Building hardware - Padlocks and padlock fittings - Requirements and test methods

This European Standard applies to mechanical padlocks and padlock fittings used on buildings and general use and specifies the test methods to be used. This European Standard specifies performance and other requirements for strength, security, durability, performance, and corrosion resistance of padlocks. It establishes one category of use, two categories of durability, six categories for corrosion resistance and six grades for security based on performance tests that simulate attack. Limited manual attack testing is included in this European Standard because the machine testing does not replicate all known manual attacks.

Baubeschläge - Hangschlösser und Hangschlossbeschläge - Anforderungen und Prüfverfahren

Dieses Dokument gilt für mechanische Hangschlösser und Hangschlossbeschläge zur üblichen Verwendung in Gebäuden und legt die anzuwendenden Prüfverfahren fest.
Dieses Dokument legt Anforderungen an die Leistungsfähigkeit sowie weitere Anforderungen an Festigkeit, Sicherheit, Dauerhaftigkeit, Leistung und Korrosionsbeständigkeit von Hangschlössern fest. Es legt eine Gebrauchsklasse, zwei Klassen für die Dauerhaftigkeit, sechs Klassen für die Korrosionsbeständigkeit und sechs Klassen für die Sicherheit fest.
In dieser Norm ist eine begrenzte manuelle Angriffsprüfung enthalten, da die maschinelle Prüfung nicht alle bekannten Möglichkeiten eines manuellen Angriffs nachbildet.
Die auf die Sicherheit bezogenen Anforderungen sind auf der Grundlage von Leistungsprüfungen, in denen Angriffe simuliert werden, in sechs Klassen eingeteilt.

Quincaillerie pour le bâtiment - Cadenas et porte-cadenas - Exigences et méthodes d'essai

Le présent document s’applique aux cadenas mécaniques et aux porte-cadenas normalement utilisés dans le bâtiment et il spécifie les méthodes d’essai à utiliser.
Le présent document spécifie les performances et autres exigences relatives à la résistance, à la sécurité des biens, l’endurance, au fonctionnement et à la résistance à la corrosion des cadenas. Il définit une catégorie d’utilisation, deux catégories d’endurance, six catégories pour la résistance à la corrosion et six grades pour la sécurité des biens.
L'essai d'attaque manuelle limitée est inclus dans la présente norme du fait que la machine d’essai ne reproduit pas toutes les attaques manuelles connues.
Les exigences relatives à la sécurité des biens sont classées suivant six grades, en fonction des résultats aux essais simulant une attaque.

Stavbno okovje - Obešanke in dodatki za obešanke - Zahteve in preskusne metode

Ta evropski standard obravnava mehanske obešanke in dodatke za obešanke za uporabo na stavbah in splošno uporabo ter določa preskusne metode, ki bodo uporabljene. Ta evropski standard določa lastnosti in druge zahteve glede trdnosti, varnosti, trajnosti, delovanja in odpornosti obešank na korozijo. Določa eno kategorijo uporabe, dve kategoriji trajnosti, šest kategorij odpornosti na korozijo in šest varnostnih stopenj na podlagi preskusov delovanja s simulacijo napada. V evropski standard je vključeno omejeno ročno preskušanje napada, ker strojno preskušanje ne ponovi vseh znanih ročnih napadov.

General Information

Status
Withdrawn
Public Enquiry End Date
17-Aug-2010
Publication Date
28-Aug-2013
Withdrawal Date
27-Dec-2021
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
28-Dec-2021
Due Date
20-Jan-2022
Completion Date
28-Dec-2021

Relations

Buy Standard

Standard
EN 12320:2013
English language
27 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stavbno okovje - Obešanke in dodatki za obešanke - Zahteve in preskusne metodeBaubeschläge - Hangschlösser und Hangschlossbeschläge - Anforderungen und PrüfverfahrenQuincaillerie pour le bâtiment - Cadenas et porte-cadenas - Exigences et méthodes d'essaiBuilding hardware - Padlocks and padlock fittings - Requirements and test methods91.190Stavbna opremaBuilding accessoriesICS:Ta slovenski standard je istoveten z:EN 12320:2012SIST EN 12320:2013en,fr,de01-oktober-2013SIST EN 12320:2013SLOVENSKI
STANDARDSIST EN 12320:20011DGRPHãþD



SIST EN 12320:2013



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12320
October 2012 ICS 91.190 Supersedes EN 12320:2001English Version
Building hardware - Padlocks and padlock fittings - Requirements and test methods
Quincaillerie pour le bâtiment - Cadenas et porte-cadenas -Exigences et méthodes d'essai
Baubeschläge - Hangschlösser und Hangschlossbeschläge - Anforderungen und Prüfverfahren This European Standard was approved by CEN on 11 August 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12320:2012: ESIST EN 12320:2013



EN 12320:2012 (E) 2 Contents
Page Foreword . 31Scope . 42Normative references . 43Terms and definitions . 44Requirements . 65Test methods . 86Classification . 167Marking . 17Annex A (normative)
Sampling and sequencing - Tests on alternative design padlocks . 18Annex B (normative)
Test rig illustrations . 19 SIST EN 12320:2013



EN 12320:2012 (E) 3 Foreword This document (EN 12320:2012) has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the latest by April 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12320:2001. The following is a list of technical changes since the previous edition: - Limited manual attack - Corrosion resistance - Table 2 – security requirements - Resistance to attack by plug/cylinder extraction - Annex A, sampling and sequencing The test methods are specified in detail to ensure reproducibility at any testing establishment within Europe, and the acceptance criteria are defined objectively to ensure consistency of assessment. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 12320:2013



EN 12320:2012 (E) 4
1 Scope
This European Standard applies to mechanical padlocks and padlock fittings used on buildings and general use and specifies the test methods to be used. This European Standard specifies performance and other requirements for strength, security, durability, performance, and corrosion resistance of padlocks. It establishes one category of use, two categories of durability, six categories for corrosion resistance and six grades for security based on performance tests that simulate attack. Limited manual attack testing is included in this European Standard because the machine testing does not replicate all known manual attacks. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1303:2005, Building hardware – Cylinders for locks – Requirements and test methods
EN 1670:2007, Building hardware – Corrosion resistance – Requirements and test methods EN 10025-2, Hot rolled products of structural steels – Part 2: Technical delivery conditions for non-alloy structural steels ISO 10899, High-speed steel two-flute twist drills – Technical specifications 3 Terms and definitions For the purposes of this document, the following terms and definitions and symbols apply. 3.1 Terms and definitions
3.1.1 cam part of the key and cylinder mechanism which operates the locking mechanism 3.1.2 effective key differ
difference between the key mechanism of similar design, achieved only by the movable detainer, which allows each key mechanism to be operated only by its own key Note 1 to entry: The number of effective differs is equal to the number of theoretical differs after deduction of the differs suppressed by the manufacturer due to technical constraints and those differs suppressed in accordance with the restraints of 4.5.1 3.1.3 hasp part of the padlock fitting which goes over the staple. SIST EN 12320:2013



EN 12320:2012 (E) 5 3.1.4 key mechanism part of the mechanism which recognises a correct key 3.1.5 locking mechanism part of the mechanism which is operated by the key mechanism to lock/unlock the padlock 3.1.6 padlock independent locking device comprising a body, a key mechanism, a locking mechanism and a shackle 3.1.7 padlock fitting device fitted to the object which is to be locked with a padlock excluding cables and chains 3.1.8 shackle part of the padlock which passes through and secures the padlock fitting 3.1.9 staple part of the padlock fitting through which the padlock shackle is passed. 3.2 Symbols
Table 1
Symbol Unit Definitiond mm Diameter of shackle F1 kN Push/pull force on cylinder plug/locking mechanism F2 kN Pull force on shackle or staple F3 kN Cutting force on shackle or staple F4 kN Maximum possible push/pull force on cylinder plug/locking mechanismh mm Height through which weight is dropped (impact test) M1 Nm Torque on key to test for interpassing M2 Nm Torque on cylinder plug/locking mechanism M3 Nm Twisting torque on shackle or staple n
Minimum number of effective key differs t min Drilling/sawing resistance time T °C Temperature of product for impact testing m g Drop mass for impact test SIST EN 12320:2013



EN 12320:2012 (E) 6 4 Requirements
4.1 General The structure of this clause reflects the classification as given in Clause 6.
4.2 Category of use (first classification digit)  Grade 1: according to requirements in 5.2 4.3 Durability (second classification digit)  Grade 0: no requirements  Grade 1: 10 000 cycles When tested in accordance with 5.3 it shall be possible to operate the padlock. The padlock fittings are excluded from the durability test. 4.4 Corrosion Resistance (third classification digit) Products shall be classified in accordance with EN 1670.  Grade 0: no defined corrosion resistance  Grade 1:
24h +1h/-0 h;  Grade 2:
48h +1h/-0 h;  Grade 3:
96h +1h/-0 h;
 Grade 4:
240h +1h/-0 h;  Grade 5: 480h +1h/-0 h; After the corrosion test, the padlock shall operate using a maximum torque on the key of 2.5 Nm. This corrosion test shall apply to the functionality only (not appearance). 4.5 Security (fourth classification digit) 4.5.1 General Some of the requirements can be confirmed with a certificate and test report according to EN 1303. In grades 4, 5 and 6 it shall not be possible to remove the key until the shackle is deadlocked in the closed position and the key retained in open position. 4.5.2 Minimum number of effective key differs
Padlocks shall have a minimum of n effective key differs (Table 2). For a mechanical padlock, the maximum number of steps on the same level shall be 60 %, maximum two adjacent and a minimum of three levels. SIST EN 12320:2013



EN 12320:2012 (E) 7 4.5.3 Non-interpassing of keys with just one interval effective differ
When tested in accordance with 5.5.2, it shall not be possible to operate the padlock with keys differing from the correct key by one interval, i.e. the next closest key. The next closest key shall be defined by the manufacturer according to its key coding system.
4.5.4 Resistance to force on cylinder plug or locking mechanism
When tested in accordance with 5.5.3, the cylinder plug or the locking mechanism shall resist a force F1 (Table 2).
4.5.5 Resistance to torque on cylinder plug or locking mechanism
When tested in accordance with 5.5.4, the cylinder plug or the locking mechanism shall resist a torque M2 (Table 2).
4.5.6 Resistance to pulling of shackle or staple
When tested in accordance with 5.5.5, the shackle and the staple shall each resist a force F2 (Table 2).
4.5.7 Resistance to twisting of shackle or staple
When tested in accordance with 5.5.6, the shackle and the staple shall each resist a torque M3 (Table 2).
4.5.8 Resistance to cutting of shackle or staple
When tested in accordance with 5.5.7, the shackle and the staple shall each resist a force F3 (Table 2).
4.5.9 Resistance to impact on padlock body, shackle and staple at low temperature
When tested in accordance with 5.5.8, the padlock body, the shackle and the staple cooled to temperature T, shall each resist the blows from the steel pole with the mass m and from the height h (Table 2). 4.5.10 Resistance to drilling of padlock body, shackle and staple
When tested in accordance with 5.5.9, the padlock body, the shackle and the staple shall each resist drilling for a time t (Table 2).
4.5.11 Resistance to sawing of padlock body, shackle and staple
When tested in accordance with 5.5.10, the padlock body, the shackle and the staple shall each resist sawing for a time t (Table 2).
4.5.12 Attack resistance
When tested in accordance with 5.5.11, the padlock shall resist attacks with manual tools for a time t (see Table 2).
SIST EN 12320:2013



EN 12320:2012 (E) 8 Table 2 — Security requirements Require-ment clause number Requirement Test method clause number Test parameter Grade Unit 1 2 3 4 5 6 4.5.1 Key retained in open position
yes / no - - - yes yes yes
4.5.2 Minimum number of effective key differs 5.5.1 n 300 1 0002 500 5 000 10 000 20 000- 4.5.3 Non-interpassing of keys with just one interval differ - Torque on key 5.5.2 M1 1 1 1,5 1,5 1,5 1,5 Nm 4.5.4 Resistance to force on cylinder plug or locking mechanism 5.5.3 F1 - - 4 5 10 15 kN 4.5.5 Resistance to torque on cylinder plug or locking mechanism 5.5.4 M2 - 2,5 5 15 20 30 Nm 4.5.6 Resistance to pulling of shackle and staple 5.5.5 F2 3 5 15 30 70 100 kN 4.5.7 Resistance to twisting of shackle and staple 5.5.6 M3 40 100 200 600
1 200 2 500 Nm 4.5.8 Resistance to cutting of shackle and staple 5.5.7 F3 6 15 25 45
70
100 kN 4.5.9 Resistance to impact on padlock body, shackle and staple at low temperature 5.5.8 T m h - - - - - - - 20 1 250 800 - 20 3 050 1 000 - 40 6 550 1 400 - 40 7 150 1 500 °C g mm 4.5.10 Resistance to drilling of padlock body, shackle and staple 5.5.9 t - - - 2 4 8 min 4.5.11 Resistance to sawing of padlock body, shackle
and staple 5.5.10 t - - - 2 4 8 min 4.5.12 Manual attack 5.5.11 t toolsets - - - 3 5 10 min NOTE Classification is in six grades where grade 1 has the lowest requirement. 5 Test methods
5.1 General 5.1.1 Introduction The manufacturer will provide assembly and component drawings to enable the tester to carry out a preliminary product assessment prior to testing. The padlock shall be tested in the locked position with the key removed.
It is not necessary for the correct key to operate the padlock after testing. Padlocks/ padlock fittings and their original keys shall be taken at random and submitted for each test.
In the event of one of the original two samples failing the test, the padlocks/ padlock fittings shall be deemed to have failed and a further two shall be tested, both of which shall pass the test.
SIST EN 12320:2013



EN 12320:2012 (E) 9 If the parts to be tested are inaccessible when the product is correctly mounted in accordance with the manufacturer's instructions, the product shall be considered to have passed that test.
A padlock shall be deemed to have been opened when a bar, of equal cross-section to that of its shackle, can be released. Ability to open can be checked at any time during the test by manipulation with a screwdriver or similar implement (maximum length 200 mm) for a period of 5 s max.
5.1.2 Tolerances Unless otherwise stated, the following tolerances shall apply :
 force ± 2 % ;
 torque ± 2 % ;
 mass/weight ± 2 % ;
 distance ± 2 % ;
 time ± 5 s ;
 temperature ± 2 °C.
Unless otherwise stated, the forces shall be applied progressively and without shock to the required load within 1 min.
5.1.3 Test environment The ambient temperature of the test environment shall be controlled throughout the test to 20 °C ± 5 °C unless otherwise stated.
5.1.4 Test tools
Specification of steel for cutting and impact tests as required in 5.5.7.1 and 5.5.8. shall be structural steel E335 defined in EN 10025-2, heat treated to have a hardness of 60 HRC to 64 HRC. 5.1.5 Sampling
Test sampling and sequencing shall be in accordance with Annex A.
5.2 Category of use
5.2.1 Operational unlocking test.
Mount the padlock in a suitable holding fixture, and apply a torque to a fully inserted correct key using a torque-meter, as shown in Figure B.1. At no point between locked and unlocked shall the torque exceed 1 Nm.
5.2.2 Key strength Requirements for key strength shall meet the requirements given in 5.2 of EN 1303:2005. SIST EN 12320:2013



EN 12320:2012 (E) 10 5.3 Durability The durability test shall be carried out using suitable apparatus that allows the full operational locking and unlocking sequence of the padlock to include the release of the shackle. (It is not necessary for the shackle to be turned). Repeat the sequence at a speed of 5 to 20 cycles per minute
During the operational cycle the key may remain partially inserted in the locking mechanism but shall have cleared all movable detainers. The key used for the durability test can be cleaned and the padlock shall be lubricated in accordance with the manufacturer’s instructions at the start of the test and after each 5000 cycles using the lubricant recommended by the manufacturer. After completing the required number of cycles the operation of the padlock shall be tested using a new original key. The rotation shall be achieved with a maximum torque of 1.5 Nm. If the padlock should jam and cease to operate during the test, then provided the padlock continues to operate in the proper manner when released, the test shall be allowed to continue. No durability requirements for padlock fittings. 5.4 Corrosion resistance
5.4.1 Preparation The padlock is locked on a staple which is mounted on a wooden block and placed in the chamber for salt spray test. The padlock without a key is oriented in the manner that it would assume to be in use. The padlock shall be exposed to a neutral salt spray test in accordance with EN 1670.  Grade 0:
no defined corrosion resistance;  Grade 1:
24h +1h/-0 h;  Grade 2:
48h +1h/-0 h;  Grade 3:
96h +1h/-0 h;
 Grade 4:
240h +1h/-0 h;  Grade 5: 480h +1h/-0 h. 5.4.2 Test of padlock function after salt spray exposure The evaluation shall be made in accordance with EN 167
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.