iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 12809:2003/AC:2004

(Amendment)

Residential independent boilers fired by solid fuel - Nominal heat output up to 50 kW - Requirements and test methods

Residential independent boilers fired by solid fuel - Nominal heat output up to 50 kW - Requirements and test methods

Specifies requirements relating to the design, manufacture, construction, performance (efficiency and emission), safety, instructions and marking together with associated test methods and test fuels for type testing residential independent heating and hot water boilers fired by solid fuel.

Heizkessel für feste Brennstoffe - Nennwärmeleistung bis 50 kW - Anforderungen und Prüfung

Chaudieres domestiques a combustible solide destinées a etre implantées dans le volume habitable - Puissance calorifique nominale inférieure ou égale a 50 kW - Exigences et méthodes d'essai

Ogrevalni kotli na trdna goriva - Nazivna toplotna moč do 50 kW - Zahteve in preskusne metode - Dopolnilo AC

General Information

Status
Withdrawn
Publication Date
31-Dec-2003
Withdrawal Date
31-Oct-2006
ICS
91.140.10 - Central heating systems
97.100.30 - Solid fuel heaters
Technical Committee
OGS - Heating for buildings
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Nov-2006
Due Date
01-Nov-2006
Completion Date
01-Nov-2006
Directive
89/106/EEC - Construction products
Mandate
M/129 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on space heating appliances
Ref Project
EN 12809:2001/AC:2003 - Residential independent boilers fired by solid fuel - Nominal heat output up to 50 kW - Requirements and test methods

Relations

Replaced By
SIST EN 12809:2003/AC:2006 - Residential independent boilers fired by solid fuel - Nominal heat output up to 50 kW - Requirements and test methods
Effective Date
01-Nov-2006
Replaced By
SIST EN 16510-1:2023 - Residential solid fuel burning appliances - Part 1: General requirements and test methods
Effective Date
28-Dec-2022
Replaced By
SIST EN 16510-2-4:2023 - Residential solid fuel burning appliances - Part 2-4: Independent boilers - Nominal heat output up to 50 kW
Effective Date
28-Dec-2022
Corrects
SIST EN 12809:2003 - Residential independent boilers fired by solid fuel - Nominal heat output up to 50 kW - Requirements and test methods
Effective Date
01-Jan-2004
Corrects
SIST EN 12809:2003 - Residential independent boilers fired by solid fuel - Nominal heat output up to 50 kW - Requirements and test methods
Effective Date
08-Jun-2022

Buy Standard

EN 12809:2003/AC:2004EN 12809:2003/AC:2004
PreviousNext
Corrigendum
EN 12809:2003/AC:2004
English and German language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Heizkessel für feste Brennstoffe - Nennwärmeleistung bis 50 kW - Anforderungen und PrüfungChaudieres domestiques a combustible solide destinées a etre implantées dans le volume habitable - Puissance calorifique nominale inférieure ou égale a 50 kW - Exigences et méthodes d'essaiResidential independent boilers fired by solid fuel - Nominal heat output up to 50 kW - Requirements and test methods97.100.30Grelniki na trdo gorivoSolid fuel heaters91.140.10Sistemi centralnega ogrevanjaCentral heating systemsICS:Ta slovenski standard je istoveten z:EN 12809:2001/AC:2003SIST EN 12809:2003/AC:2004en,de01-januar-2004SIST EN 12809:2003/AC:2004SLOVENSKI
STANDARD



SIST EN 12809:2003/AC:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12809:2001/ACSeptember 2003Septembre 2003September 2003ICSEnglish versionVersion FrançaiseDeutsche FassungResidential independent boilers fired by solid fuel - Nominal heat output upto 50 kW - Requirements and test methodsChaudières domestiques à combustiblesolide destinées à être implantées dans levolume habitable - Puissance calorifiquenominale inférieure ou égale à 50 kW -Exigences et méthodes d'essaiHeizkessel für feste Brennstoffe -Nennwärmeleistung bis 50 kW -Anforderungen und PrüfungThis corrigendum becomes effective on 17 September 2003 for incorporation in the official Germanand En
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
oSIST prEN 12809:2011(Main)
Residential independent boilers fired by solid fuel - Nominal heat output up to 50 kw - Requirements and test methods
prEN 12809

This European Standard specifies requirements relating to the design, manufacture, construction, performance (efficiency and emission), safety, instructions and marking together with associated test methods and test fuels for type testing residential independent boilers fired by solid fuel.
This standard is applicable to hand and automatically fired appliances having nominal heat outputs up to 50 kW, the primary function of which is to provide hot water for central heating and/or domestic use, and which are designed for use only with open vented systems at a working pressure not exceeding 2 bar. In addition to their primary function of providing hot water these appliances also provide space heating to the place of installation. These appliances may burn either solid mineral fuels, peat briquettes or natural or manufactured wood logs or be multi-fuel in accordance with the appliance manufacturer’s instructions.
This standard is not applicable to independent boilers for hot water only production and having heat outputs of less than 5 kW.
This standard is also not applicable to the design and construction of automatic stoking devices.

  • Draft
    82 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 303-5:2021+A1:2023(Main)
Heating boilers - Part 5: Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW - Terminology, requirements, testing and marking
EN 303-5:2021+A1:2022

1.1 General
This European Standard applies to heating boilers including safety devices up to a nominal heat output of 500 kW which are designed for the burning of solid fuels only and are operated according to the instructions of the boiler manufacturer.
This European Standard deals with significant hazards, hazardous situations and events relevant to heating boilers used as intended and under the conditions foreseen by the manufacturer (see Clause 4).
The boilers may operate under natural draught or forced draught. The stoking may work manually or automatically.
The boilers may operate under room sealed conditions in case of supervised under pressure in the combustion chamber.
The boilers may operate in condensing condition.
NOTE This European Standard deals with boilers which are both within and outside of the scope of the Machinery
Directive 2006/42/EC.
This European Standard contains requirements and test methods for safety, combustion quality, operating characteristics, marking and maintenance of heating boilers and secondary emission reduction appliances and efficiency improvement appliances. It also covers all external equipment that influences the safety systems (e.g. back burning safety device, integral fuel hopper).
This European Standard covers only boilers that include burners as a unit. The standard applies to the combination of a boiler body with a solid fuel burner according to EN 15270 as a unit only when the whole unit is tested in accordance with this European Standard.
Heating boilers in accordance with this European Standard are designed for central heating installations where the heat carrier is water and the maximum allowable temperature is 110 °C, and which can operate at a maximum allowable operating pressure of 6 bars. For heating boilers with a built-in or attached water heater (storage or continuous flow heater), this European Standard only applies to those parts of the water heater which are necessarily subject to the operating conditions of the heating boiler (heating part).
This European Standard does not apply to:
heating boilers and other heating appliances which are also designed for the direct heating of the place of installation;
cooking appliances;
the design and construction of external fuel storage and transportation devices prior to the safety devices of the boiler;
room sealed applications above a nominal heat output > 70 kW or operated with positive pressure in the combustion chamber or operated under natural draught;
This European Standard specifies the necessary terminology for solid fuel heating boilers, the control and safety related requirements, the design requirements, the technical heating requirements (taking into account the environmental requirements) and testing, as well as the marking requirements.
This European Standard is not applicable to heating boilers which are tested before the date of its publication as an EN (European Standard).
1.2 Fuels
These boilers may burn either fossil fuels, biogenic fuels or other fuels such as peat, as specified for their use by the boiler manufacturer, in accordance with the requirements of this European Standard.
Solid fuels included in this European Standard are categorised as follows.
1.2.1 Biogenic fuels
Biomass in a natural state, in the form of:
Adaptation to new fuels standards and consideration of new fuels standards in preparation.
A log wood with moisture content w ≤ 25 %, according to EN 14961-5;
B1 chipped wood (wood chipped by machine, usually up to a maximum length of 15 cm) with moisture content from w 15 % to w 35 %, according to EN 14961-4;
B2 chipped wood as under B1, except with moisture content w > 35 %;
C1 compressed wood (e.g. pellets without additives, made of wood and/or bark particles; natural binding agents such as molasses, vegetable paraffins and starch are permitted), pellets according to EN 14961-2;
(...)

  • Standard
    103 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 12809:2011(Main)
Residential independent boilers fired by solid fuel - Nominal heat output up to 50 kw - Requirements and test methods
prEN 12809

This European Standard specifies requirements relating to the design, manufacture, construction, performance (efficiency and emission), safety, instructions and marking together with associated test methods and test fuels for type testing residential independent boilers fired by solid fuel.
This standard is applicable to hand and automatically fired appliances having nominal heat outputs up to 50 kW, the primary function of which is to provide hot water for central heating and/or domestic use, and which are designed for use only with open vented systems at a working pressure not exceeding 2 bar. In addition to their primary function of providing hot water these appliances also provide space heating to the place of installation. These appliances may burn either solid mineral fuels, peat briquettes or natural or manufactured wood logs or be multi-fuel in accordance with the appliance manufacturer’s instructions.
This standard is not applicable to independent boilers for hot water only production and having heat outputs of less than 5 kW.
This standard is also not applicable to the design and construction of automatic stoking devices.

  • Draft
    82 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN ISO/TS 16486-7:2023(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 7: Assessment of conformity (ISO/TS 16486-7:2023)
CEN ISO/TS 16486-7:2023

This document gives guidance and requirements for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of the ISO 16486 series which are intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1    A basic test matrix in Annex B provides an overview of the testing scheme.
It is recommended for the manufacturer to have a management system such as ISO 9001[4] or equivalent.
NOTE 2    If certification is involved, certification bodies and inspection bodies operating according to ISO/IEC 17065 and ISO/IEC 17020 are considered to be competent.
In conjunction with the other parts of the ISO 16486 series (see Clause 2), this document is applicable to unplasticized polyamide (PA-U) piping systems intended to be buried and used for the supply of gaseous fuels. It is applicable to PA-U pipes, fittings and valves, as well as to their joints and to joints with components of other materials intended to be used under the following conditions:
a)    a maximum operating pressure (MOP) up to and including 18 bar[1] (the MOP is limited to 16 bar for CEN member countries, where ISO 16486-6 is replaced by CEN/TS 12007-6[1]);
b)    an operating temperature of 20 °C as the reference temperature.
NOTE 3    For operating temperatures different to 20 °C, derating coefficients can be used (see ISO 16486-6). CEN member countries use CEN/TS 12007-6[1] and ISO/TS 16486-7 (this document) as a basis, but they can also request additional requirements. For non-CEN member countries, information for dealing with special cases for PA-U can be found in ISO/TS 16486-7 (this document) and PPI TR-3.[7]
For mechanical fittings conforming to ISO 17885, guidance for assessment of conformity is not given in this document. When requested, a quality plan based on the tests mentioned can be set up in agreement between user and manufacturer.
The ISO 16486 series covers a range of maximum operating pressures and gives requirements concerning colours.
NOTE 4    It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

  • Technical specification
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 301 406-2 V3.1.1:2023(Main)
Digital Enhanced Cordless Telecommunications (DECT) - Harmonised Standard for access to radio spectrum - Part 2: DECT-2020 NR
ETSI EN 301 406-2 V3.1.1 (2023-08)

DEN/DECT-00359-2

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    76 pages
    English language
    sale 15% off
  • Standard
    76 pages
    English language
    sale 15% off
  • Draft
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60061-3:2000/A59:2023(Main)
Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 3: Gauges (IEC 60061-3:1969/AMD59:2023)
EN 60061-3:1993/A59:2023
  • Amendment
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16186-5:2021+A1:2023(Main + Amendment)
Railway applications - Driver's cabs - Part 5: External visibility for tram vehicles
EN 16186-5:2021+A1:2023

This document specifies the external front and rear visibility conditions from cabs of tram
vehicles and the associated assessment method.
This document applies to vehicles operating on tram networks.
This document does not apply to driver's auxiliary desks.
This standard is not intended to be applied for tram train.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60061-2:1999/A59:2023(Main)
Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 2: Lampholders (IEC 60061-2:1969/AMD59:2023)
EN 60061-2:1993/A59:2023
  • Amendment
    19 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST IEC 60050-811:2023/A1:2023(Amendment)
Amendment 1: International Electrotechnical Vocabulary (IEV) - Part 811: Electric traction
IEC 60050-811:2017/AMD1:2021
  • Standard
    3 pages
    English and French language
    sale 15% off
  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60721-3-4:2019/AC:2023(Corrigendum)
Classification of environmental conditions - Part 3-4: Classification of groups of environmental parameters and their severities - Stationary use at non-weatherprotected locations (IEC 60721-3-4:2019/COR1:2023)
EN IEC 60721-3-4:2019/AC:2023-08
  • Corrigendum
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day