SIST EN ISO 5182:2016

SLOVENSKI STANDARD
SIST EN ISO 5182:2016
01-november-2016
1DGRPHãþD
SIST EN ISO 5182:2011
Uporovno varjenje - Materiali za elektrode in pomožno opremo (ISO 5182:2016)
Resistance welding - Materials for electrodes and ancillary equipment (ISO 5182:2016)
Widerstandsschweißen - Werkstoffe für Elektroden und Hilfseinrichtungen (ISO
5182:2016)
Soudage par résistance - Matériaux pour électrodes et équipements annexes (ISO
5182:2016)
Ta slovenski standard je istoveten z: EN ISO 5182:2016
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
SIST EN ISO 5182:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 5182:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 5182:2016


EN ISO 5182
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2016
EUROPÄISCHE NORM
ICS 25.160.20 Supersedes EN ISO 5182:2009
English Version

Resistance welding - Materials for electrodes and ancillary
equipment (ISO 5182:2016)
Soudage par résistance - Matériaux pour électrodes et Widerstandsschweißen - Werkstoffe für Elektroden
équipements annexes (ISO 5182:2016) und Hilfseinrichtungen (ISO 5182:2016)
This European Standard was approved by CEN on 23 August 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5182:2016 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 5182:2016
EN ISO 5182:2016 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 5182:2016
EN ISO 5182:2016 (E)
European foreword
This document (EN ISO 5182:2016) has been prepared by Technical Committee ISO/TC 44 “Welding
and allied processes” in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2017, and conflicting national standards
shall be withdrawn at the latest by February 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 5182:2009.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 5182:2016 has been approved by CEN as EN ISO 5182:2016 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 5182:2016

---------------------- Page: 6 ----------------------

SIST EN ISO 5182:2016
INTERNATIONAL ISO
STANDARD 5182
Fourth edition
2016-08-01
Resistance welding — Materials for
electrodes and ancillary equipment
Soudage par résistance — Matériaux pour électrodes et
équipements annexes
Reference number
ISO 5182:2016(E)
©
ISO 2016

---------------------- Page: 7 ----------------------

SIST EN ISO 5182:2016
ISO 5182:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 5182:2016
ISO 5182:2016(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 1
4.1 Group A — Copper and copper alloys . 1
4.2 Group B — Sintered materials . 1
4.3 Group C — Dispersion-strengthened copper (DSC) alloys . 2
5 Specifications . 2
5.1 Requirements . 2
5.2 Chemical composition . 2
5.3 Mechanical properties . 2
5.4 Electrical properties . 2
6 Methods of test . 2
6.1 Vickers hardness test. 2
6.2 Electrical properties . 2
6.3 Softening temperature test . 3
7 Designation . 3
8 Application . 3
9 Hardness conversions . 3
Annex A (informative) Typical applications . 6
Annex B (informative) Hardness conversion . 9
Annex C (informative) Corresponding national designations .10
Bibliography .11
© ISO 2016 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 5182:2016
ISO 5182:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 44, Welding and allied processes, Subcommittee
SC 6, Resistance welding and allied mechanical joining.
This fourth edition cancels and replaces the third edition (ISO 5182:2008), which has been technically
revised.
Requests for official interpretations of any aspect of this International Standard should be directed to
the Secretariat of ISO/TC 44 via your national standards body. A complete listing of these bodies can be
found at www.iso.org.
iv © ISO 2016 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 5182:2016
INTERNATIONAL STANDARD ISO 5182:2016(E)
Resistance welding — Materials for electrodes and
ancillary equipment
1 Scope
This International Standard specifies the characteristics of materials for resistance welding electrodes
and ancillary equipment which are used for carrying current and transmitting force to the work.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 6507-1, Metallic materials — Vickers hardness test — Part 1: Test method
ASTM E1004, Standard practice for determining electrical conductivity using the electromagnetic (eddy-
current) method
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
softening temperature
maximum temperature that, if maintained for 2 h, will result in a reduction in ambient temperature
hardness of a maximum of 15 % of the “as received” value
4 Classification
4.1 Group A — Copper and copper alloys
This group defines four types of material in accordance with Table 1.
Table 1 — Group A — Classification of copper and copper alloys
Type Description
Non-heat-treatable alloys of high conductivity and medium hardness, the wrought forms of
1
which are given their strengths by cold working during manufacture.
Alloys which are harder than type 1 and in which the mechanical properties have been devel-
2 oped by heat treatment during manufacture or by a combination of heat treatment and cold
working.
Heat-treated alloys which have superior mechanical properties to type 2 but a lower electrical
3
conductivity than either type 1 or type 2.
Alloys having certain specialised properties which may, in some cases, be obtained either by
4 cold working or by heat treatment. Alloys of this type are not necessarily interchangeable with
each other.
4.2 Group B — Sintered materials
This group comprises six types of ma
...