Plastics - Film and sheeting - Determination of tear resistance - Part 1: Trouser tear method (ISO 6383-1:2015)

This part of ISO 6383 specifies a method of determining the tear resistance of plastic film or sheet
less than 1 mm thick, in the form of standard trouser-shaped test specimens, tested under defined
conditions of pre-treatment, temperature, humidity, and speed of testing.
The method is applicable to film and sheeting of both flexible and rigid materials, provided that the
material is not so rigid that brittle fracture occurs during the test, or so deformable, in an irreversible
way, that the energy used in the deformation of the specimen legs is significant (i.e. is not negligible)
with respect to the energy used in tearing.
The method may not be suitable for determining the tear properties of cellular sheet and film.

Kunststoffe - Folien und Bahnen - Bestimmung der Reißfestigkeit - Teil 1: Hosenreiß-Verfahren (ISO 6383-1:2015)

Dieser Teil der Internationalen Norm ISO 6383 legt ein Verfahren zur Bestimmung der Reißfestigkeit von Kunststoff-Folien oder Bahnen in Dicken kleiner 1 mm in einer Rechteckform mit Längseinschnitt als genormte Probekörper fest, die unter bestimmten Bedingungen der Vorbehandlung, der Temperatur, der relativen Feuchte und der Prüfgeschwindigkeit geprüft werden.
Das Verfahren ist sowohl auf weich-elastische als auch harte Folien und Bahnenmaterialien anwendbar, vor¬aus-gesetzt, das Material ist nicht so spröde, dass ein Bruch während der Prüfung eintritt, oder nicht so irreversibel verformbar, dass die Verformungsarbeit der Probenschenkel gegenüber der Weiterreißarbeit signifikant (d. h. nicht vernachlässigbar) wird.
Zur Bestimmung der Weiterreißeigenschaften von geschäumten Bahnen und Folien kann das Verfahren unpassend sein.

Plastiques - Film et feuille - Détermination de la résistance au déchirement - Partie 1: Méthode de déchirement pantalon (ISO 6383-1:2015)

ISO 6383-1:2015 spécifie une méthode de détermination de la résistance au déchirement des films ou des feuilles de plastique d'épaisseur inférieure à 1 mm, en utilisant des éprouvettes normalisées en forme de pantalon, soumises à l'essai dans des conditions définies de traitement préalable, de température, d'humidité et de vitesse d'essai.
La méthode est applicable à la fois aux films et aux feuilles en matériaux souples et en matériaux rigides, à condition que les matériau ne soit pas tellement rigide pour que des ruptures du type fragile aient lieu pendant l'essai, ou tellement déformable de façon irréversible que l'énergie absorbée par la déformation des jambes de l'éprouvette soit appréciable (c'est-à-dire non, négligeable) par rpport à l'énergie absorbée par le déchirement.
La méthode peut ne pas être appropriée pour la détermination des caractéristiques de déchirement des feuilles et films cellulaires.

Polimerni materiali - Filmi in folije - Ugotavljanje odpornosti proti trganju - 1. del: Metoda s trganjem hlačne epruvete (ISO 6383-1:2015)

Ta del standarda ISO 6383 določa metodo za določanje odpornosti proti trganju plastičnih filmov ali folij z debelino manj kot 1 mm v obliki standardnih preskusnih vzorcev s hlačno epruveto, preskušanih v določenih pogojih predhodne obdelave, temperature, vlažnosti in hitrosti preskušanja.
Metoda se uporablja za filme in folije iz upogljivih in togih materialov, pri čemer material ne sme biti tako tog, da pri preskusu pride do lomljenja, ali tako upogljiv, da se ne povrne v prvotno stanje in je energija, uporabljena pri upogibanju vzorčnih nog, znatna (tj. ni neznatna) glede na energijo, uporabljeno pri trganju.
Metoda morda ni primerna za določanje lastnosti trganja penjenih folij in filmov.

General Information

Status
Published
Public Enquiry End Date
09-Nov-2015
Publication Date
26-Jan-2016
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
14-Jan-2016
Due Date
20-Mar-2016
Completion Date
27-Jan-2016

Relations

Buy Standard

Standard
EN ISO 6383-1:2016
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
k FprEN ISO 6383-1:2015
German language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 6383-1:2016
01-marec-2016
1DGRPHãþD
SIST EN ISO 6383-1:2004
3ROLPHUQLPDWHULDOL)LOPLLQIROLMH8JRWDYOMDQMHRGSRUQRVWLSURWLWUJDQMXGHO
0HWRGDVWUJDQMHPKODþQHHSUXYHWH ,62
Plastics - Film and sheeting - Determination of tear resistance - Part 1: Trouser tear
method (ISO 6383-1:2015)
Kunststoffe - Folien und Bahnen - Bestimmung der Reißfestigkeit - Teil 1: Hosenreiß-
Verfahren (ISO 6383-1:2015)
Plastiques - Film et feuille - Détermination de la résistance au déchirement - Partie 1:
Méthode de déchirement pantalon (ISO 6383-1:2015)
Ta slovenski standard je istoveten z: EN ISO 6383-1:2015
ICS:
83.140.10 Filmi in folije Films and sheets
SIST EN ISO 6383-1:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 6383-1:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 6383-1:2016


EN ISO 6383-1
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2015
EUROPÄISCHE NORM
ICS 83.140.10 Supersedes EN ISO 6383-1:2004
English Version

Plastics - Film and sheeting - Determination of tear
resistance - Part 1: Trouser tear method (ISO 6383-
1:2015)
Plastiques - Film et feuille - Détermination de la Kunststoffe - Folien und Bahnen - Bestimmung der
résistance au déchirement - Partie 1: Méthode de Reißfestigkeit - Teil 1: Hosenreiß-Verfahren (ISO 6383-
déchirement pantalon (ISO 6383-1:2015) 1:2015)
This European Standard was approved by CEN on 31 October 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6383-1:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 6383-1:2016
EN ISO 6383-1:2015 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 6383-1:2016
EN ISO 6383-1:2015 (E)
European foreword
This document (EN ISO 6383-1:2015) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be
withdrawn at the latest by June 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 6383-1:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 6383-1:2015 has been approved by CEN as EN ISO 6383-1:2015 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 6383-1:2016

---------------------- Page: 6 ----------------------

SIST EN ISO 6383-1:2016
INTERNATIONAL ISO
STANDARD 6383-1
Second edition
2015-12-15
Plastics — Film and sheeting —
Determination of tear resistance —
Part 1:
Trouser tear method
Plastiques — Film et feuille — Détermination de la résistance au
déchirement —
Partie 1: Méthode de déchirement pantalon
Reference number
ISO 6383-1:2015(E)
©
ISO 2015

---------------------- Page: 7 ----------------------

SIST EN ISO 6383-1:2016
ISO 6383-1:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 6383-1:2016
ISO 6383-1:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Significance . 1
5 Principle . 2
6 Apparatus . 2
7 Test specimens. 2
8 Number of test specimens . 3
9 Speed of testing . 3
10 Conditioning . 3
11 Procedure. 3
12 Expression of results . 3
13 Test report . 4
© ISO 2015 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 6383-1:2016
ISO 6383-1:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary in
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoffe - Folien und Bahnen - Bestimmung der Reißfestigkeit - Teil 1: Hosenreiß-Verfahren (ISO/FDIS 6383-1:2015)Plastiques - Film et feuille - Détermination de la résistance au déchirement - Partie 1: Méthode de déchirement pantalon (ISO/FDIS 6383-1:2015)Plastics - Film and sheeting - Determination of tear resistance - Part 1: Trouser tear method (ISO/FDIS 6383-1:2015)83.140.10Filmi in folijeFilms and sheetsICS:Ta slovenski standard je istoveten z:FprEN ISO 6383-1kSIST FprEN ISO 6383-1:2015de01-oktober-2015kSIST FprEN ISO 6383-1:2015SLOVENSKI
STANDARD



kSIST FprEN ISO 6383-1:2015



EUROPÄISCHE NORM EUROPEAN STANDARD NORME EUROPÉENNE
SCHLUSS-ENTWURF
FprEN ISO 6383-1
Juli 2015 ICS 83.140.10 Vorgesehen als Ersatz für EN ISO 6383-1:2004Deutsche Fassung
Kunststoffe - Folien und Bahnen - Bestimmung der Reißfestigkeit - Teil 1: Hosenreiß-Verfahren (ISO/FDIS 6383-1:2015)
Plastics - Film and sheeting - Determination of tear resistance - Part 1: Trouser tear method (ISO/FDIS 6383-1:2015)
Plastiques - Film et feuille - Détermination de la résistance au déchirement - Partie 1: Méthode de déchirement pantalon (ISO/FDIS 6383-1:2015) Dieser Europäische Norm-Entwurf wird den CEN-Mitgliedern zur parallelen formellen Abstimmung vorgelegt. Er wurde vom Technischen Komitee CEN/TC 249 erstellt.
Wenn aus diesem Norm-Entwurf eine Europäische Norm wird, sind die CEN-Mitglieder gehalten, die CEN-Geschäftsordnung zu erfüllen, in der die Bedingungen festgelegt sind, unter denen dieser Europäischen Norm ohne jede Änderung der Status einer nationalen Norm zu geben ist.
Dieser Europäische Norm-Entwurf wurde vom CEN in drei offiziellen Fassungen (Deutsch, Englisch, Französisch) erstellt. Eine Fassung in einer anderen Sprache, die von einem CEN-Mitglied in eigener Verantwortung durch Übersetzung in seine Landessprache gemacht und dem Management-Zentrum des CEN-CENELEC mitgeteilt worden ist, hat den gleichen Status wie die offiziellen Fassungen.
CEN-Mitglieder sind die nationalen Normungsinstitute von Belgien, Bulgarien, Dänemark, Deutschland, der ehemaligen jugoslawischen Republik Mazedonien, Estland, Finnland, Frankreich, Griechenland, Irland, Island, Italien, Kroatien, Lettland, Litauen, Luxemburg, Malta, den Niederlanden, Norwegen, Österreich, Polen, Portugal, Rumänien, Schweden, der Schweiz, der Slowakei, Slowenien, Spanien, der Tschechischen Republik, der Türkei, Ungarn, dem Vereinigten Königreich und Zypern.
Die Empfänger dieses Norm-Entwurfs werden gebeten, mit ihren Kommentaren jegliche relevante Patentrechte, die sie kennen, mitzuteilen und unterstützende Dokumentationen zur Verfügung zu stellen.
Warnvermerk : Dieses Schriftstück hat noch nicht den Status einer Europäischen Norm. Es wird zur Prüfung und Stellungnahme vorgelegt. Es kann sich noch ohne Ankündigung ändern und darf nicht als Europäischen Norm in Bezug genommen werden.
EUROPÄISCHES KOMITEE FÜR NORMUNG EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
CEN-CENELEC Management-Zentrum:
Avenue Marnix 17,
B-1000 Brüssel © 2015 CEN Alle Rechte der Verwertung, gleich in welcher Form und in welchem Verfahren, sind weltweit den nationalen Mitgliedern von CEN vorbehalten.Ref. Nr. FprEN ISO 6383-1:2015 DkSIST FprEN ISO 6383-1:2015



FprEN ISO 6383-1:2015 (D) 2 Inhalt
Seite Vorwort .3 Einleitung .4 1 Anwendungsbereich .5 2 Normative Verweisungen .5 3 Begriffe .5 4 Bedeutung .5 5 Kurzbeschreibung .6 6 Geräte .6 7 Probekörper .6 8 Anzahl der Probekörper .6 9 Prüfgeschwindigkeit .7 10 Konditionierung .7 11 Durchführung .7 12 Auswertung der Ergebnisse .7 13 Prüfbericht .8
kSIST FprEN ISO 6383-1:2015



FprEN ISO 6383-1:2015 (D) 3 Vorwort Dieses Dokument (FprEN ISO 6383-1:2015) wurde vom Technischen Komitee ISO/TC 61 „Plastics“ in Zusammenarbeit mit dem Technischen Komitee CEN/TC 249 „Kunststoffe“ erarbeitet, dessen Sekretariat vom NBN gehalten wird. Dieses Dokument ist derzeit zur parallelen formellen Abstimmung vorgelegt. Dieses Dokument wird EN ISO 6383-1:2004 ersetzen. Anerkennungsnotiz Der Text von ISO/FDIS 6383-1:2015 wurde vom CEN als FprEN ISO 6383-1:2015 ohne irgendeine Abänderung genehmigt. kSIST FprEN ISO 6383-1:2015



FprEN ISO 6383-1:2015 (D) 4 Einleitung ISO 6383 besteht aus den folgenden Teilen:  Teil 1: Hosenreiß-Verfahren  Teil 2: Elmendorf-Verfahren
kSIST FprEN ISO 6383-1:2015



FprEN ISO 6383-1:2015 (D) 5 1 Anwendungsbereich Dieser Teil der Internationalen Norm ISO 6383 legt ein Verfahren zur Bestimmung der Reißfestigkeit von Kunststoff-Folien oder Bahnen in Dicken kleiner 1 mm in einer Rechteckform mit Längseinschnitt als genormte Probekörper fest, die unter bestimmten Bedingungen der Vorbehandlung, der Temperatur, der relativen Feuchte und der Prüfgeschwindigkeit geprüft werden. Das Verfahren ist sowohl auf weich-elastische als auch harte Folien und Bahnenmaterialien anwendbar, vor-ausgesetzt, das Material ist nicht so spröde, dass ein Bruch während der Prüfung eintritt, oder nicht so irreversibel verformbar, dass die Verformungsarbeit der Probenschenkel gegenüber der Weiterreißarbeit signifikant (d. h. nicht vernachlässigbar) wird. Zur Bestimmung der Weiterreißeigenschaften von geschäumten Bahnen und Folien kann das Verfahren unpassend sein. 2 Normative Verweisungen ISO 291, Plastics – Standard atmospheres for conditioning and testing ISO 527-3, Plastics – Determination of tensile properties – Part 3: Test conditions for films and sheets ISO 4591, Plastics – Film and sheeting – Determination of average thickness of a sample, and average thick-ness and yield of a roll by gravimetric techniques (gravimetric thickness) ISO 4593, Plastics – Film and sheeting – Determination of thickness by mechanical scanning 3 Begriffe Für die Anwendung dieses Teils von ISO 6383 gelten die folgenden Begriffe. 3.1 Weiterreißkraft mittlere erforderliche Kraft, um einen Riss bei gleich bleibender Weiterreißgeschwindigkeit durch einen mit Bild 1 übereinstimmenden Probekörper weiterzuführen 3.2 Weiterreißwiderstand Weiterreißkraft geteilt durch die Probendicke 4 Bedeutung 4.1 Das Verfahren kann Eigenschaftswerte für die Qualitätskontrolle, Annahme oder Ablehnung in Überein-stimmung mit den Vorgaben von Anforderungen und für Forschung und Entwicklung liefern. 4.2 Weiterreiß-Eigenschaftswerte können infolge unterschiedlicher Proben
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.