SIST EN IEC 60384-16:2020

SLOVENSKI STANDARD
SIST EN IEC 60384-16:2020
01-januar-2020
Nadomešča:
SIST EN 60384-16:2006
Nespremenljivi kondenzatorji za uporabo v elektronski opremi - 16. del: Področna
specifikacija - Nespremenljivi kondenzatorji z dielektrikom iz metalizirane
polipropilenske folije za enosmerne napetosti (IEC 60384-16:2019)
Fixed capacitors for use in electronic equipment - Part 16: Sectional specification - Fixed
metallized polypropylene film dielectric DC capacitors (IEC 60384-16:2019)
Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 16:
Rahmenspezifikation: Festkondensatoren mit metallisierter Polypropylen-Folie als
Dielektrikum für Gleichspannung (IEC 60384-16:2019)
Condensateurs fixes utilisés dans les équipements électroniques - Partie 16:
Spécification intermédiaire - Condensateurs fixes our courant continu à diélectrique en
film de polypropylène métallisé (IEC 60384-16:2019)
Ta slovenski standard je istoveten z: EN IEC 60384-16:2019
ICS:
31.060.10 Fiksni kondenzatorji Fixed capacitors
SIST EN IEC 60384-16:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60384-16:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 60384-16:2020


EUROPEAN STANDARD EN IEC 60384-16

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2019
ICS 31.060.30 Supersedes EN 60384-16:2005 and all of its
amendments and corrigenda (if any)
English Version
Fixed capacitors for use in electronic equipment - Part 16:
Sectional specification - Fixed metallized polypropylene film
dielectric DC capacitors
(IEC 60384-16:2019)
Condensateurs fixes utilisés dans les équipements Festkondensatoren zur Verwendung in Geräten der
électroniques - Partie 16: Spécification intermédiaire - Elektronik - Teil 16: Rahmenspezifikation:
Condensateurs fixes our courant continu à diélectrique en Festkondensatoren mit metallisierter Polypropylen-Folie als
film de polypropylène métallisé Dielektrikum für Gleichspannung
(IEC 60384-16:2019) (IEC 60384-16:2019)
This European Standard was approved by CENELEC on 2019-10-21. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60384-16:2019 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60384-16:2020
EN IEC 60384-16:2019 (E)
European foreword
The text of document 40/2686/FDIS, future edition 3 of IEC 60384-16, prepared by IEC/TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 60384-16:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-07-21
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-10-21
document have to be withdrawn

This document supersedes EN 60384-16:2005 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60384-16:2019 was approved by CENELEC as a European
Standard without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60065 NOTE Harmonized as EN 60065
IEC 60068-2-20:2008 NOTE Harmonized as EN 60068-2-20:2008 (not modified)
IEC 60384-14 NOTE Harmonized as EN 60384-14
IEC 60384-17 NOTE Harmonized as EN IEC 60384-17

2

---------------------- Page: 4 ----------------------
SIST EN IEC 60384-16:2020
EN IEC 60384-16:2019 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60063 -  Preferred number series for resistors and capacitors EN 60063 -
IEC 60068-1 2013 Environmental testing - Part 1: General and EN 60068-1 2014
guidance
IEC 60384-1 2016 Fixed capacitors for use in electronic equipment - EN 60384-1 2016
Part 1: Generic specification
IEC 61193-2 2007 Quality assessment systems - Part 2: Selection and EN 61193-2 2007
use of sampling plans for inspection of electronic
components and packages
IEC 60417 -  Graphical symbols for use on equipment. Index, - -
survey and compilation of the single sheets.
ISO 3 -  Preferred numbers - Series of preferred numbers - -

3

---------------------- Page: 5 ----------------------
SIST EN IEC 60384-16:2020

---------------------- Page: 6 ----------------------
SIST EN IEC 60384-16:2020



IEC 60384-16

®


Edition 3.0 2019-09




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Fixed capacitors for use in electronic equipment –

Part 16: Sectional specification – Fixed metallized polypropylene film dielectric

DC capacitors




Condensateurs fixes utilisés dans les équipements électroniques –

Partie 16: Spécification intermédiaire – Condensateurs fixes pour courant


continu à diélectrique en film de polypropylène métallisé













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 31.060.30 ISBN 978-2-8322-7334-0




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 60384-16:2020
– 2 – IEC 60384-16:2019 © IEC 2019
CONTENTS
FOREWORD . 6
1 General . 8
1.1 Scope . 8
1.2 Object . 8
1.3 Normative references . 8
1.4 Information to be given in a detail specification . 9
1.4.1 General . 9
1.4.2 Outline drawing and dimensions . 9
1.4.3 Mounting . 9
1.4.4 Ratings and characteristics . 10
1.4.5 Marking . 10
1.5 Terms and definitions . 10
1.6 Marking . 11
1.6.1 General . 11
1.6.2 Information for marking . 11
1.6.3 Marking on capacitors . 11
1.6.4 Marking on packaging . 11
2 Preferred ratings and characteristics . 12
2.1 Preferred characteristics . 12
2.2 Preferred values of ratings . 12
2.2.1 Nominal capacitance (C ) . 12
N
2.2.2 Tolerances on nominal capacitance . 12
2.2.3 Nominal capacitance with associated tolerance values . 12
2.2.4 Rated voltage (U ) . 12
R
2.2.5 Category voltage (U ). 13
C
2.2.6 Rated temperature . 13
3 Quality assessment procedures . 13
3.1 Primary stage of manufacture . 13
3.2 Structurally similar components . 13
3.3 Certified records of released lots . 13
3.4 Qualification approval procedures . 13
3.4.1 General . 13
3.4.2 Qualification approval on the basis of the fixed sample size procedures . 13
3.5 Quality conformance inspection . 20
3.5.1 Formation of inspection lots . 20
3.5.2 Test schedule . 21
3.5.3 Delayed delivery . 21
3.5.4 Assessment levels . 21
4 Test and measurement procedures . 22
4.1 Visual examination and check of dimensions . 22
4.1.1 General . 22
4.1.2 Test conditions . 22
4.1.3 Requirements . 22
4.2 Electrical tests . 22
4.2.1 Voltage proof . 22
4.2.2 Capacitance . 23
4.2.3 Tangent of loss angle (tan δ) . 23

---------------------- Page: 8 ----------------------
SIST EN IEC 60384-16:2020
IEC 60384-16:2019 © IEC 2019 – 3 –
4.2.4 Insulation resistance . 24
4.2.5 Inductance (if required) . 26
4.2.6 Characteristics depending on temperature (if required) . 26
4.3 Robustness of terminations . 27
4.3.1 General . 27
4.3.2 Initial inspections . 27
4.3.3 Test method . 27
4.3.4 Final inspections . 27
4.4 Resistance to soldering heat . 27
4.4.1 General . 27
4.4.2 Preconditioning . 27
4.4.3 Test conditions . 27
4.4.4 Final inspections . 27
4.5 Solderability . 27
4.5.1 General . 27
4.5.2 Preconditioning . 28
4.5.3 Test conditions . 28
4.5.4 Final inspections . 28
4.6 Rapid change of temperature . 28
4.6.1 General . 28
4.6.2 Initial inspections . 28
4.6.3 Test conditions . 28
4.6.4 Recovery (if required) . 28
4.6.5 Final inspections . 28
4.7 Vibration . 28
4.7.1 General . 28
4.7.2 Mounting . 28
4.7.3 Test conditions . 28
4.7.4 Final inspections . 29
4.8 Bump (if required) . 29
4.8.1 General . 29
4.8.2 Mounting . 29
4.8.3 Initial inspections . 29
4.8.4 Test conditions . 29
4.8.5 Final inspections . 29
4.9 Shock (if required) . 29
4.9.1 General . 29
4.9.2 Mounting . 29
4.9.3 Initial inspections . 30
4.9.4 Test conditions . 30
4.9.5 Final inspections . 30
4.10 Climatic sequence. 30
4.10.1 General . 30
4.10.2 Initial inspections . 30
4.10.3 Dry heat . 30
4.10.4 Damp heat, cyclic, Test Db, first cycle . 30
4.10.5 Cold. 30
4.10.6 Low air pressure (if required) . 30
4.10.7 Damp heat, cyclic, Test Db, remaining cycles . 31

---------------------- Page: 9 ----------------------
SIST EN IEC 60384-16:2020
– 4 – IEC 60384-16:2019 © IEC 2019
4.11 Damp heat, steady state . 31
4.11.1 General . 31
4.11.2 Initial inspections . 31
4.11.3 Test conditions . 31
4.11.4 Recovery (if required) . 31
4.11.5 Final inspections . 32
4.11.6 Humidity robustness grades . 32
4.12 Endurance . 32
4.12.1 General . 32
4.12.2 Initial inspections . 32
4.12.3 Test conditions . 32
4.12.4 Recovery . 32
4.12.5 Final inspections . 32
4.13 Charge and discharge . 32
4.13.1 General . 32
4.13.2 Initial inspections . 32
4.13.3 Test conditions . 33
4.13.4 Recovery (if required) . 34
4.13.5 Final inspections . 34
4.14 Component solvent resistance . 34
4.15 Solvent resistance of the marking . 34
4.16 Sealing . 34
Annex A (normative) Humidity robustness grades for applications, where high stability
under high humidity operating conditions is required. 35
A.1 Scope . 35
A.2 Humidity robustness grades . 35
A.2.1 Standard . 35
A.2.2 Grade (I) robustness under humidity . 35
A.2.3 Grade (II) robustness under high humidity . 35
A.2.4 Grade (III) high robustness under high humidity . 35
A.3 Indication of humidity robustness grades . 36
Bibliography . 37

Table 1 – Preferred values . 11
Table 2 – Preferred combinations of capacitance value series and tolerances . 12
Table 3 – Sampling plan for qualification approval tests, assessment level EZ . 15
Table 4 – Test schedule for qualification approval . 16
Table 5 – Lot-by-lot inspection . 21
Table 6 – Periodic inspection . 22
Table 7 – Combinations of test point and test voltage . 23
Table 8 – Tangent of loss angle limits, 1 kHz . 24
Table 9 – Tangent of loss angle limits, 10 kHz . 24
Table 10 – Insulation resistance requirements . 25

---------------------- Page: 10 ----------------------
SIST EN IEC 60384-16:2020
IEC 60384-16:2019 © IEC 2019 – 5 –
Table 11 – Temperature coefficient factors . 25
Table 12 – Characteristics at lower category temperature . 26
Table 13 – Characteristics at upper category temperature . 27
Table 14 – Preferred severities . 30
Table 15 – Test conditions . 32
Table 16 – Lead spacing . 33

---------------------- Page: 11 ----------------------
SIST EN IEC 60384-16:2020
– 6 – IEC 60384-16:2019 © IEC 2019
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 16: Sectional specification –
Fixed metallized polypropylene film dielectric DC capacitors

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60384-16 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
This third edition cancels and replaces the second edition published in 2005. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) revision of the structure in accordance with ISO/IEC Directives, Part 2: 2016 to the extent
practicable, and harmonization between other similar kinds of documents;
b) in addition, Clause 4 and all the tables have been reviewed in order to prevent
duplications and contradictions.

---------------------- Page: 12 ----------------------
SIST EN IEC 60384-16:2020
IEC 60384-16:201
...