Graphic technology - Methods of adjustment of the colour reproduction of a printing system to match a set of characterization data

This Technical Specification specifies three methods for the adjustment of the digital content data that is input to a printing system to achieve consistency in the printed results among a number of presses printing to the same general aim conditions. These three methods are generally identified as a) the matching of tone value curves, b) the use of near-neutral scales, and c) the use of CMYK to CMYK multi-dimensional transforms. The procedures for establishing the aim condition for the necessary transfer curves, the procedures for determining the individual transfer curves, and a comparison of the applicability of these three methods are included. These adjustment procedures are applicable to printing systems that use CMYK colourants but are not restricted to those that use traditional ink on paper printing but can involve other marking technologies such as those used for proofing and/or digital printing.

Technologie graphique - Méthodes d'ajustage de la reproduction de couleurs d'un système d'impression pour correspondre à un ensemble de données de caractérisation

Grafična tehnologija - Metode za prilagajanje barvne reprodukcije na tiskarskem sistemu, da ustreza želenim karakterističnim vrednostim

Ta tehnična specifikacija določa tri metode za prilagajanje digitalnih vsebinskih podatkov, ki se vnašajo v tiskarski sistem, za doseganje doslednosti natisnjenih rezultatov med številnimi tiskarskimi stroji, ki tiskajo pod istimi splošnimi ciljnimi pogoji. Te tri metode se v splošnem označujejo kot a) prilagajanje krivulj vrednosti tona, b) uporaba skoraj nevtralnih lestvic, in c) uporaba večdimenzionalnih transformacij iz CMYK v CMYK. Vključeni so postopki za vzpostavljanje ciljnih pogojev za potrebne krivulje prenosa, postopki za določanje posameznih krivulj prenosa in primerjava uporabnosti teh treh metod. Postopki prilagajanja veljajo za tiskarske sisteme, ki uporabljajo barvila CMYK, a niso omejeni na sisteme, ki uporabljajo tradicionalno tiskanje barve na papir, pač pa lahko vključujejo druge označevalne tehnologije, kot so tiste, ki se uporabljajo za poskusno in/ali digitalno tiskanje.

General Information

Status
Withdrawn
Publication Date
08-Apr-2010
Withdrawal Date
24-Jan-2024
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
19-Jan-2024
Due Date
11-Feb-2024
Completion Date
25-Jan-2024

Relations

Buy Standard

Technical specification
TS ISO/TS 10128:2010
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Technical specification
ISO/TS 10128:2009 - Graphic technology -- Methods of adjustment of the colour reproduction of a printing system to match a set of characterization data
English language
12 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TS ISO/TS 10128:2010
01-maj-2010
*UDILþQDWHKQRORJLMD0HWRGH]DSULODJDMDQMHEDUYQHUHSURGXNFLMHQDWLVNDUVNHP
VLVWHPXGDXVWUH]DåHOHQLPNDUDNWHULVWLþQLPYUHGQRVWLP
Graphic technology - Methods of adjustment of the colour reproduction of a printing
system to match a set of characterization data
Technologie graphique - Méthodes d'ajustage de la reproduction de couleurs d'un
système d'impression pour correspondre à un ensemble de données de caractérisation
Ta slovenski standard je istoveten z: ISO/TS 10128:2009
ICS:
37.100.10 Reprodukcijska oprema Reproduction equipment
SIST-TS ISO/TS 10128:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TS ISO/TS 10128:2010

---------------------- Page: 2 ----------------------

SIST-TS ISO/TS 10128:2010

TECHNICAL ISO/TS
SPECIFICATION 10128
First edition
2009-07-01

Graphic technology — Methods of
adjustment of the colour reproduction of
a printing system to match a set of
characterization data
Technologie graphique — Méthodes d'ajustage de la reproduction de
couleurs d'un système d'impression pour correspondre à un ensemble
de données de caractérisation




Reference number
ISO/TS 10128:2009(E)
©
ISO 2009

---------------------- Page: 3 ----------------------

SIST-TS ISO/TS 10128:2010
ISO/TS 10128:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 4 ----------------------

SIST-TS ISO/TS 10128:2010
ISO/TS 10128:2009(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Procedures .3
4.1 General.3
4.2 Matching of tone value curves .4
4.3 Use of near-neutral scales .5
4.4 Use of CMYK to CMYK multi-dimensional transforms .7
5 Applicability of each method.8
Annex A (normative) Tone value .9
Bibliography .
...

TECHNICAL ISO/TS
SPECIFICATION 10128
First edition
2009-07-01

Graphic technology — Methods of
adjustment of the colour reproduction of
a printing system to match a set of
characterization data
Technologie graphique — Méthodes d'ajustage de la reproduction de
couleurs d'un système d'impression pour correspondre à un ensemble
de données de caractérisation




Reference number
ISO/TS 10128:2009(E)
©
ISO 2009

---------------------- Page: 1 ----------------------
ISO/TS 10128:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/TS 10128:2009(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Procedures .3
4.1 General.3
4.2 Matching of tone value curves .4
4.3 Use of near-neutral scales .5
4.4 Use of CMYK to CMYK multi-dimensional transforms .7
5 Applicability of each method.8
Annex A (normative) Tone value .9
Bibliography .12

© ISO 2009 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/TS 10128:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technic
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.