This draft European Standard is submitted to CEN members for formal vote. It has been drawn up by the Technical Committee CEN/TC 139.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN 13523-9:2014 EkSIST FprEN 13523-9:2014



FprEN 13523-9:2014 (E) 2 Contents Page Foreword .3 1 Scope .5 2 Normative references .5 3 Terms and definitions .5 4 Principle .5 5 Apparatus and materials .5 6 Sampling .6 7 Test specimens .6 8 Procedure .6 9 Expression of results .7 10 Precision .7 11 Test report .8 Annex A (normative) Scribing of test panels .9 Bibliography . 10
kSIST FprEN 13523-9:2014



FprEN 13523-9:2014 (E) 3 Foreword This document (FprEN 13523-9:2014) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by DIN. This document is currently submitted to the Formal Vote. This document will supersede EN 13523-9:2001. The main technical changes are: a) in 5.3 the angle 15° to 20° to the vertical was revised; b) in 5.5 the description of the cutting tool and cut was revised and aligned with EN 13523-19, i.e. 0,2 mm width; c) in 8.2 “dry them in a stream of warm air” was changed to “Immediately after removal of the test panel from the tank”; d) in 8.2.3 only one procedure for category 1 and category 2 coatings is specified for measuring corrosion creep; e) for the expression of results in Clause 9 reference to EN ISO 4628-2 for blistering and EN ISO 4628-8 for delamination around a scribe was added; f) in Figure A.1 an indication of the rolling direction was added. EN 13523, Coil coated metals — Test methods, consists of the following parts: — Part 0: General introduction — Part 1: Film thickness — Part 2: Gloss — Part 3: Colour difference — Instrumental comparison — Part 4: Pencil hardness — Part 5: Resistance to rapid deformation (impact test) — Part 6: Adhesion after indentation (cupping test) — Part 7: Resistance to cracking on bending (T-bend test) — Part 8: Resistance to salt spray (fog) — Part 9: Resistance to water immersion — Part 10: Resistance to fluorescent UV radiation and water condensation — Part 11: Resistance to solvents (rubbing test) — Part 12: Resistance to scratching kSIST FprEN 13523-9:2014



FprEN 13523-9:2014 (E) 4 — Part 13: Resistance to accelerated ageing by the use of heat — Part 14: Chalking (Helmen method) — Part 15: Metamerism — Part 16: Resistance to abrasion — Part 17: Adhesion of strippable films — Part 18: Resistance to staining — Part 19: Panel design and method of atmospheric exposure testing — Part 20: Foam adhesion — Part 21: Evaluation of outdoor exposed panels — Part 22: Colour difference — Visual comparison — Part 23: Resistance to humid atmospheres containing sulfur dioxide — Part 24: Resistance to blocking and pressure marking — Part 25: Resistance to humidity — Part 26: Resistance to condensation of water — Part 27: Resistance to humid poultice (Cataplasm test) — Part 29: Resistance to environmental soiling (Dirt pick-up and striping) kSIST FprEN 13523-9:2014



FprEN 13523-9:2014 (E) 5 1 Scope This Part of EN 13523 specifies the procedure for determining the resistance to water immersion of an organic coating on a metallic subs
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.