SIST EN 60127-5:2017

SLOVENSKI STANDARD
SIST EN 60127-5:2017
01-maj-2017
1DGRPHãþD
SIST EN 60127-5:1995
Miniaturne varovalke - 5. del: Smernice za ocenjevanje kakovosti miniaturnih
taljivih varovalk (IEC 60127-5:2016)
Miniature fuses - Part 5: Guidelines for quality assessment of miniature fuse-links (IEC
60127-5:2016)
Geräteschutzsicherungen - Teil 5: Leitlinien für die Gütebestätigung von G-
Sicherungseinsätzen (IEC 60127-5:2016)
Coupe-circuit miniatures - Partie 5: Directives pour l'évaluation de la qualité des
éléments de remplacement miniatures (IEC 60127-5:2016)
Ta slovenski standard je istoveten z: EN 60127-5:2017
ICS:
29.120.50 9DURYDONHLQGUXJD Fuses and other overcurrent
PHGWRNRYQD]DãþLWD protection devices
SIST EN 60127-5:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60127-5:2017

---------------------- Page: 2 ----------------------

SIST EN 60127-5:2017


EUROPEAN STANDARD EN 60127-5

NORME EUROPÉENNE

EUROPÄISCHE NORM
February 2017
ICS 29.120.50 Supersedes EN 60127-5:1991
English Version
Miniature fuses - Part 5: Guidelines
for quality assessment of miniature fuse-links
(IEC 60127-5:2016)
Coupe-circuit miniatures - Partie 5: Lignes directrices  Geräteschutzsicherungen - Teil 5: Leitlinien
pour l'évaluation de la qualité des éléments de für die Qualitätsbewertung von G-Sicherungseinsätzen
remplacement miniatures (IEC 60127-5:2016)
(IEC 60127-5:2016)
This European Standard was approved by CENELEC on 2016-12-09. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 60127-5:2017 E

---------------------- Page: 3 ----------------------

SIST EN 60127-5:2017
EN 60127-5:2017
European foreword
The text of document 32C/526/FDIS, future edition 2 of IEC 60127-5, prepared by SC 32C "Miniature
fuses", of IEC/TC 32 "Fuses" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 60127-5:2017.
The following dates are fixed:
(dop) 2017-09-09
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2019-12-09
• latest date by which the national standards conflicting with
the document have to be withdrawn

This document supersedes EN 60127-5:1991.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60127-5:2016 was approved by CENELEC as a European
Standard without any modification.
2

---------------------- Page: 4 ----------------------

SIST EN 60127-5:2017
EN 60127-5:2017
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60127-1 2006 Miniature fuses - Part 1: Definitions for EN 60127-1 2006
miniature fuses and general
+ A1 2011 + A1 2011
requirements for miniature fuse-links
+ A2 2015 + A2 2015
IEC 60127-2 2014 Miniature fuses - Part 2: Cartridge fuse- EN 60127-2 2014
links
IEC 60127-3 2015 Miniature fuses - Part 3: Sub-miniature EN 60127-3 2015
fuse-links
IEC 60127-4 2005 Miniature fuses - Part 4: Universal EN 60127-4 2005
modular fuse-links (UMF) - Through-
+ A1 2008 + A1 2009
hole and surface mount types
+ A2 2012 + A2 2013
IEC 60127-7 2015 Miniature fuses - Part 7: Miniature fuse- EN 60127-7 2016
links for special applications

3

---------------------- Page: 5 ----------------------

SIST EN 60127-5:2017

---------------------- Page: 6 ----------------------

SIST EN 60127-5:2017



IEC 60127-5

®


Edition 2.0 2016-11




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Miniature fuses –

Part 5: Guidelines for quality assessment of miniature fuse-links




Coupe-circuit miniatures –

Partie 5: Lignes directrices pour l'évaluation de la qualité des éléments de

remplacement miniatures















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.120.50 ISBN 978-2-8322-3716-8



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60127-5:2017
– 2 – IEC 60127-5:2016 © IEC 2016
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Lot-by-lot inspection . 7
4.1 Test conditions . 7
4.2 Non-destructive tests . 7
4.3 Destructive tests . 7
4.3.1 Destructive tests for IEC 60127-2 and IEC 60127-3 . 7
4.3.2 Destructive tests for IEC 60127-4 . 8
4.3.3 Destructive tests for IEC 60127-7 . 8
4.4 Acceptance criteria . 9
5 Periodic inspection . 9
5.1 Reduced type tests for IEC 60127-2 or IEC 60127-3 . 9
5.2 Reduced type tests for IEC 60127-4 . 10
5.3 Reduced type tests for IEC 60127-7 . 10
Bibliography . 12

Table 1 – Primary characteristics (inspection level II) (Samples may be returned to the lot
after inspection) . 7
Table 2 (for IEC 60127-2 and IEC 60127-3) – Time/current characteristic
(IEC 60127-1:2006, 9.2.1) (Inspection level S4, destructive test) . 8
Table 3 (for IEC 60127-4) – Time/current characteristic (IEC 60127-1:2006, 9.2.1)
(Inspection level S4, destructive test) . 8
Table 4 (for IEC 60127-7) – Time/current characteristic (IEC 60127-1:2006, 9.2.1) –
(Inspection level S4, destructive test) . 9
Table 5 – Reduced type tests for IEC 60127-2 or IEC 60127-3 . 9
Table 6 – Reduced type tests for IEC 60127-4 . 10
Table 7 – Reduced type tests for IEC 60127-7 . 11

---------------------- Page: 8 ----------------------

SIST EN 60127-5:2017
IEC 60127-5:2016 © IEC 2016 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

MINIATURE FUSES –

Part 5: Guidelines for quality assessment of miniature fuse-links

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in
addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses
arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60127-5 has been prepared by subcommittee 32C: Miniature fuses,
of IEC technical committee 32: Fuses.
This second edition cancels and replaces the first edition published in 1988. This
...