SIST EN ISO 5457:2002/Amd1:2010

SLOVENSKI STANDARD
SIST EN ISO 5457:2002/oprA1:2009
01-maj-2009
7HKQLþQDGRNXPHQWDFLMDL]GHONRY9HOLNRVWLLQXUHGLWHYULVDOQLKOLVWRY'RSROQLOR
,62'$PG
Technical product documentation - Sizes and layout of drawing sheets - Amendment 1
(ISO 5457:1999/DAmd 1:2009)
Technische Produktdokumentation - Formate und Gestaltung von Zeichnungsvordrucken
- Amendment 1 (ISO 5457:1999/DAmd 1:2009)
Documentation technique de produits - Formats et présentation des éléments
graphiques des feuilles de dessin - Amendment 1 (ISO 5457:1999/DAmd 1:2009)
Ta slovenski standard je istoveten z: EN ISO 5457:1999/prA1
ICS:
01.100.01 7HKQLþQRULVDQMHQDVSORãQR Technical drawings in
general
SIST EN ISO 5457:2002/oprA1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 5457:2002/oprA1:2009

---------------------- Page: 2 ----------------------
SIST EN ISO 5457:2002/oprA1:2009
EUROPEAN STANDARD
DRAFT
EN ISO 5457:1999
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
February 2009
ICS 01.100.01

English Version
Technical product documentation - Sizes and layout of drawing
sheets - Amendment 1 (ISO 5457:1999/DAmd 1:2009)
Documentation technique de produits - Formats et Technische Produktdokumentation - Formate und
présentation des éléments graphiques des feuilles de Gestaltung von Zeichnungsvordrucken (ISO
dessin - Amendement 1 (ISO 5457:1999/DAmd 1:2009) 5457:1999/DAmd 1:2009)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/SS F01.
This draft amendment A1, if approved, will modify the European Standard EN ISO 5457:1999. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5457:1999/prA1:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 5457:2002/oprA1:2009
EN ISO 5457:1999/prA1:2009 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 5457:2002/oprA1:2009
EN ISO 5457:1999/prA1:2009 (E)
Foreword
This document (EN ISO 5457:1999/prA1:2009) has been prepared by Technical Committee ISO/TC 10
"Technical drawings, product definition and related documentation" in collaboration with Technical Committee
CEN/SS F01 "Technical drawings", the secretariat of which is held by CMC.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 5457:1999/DAmd1 has been approved by CEN as a EN ISO 5457:1999/prA1:2009 without
any modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 5457:2002/oprA1:2009

---------------------- Page: 6 ----------------------
SIST EN ISO 5457:2002/oprA1:2009
DRAFT AMENDMENT ISO 5457:1999/DAmd 1
ISO/TC 10/SC 1 Secretariat: SN
Voting begins on: Voting terminates on:
2009-02-19 2009-07-19
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Technical product documentation — Sizes and layout of drawing
sheets
AMENDMENT 1
Documentation technique de produits — Formats et présentation des éléments graphiques des feuilles de
dessin
AMENDEMENT 1
ICS 01.100.01

ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing a
...