SIST EN 10360:2015
(Main)Hot, warm or cold forgings - Repair conditions prior to delivery
Hot, warm or cold forgings - Repair conditions prior to delivery
This European Standard defines the forged components surface repair conditions and control to preserve their functionality.
Warm-, Halbwarm- oder Kaltschmiedeteile - Nacharbeit vor Lieferung
Diese Europäische Norm legt die Reparatur- und Prüfanforderungen an Schmiedestücken fest, um die Funktionalität (zweckmäßige Bestimmung) des Schmiedeerzeugnisses zu erfüllen.
Pièces forgées à chaud, à mi-chaud ou à froid - Conditions de réparation avant livraison
La présente Norme européenne définit les conditions de maîtrise et de réparation en surface des pièces/composants forgé(e)s afin de préserver leur fonctionnalité.
Vroči, topli ali hladni izkovki - Pogoji za popravilo pred dostavo
Ta evropski standard opredeljuje pogoje za popravilo in kontrolo površin kovanih delov, da se ohrani njihova funkcionalnost.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.RWarm-, Halbwarm- oder Kaltschmiedeteile - Nacharbeit vor LieferungPièces forgées à chaud, à mi-chaud ou à froid - Conditions de réparation avant livraisonHot, warm or cold forgings - Repair conditions prior to delivery77.140.85Železni in jekleni kovani izdelkiIron and steel forgingsICS:Ta slovenski standard je istoveten z:EN 10360:2015SIST EN 10360:2015en,fr,de01-oktober-2015SIST EN 10360:2015SLOVENSKI
STANDARD
SIST EN 10360:2015
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10360
July 2015 ICS 77.140.85 English Version
Hot, warm or cold forging - Repair conditions prior to delivery
Pièces forgées à chaud, à mi-chaud ou à froid - Conditions de réparation avant livraison
Warm-, Halbwarm- oder Kaltschmiedeteile - Nacharbeit vor Lieferung This European Standard was approved by CEN on 6 June 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10360:2015 ESIST EN 10360:2015
EN 10360:2015 (E) 2 Contents Page
Foreword .3 Introduction .4 1 Scope .5 2 Terms and definitions .5 3 Prohibited repair areas .5 4 Removal of surface imperfections .5 5 Removal of surface defects .5 5.1 Surface defects removal method .5 5.2 Surface condition of the repaired area .6 5.3 Operations carried out after the surface defects removal .6 5.4 Acceptance rules for the repair process .6 6 Operator training.6 Bibliography .7
SIST EN 10360:2015
EN 10360:2015 (E) 3 Foreword This document (EN 10360:2015) has been prepared by Technical Committee ECISS/TC 111 “Steels castings and forgings”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2016 and conflicting national standards shall be withdrawn at the latest by January 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CE
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.