SIST EN 848-3:2007+A2:2009

Oznaka standarda: SIST EN 848-3:2007+A2:2009
Koda projekta: 00142114
Organizacija: SIST
Naslov (angleški): Safety of woodworking machines - One side moulding machines with rotating tools - Part 3: Numerically controlled (NC) boring and routing machines
Naslov (slovenski): Varnost lesnoobdelovalnih strojev - Rezkalniki z vrtilnim orodjem za enostransko obdelavo - 3. del: Numerično krmiljeni (NC) vrtalni in rezkalni stroji
Če kupite standardizacijski dokument v .pdf formatu prek spletne prodaje, vam nudimo 20% popust pri spodnji ceni brez DDV. Cenik SIST
Dokumenti
Ime Jezik Status Cena Dodaj v košarico
SIST EN 848-3:2007+A2:2009 angleški jezik Withdrawn SIST-M: 108.90 EUR
PDF
Papir
Tehnični odbor: VSN - Varnost strojev in naprav
ICS: 25.040.20 79.120.10
Status: Razveljavljen
Objavljen: 01-dec-2009
Refer. št. objave: Sporočila 2009-12
Razveljavitev: 01-dec-2012
Referenca razveljavitve: Sporočila 2012-12
Področje projekta (angleško): This document specifies all significant hazards, hazardous situations and events as listed in Clause 4, which are relevant to NC boring machines, NC routing machines and NC combined boring/routing machines (as defined in 3.2.1) herein after referred to as "machines" designed to cut solid wood, chip board, fibreboard, plywood and also these materials where these are covered with plastic laminate or edgings when they are used as intended and under the conditions foreseen by the manufacturer. This document also applies to machines fitted with: a) additional equipment for sawing, sanding and edge banding; b) fixed or movable workpiece support; c) mechanical, pneumatic, hydraulic or vacuum workpiece clamping; d) automatic tool change facilities. This document does not deal with the specific hazards of edge banding equipment fitted to NC boring machines, NC routing machines and NC combined boring/routing machines. This document is only applicable to NC boring machines, NC routing machines and NC combined boring/routing machines which are designed to use milling tools with a cutting circle diameter below 16 mm or milling tools or saw-blades conforming to EN 847-1:2005 and EN 847-2:2001 and boring tools or sanding wheels. This document is not applicable to NC boring machines, NC routing machines and NC combined boring/routing machines which are designed to use grinding wheels. This document is not applicable to single spindle hand fed/integrated fed routing machines. NOTE Single spindle hand fed/integrated fed routing machines are dealt with in EN 848-2:2007. This document does not deal with the specific hazards of ejection through curtains on machines with feeding openings of which the distance between the workpiece support and the lower part of the partial enclosure in the direction of the feed exceeds 400 mm. This document is not applicable to NC boring machines, NC routing machines and NC combined boring/routing machines which are manufactured before the d
Povezava na standarde
Povezava Ime Datum
Nadomešča SIST EN 848-3:2007 - Varnost lesnoobdelovalnih strojev - Rezkalniki z vrtilnim orodjem za enostransko obdelavo - 3. del: Numerično krmiljeni (NC) vrtalni in rezkalni stroji 01-dec-2009
Nadomeščen z SIST EN 848-3:2012 - Varnost lesnoobdelovalnih strojev - Rezkalni stroji z vrtečim orodjem za enostransko obdelavo - 3. del: Numerično krmiljeni (NC) vrtalni in rezkalni stroji 01-dec-2012
Konsolidira SIST EN 848-3:2007/kprA1:2009 - Varnost lesnoobdelovalnih strojev - Rezkalniki z vrtilnim orodjem za enostransko obdelavo - 3. del: Numerično krmiljeni (NC) vrtalni in rezkalni stroji 01-dec-2009


• Slovenski standardi SIST s cenovnim razredom AC so popravki standardov in so v večini primerov brezplačni.

• Slovenski standardi SIST s cenovnim razredom AP so privzeti tuji standardi, katerih sestavni del je izvirni standard, ki ga moramo pridobiti pri izdajatelju v tujini. Naročilo pošljite na: prodaja@sist.si.

Najbolje prodajani standardi