SIST EN ISO 22526-1:2022

SLOVENSKI STANDARD
SIST EN ISO 22526-1:2022
01-januar-2022
Polimerni materiali - Ogljični in okoljski odtis polimernih materialov na biološki
osnovi - 1. del: Splošna načela (ISO 22526-1:2020)
Plastics - Carbon and environmental footprint of biobased plastics - Part 1: General
principles (ISO 22526-1:2020)
Kunststoffe - Kohlenstoff- und Umweltbilanz von biobasierten Kunststoffen - Teil 1:
Allgemeine Grundlagen (ISO 22526 1:2020)
Plastiques - Empreinte carbone et environnementale des plastiques biosourcés - Partie
1: Principes généraux (ISO 22526-1:2020)
Ta slovenski standard je istoveten z: EN ISO 22526-1:2021
ICS:
13.020.40 Onesnaževanje, nadzor nad Pollution, pollution control
onesnaževanjem in and conservation
ohranjanje
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 22526-1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 22526-1:2022

---------------------- Page: 2 ----------------------
SIST EN ISO 22526-1:2022


EN ISO 22526-1
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2021
EUROPÄISCHE NORM
ICS 13.020.40; 83.080.01
English Version

Plastics - Carbon and environmental footprint of biobased
plastics - Part 1: General principles (ISO 22526-1:2020)
Plastiques - Empreinte carbone et environnementale Kunststoffe - Kohlenstoff- und Umweltbilanz von
des plastiques biosourcés - Partie 1: Principes biobasierten Kunststoffen - Teil 1: Allgemeine
généraux (ISO 22526-1:2020) Grundlagen (ISO 22526 1:2020)
This European Standard was approved by CEN on 8 November 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22526-1:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 22526-1:2022
EN ISO 22526-1:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 22526-1:2022
EN ISO 22526-1:2021 (E)
European foreword
The text of ISO 22526-1:2020 has been prepared by Technical Committee ISO/TC 61 "Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 22526-1:2021
by Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2022, and conflicting national standards shall be
withdrawn at the latest by May 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 22526-1:2020 has been approved by CEN as EN ISO 22526-1:2021 without any
modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 22526-1:2022

---------------------- Page: 6 ----------------------
SIST EN ISO 22526-1:2022
INTERNATIONAL ISO
STANDARD 22526-1
First edition
2020-01
Plastics — Carbon and environmental
footprint of biobased plastics —
Part 1:
General principles
Reference number
ISO 22526-1:2020(E)
©
ISO 2020

---------------------- Page: 7 ----------------------
SIST EN ISO 22526-1:2022
ISO 22526-1:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 22526-1:2022
ISO 22526-1:2020(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General principles . 2
5 Carbon and environmental footprint of biobased plastics . 2
5.1 Principle . 2
5.2 Material carbon footprint . 2
5.3 Process carbon footprint . 5
5.4 Environmental (total) footprint (life cycle assessment) . 5
5.5 System boundaries of the ISO 22526 series . 5
Bibliography . 7
© ISO 2020 – All rights reserved iii

---------------------- Page: 9 ----------------------
SIST EN ISO 22526-1:2022
ISO 22526-1:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 14,
Enviromental aspects.
A list of all parts in the ISO 22526 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 22526-1:2022
ISO 22526-1:2020(E)

Introduction
Increased use of biomass resources for manufacturing plastic products can be effective in reducing
global warming and the depletion of fossil resources.
Current plastic products are composed of biobased synthetic polymers, fossil-based synthetic polymers,
natural polymers and additives that can include biobased materials.
Biobased plastics refer to plastics that contain materials wholly or partly of biogenic origin.
© ISO 2020 – All rights reserved v

---------------------- Page: 11 ----------------------
SIST EN ISO 22526-1:2022

---------------------- Page: 12 ----------------------
SIST EN ISO 22526-1:2022
INTERNATIONAL STANDARD ISO 22526-1:2020(E)
Plastics — Carbon and environmental footprint of
biobased plastics —
Part 1:
General principles
1
...