SIST EN 1173:2008
(Main)Copper and copper alloys - Material condition designation
Copper and copper alloys - Material condition designation
This European Standard establishes a system for designation of material conditions or tempers to be used for the identification of the mandatory property requirements. These designations are applicable to wrought products of copper and copper alloys.
Kupfer und Kupferlegierungen - Zustandsbezeichnungen
Diese Europäische Norm legt ein System zur Bezeichnung von Werkstoffzuständen fest, das zur Identifizierung von verbindlichen Anforderungen an Eigenschaften zu verwenden ist. Die Bezeichnungen gelten für plastisch geformte Produkte aus Kupfer und Kupferlegierungen.
Cuivre et alliages de cuivre - Désignation des états métallurgiques
La présente norme européenne établit un système de désignation des états métallurgiques à utiliser pour l'identification des prescriptions obligatoires concernant les caractéristiques. Ces désignations sont applicables aux produits corroyés en cuivre ou en alliages de cuivre.
Baker in bakrove zlitine - Stanje materiala in označevanje
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Copper and copper alloys - Material condition designationCuivre et alliages de cuivre - Désignation des états métallurgiquesKupfer und Kupferlegierungen - Zustandsbezeichnungen77.120.30Baker in bakrove zlitineCopper and copper alloysICS:SIST EN 1173:2008en,fr,deTa slovenski standard je istoveten z:EN 1173:200801-julij-2008SIST EN 1173:2008SLOVENSKI
STANDARDSIST EN 1173:19981DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1173April 2008ICS 77.120.30Supersedes EN 1173:1995
English VersionCopper and copper alloys - Material condition designationCuivre et alliages de cuivre - Désignation des étatsmétallurgiquesKupfer und Kupferlegierungen - ZustandsbezeichnungenThis European Standard was approved by CEN on 21 March 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1173:2008: E
EN 1173:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Basis of designation system.4 3 Structure of designation.4 3.1 General.4 3.2 Position 1.4 3.3 Positions 2 to 4.5 3.4 Positions 5 and 6.5 4 Examples.5 4.1 General.5 4.2 Elongation.5 4.3 Spring bending limit.5 4.4 As drawn.5 4.5 Grain size.5 4.6 Hardness.6 4.7 As manufactured.6 4.8 Tensile strength.6 4.9 0,2% proof strength.6 4.10 Additional treatment "Stress relieving".6 Bibliography.7
EN 1173:2008 (E) 3 Foreword This document (EN 1173:2008) has been prepared by Technical Committee CEN/TC 133 “Copper and copper alloys”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at the latest by October 2008. Attention is drawn to the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.