Fixed capacitors for use in electronic equipment - Part 2: Sectional specification - Fixed metallized polyethylene-terephthalate film dielectric DC capacitors (IEC 60384-2:2021)

This part of IEC 60384 applies to fixed capacitors for direct current, with metallized electrodes
and polyethylene-terephthalate dielectric for use in electronic equipment.
These capacitors have a possibility of "self-healing properties" depending on conditions of use.
They are primarily intended for applications where the AC component is small with respect to
the rated voltage. Two performance grades of capacitors are covered: grade 1 for long-life
application and grade 2 for general application.
Capacitors for electromagnetic interference suppression and surface mount fixed metallized
polyethylene-terephthalate film dielectric DC capacitors are not included, but are covered by
IEC 60384-14 and IEC 60384-19, respectively.
The object of this document is to prescribe preferred ratings and characteristics and to select
from IEC 60384-1 the appropriate quality assessment procedures, tests and measuring
methods, and to give general performance requirements for this type of capacitor. Test
severities and requirements prescribed in detail specifications referring to this sectional
specification are of equal or higher performance level, because lower performance levels are
not permitted.

Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 2: Rahmenspezifikation - Festkondensatoren mit metallisierter Kunststofffolie aus Polyethylen-Terephthalat für Gleichspannung (IEC 60384-2:2021)

Condensateurs fixes utilisés dans les équipements électroniques - Partie 2: Spécification intermédiaire - Condensateurs fixes pour courant continu à diélectrique en film de téréphtalate de polyéthylène métallisé (IEC 60384-2:2021)

L’IEC 60384-2:2021 s’applique aux condensateurs fixes pour courant continu, avec des électrodes métallisées et des diélectriques en téréphtalate de polyéthylène et utilisés dans des équipements électroniques.
Ces condensateurs ont potentiellement des “propriétés autocicatrisantes” selon les conditions d’utilisation. Ils sont principalement destinés aux applications dont la composante de courant alternatif est négligeable par rapport à la tension assignée. Deux classes de performance de condensateurs sont couvertes: la Classe 1 pour des applications longue durée et la Classe 2 pour une application courante.
Les condensateurs d’antiparasitage et les condensateurs fixes pour courant continu à diélectrique en film de téréphtalate de polyéthylène métallisé pour montage en surface n’en font pas partie, mais sont respectivement couverts par l’IEC 60384-14 et l’IEC 60384-19.
L’objet du présent document est de prescrire des valeurs assignées et des caractéristiques préférentielles et de choisir à partir de l’IEC 60384-1 les procédures d’assurance de la qualité, les essais et les méthodes de mesure appropriées, et de donner les exigences de performance générales pour ce type de condensateur. Les sévérités d’essai et les exigences prescrites dans les spécifications particulières faisant référence à la présente spécification intermédiaire sont d’un niveau supérieur ou égal à celui de la présente spécification intermédiaire, car des niveaux de performance supérieurs ne sont pas autorisés.
Cette édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente:
a) révision de toutes les parties du document en s’appuyant sur les directives ISO/IEC, Partie 2:2018, et harmonisation avec d’autres types de documents similaires;
b) organisation de la structure du document afin de suivre la nouvelle structure de spécification intermédiaire décidée par le TC 40;
c) révision des tableaux et de l’Article 5 pour éviter les répétitions et les contradictions.

Fiksni kondenzatorji za uporabo v elektronski opremi - 2. del: Področna specifikacija - Nespremenljivi kondenzatorji z dielektrikom iz metalizirane polipropilen-tereftalatne folije za enosmerne napetosti (IEC 60384-2:2021)

General Information

Status
Published
Publication Date
14-Jun-2021
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
04-Jun-2021
Due Date
09-Aug-2021
Completion Date
15-Jun-2021

Relations

Buy Standard

Standard
EN IEC 60384-2:2021
English language
35 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 60384-2:2021
01-julij-2021
Nadomešča:
SIST EN 60384-2:2012
Fiksni kondenzatorji za uporabo v elektronski opremi - 2. del: Področna
specifikacija - Nespremenljivi kondenzatorji z dielektrikom iz metalizirane
polipropilen-tereftalatne folije za enosmerne napetosti (IEC 60384-2:2021)
Fixed capacitors for use in electronic equipment - Part 2: Sectional specification - Fixed
metallized polyethylene-terephthalate film dielectric DC capacitors (IEC 60384-2:2021)
Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 2:
Rahmenspezifikation - Festkondensatoren mit metallisierter Kunststofffolie aus
Polyethylen-Terephthalat für Gleichspannung (IEC 60384-2:2021)
Condensateurs fixes utilisés dans les équipements électroniques - Partie 2: Spécification
intermédiaire - Condensateurs fixes pour courant continu à diélectrique en film de
téréphtalate de polyéthylène métallisé (IEC 60384-2:2021)
Ta slovenski standard je istoveten z: EN IEC 60384-2:2021
ICS:
31.060.10 Fiksni kondenzatorji Fixed capacitors
SIST EN IEC 60384-2:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60384-2:2021

---------------------- Page: 2 ----------------------
SIST EN IEC 60384-2:2021


EUROPEAN STANDARD EN IEC 60384-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2021
ICS 31.060.30 Supersedes EN 60384-2:2012 and all of its amendments
and corrigenda (if any)
English Version
Fixed capacitors for use in electronic equipment - Part 2:
Sectional specification - Fixed metallized polyethylene-
terephthalate film dielectric DC capacitors
(IEC 60384-2:2021)
Condensateurs fixes utilisés dans les équipements Festkondensatoren zur Verwendung in Geräten der
électroniques - Partie 2: Spécification intermédiaire - Elektronik - Teil 2: Rahmenspezifikation -
Condensateurs fixes pour courant continu à diélectrique en Festkondensatoren mit metallisierter Kunststofffolie aus
film de téréphtalate de polyéthylène métallisé Polyethylen-Terephthalat für Gleichspannung
(IEC 60384-2:2021) (IEC 60384-2:2021)
This European Standard was approved by CENELEC on 2021-05-17. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60384-2:2021 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60384-2:2021
EN IEC 60384-2:2021 (E)
European foreword
The text of document 40/2821/FDIS, future edition 5 of IEC 60384-2, prepared by IEC/TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 60384-2:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-02-17
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-05-17
document have to be withdrawn
This document supersedes EN 60384-2:2012 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60384-2:2021 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60384-14 NOTE Harmonized as EN 60384-14
IEC 60384-19 NOTE Harmonized as EN 60384-19
2

---------------------- Page: 4 ----------------------
SIST EN IEC 60384-2:2021
EN IEC 60384-2:2021 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60063 2015 Preferred number series for resistors and EN 60063 2015
capacitors
IEC 60068-1 2013 Environmental testing - Part 1: General and EN 60068-1 2014
guidance
IEC 60384-1 2016 Fixed capacitors for use in electronic EN 60384-1 2016
equipment - Part 1: Generic specification
IEC 61193-2 2007 Quality assessment systems - Part 2: EN 61193-2 2007
Selection and use of sampling plans for
inspection of electronic components and
packages
ISO 3 1973 Preferred numbers - Series of preferred - -
numbers

3

---------------------- Page: 5 ----------------------
SIST EN IEC 60384-2:2021

---------------------- Page: 6 ----------------------
SIST EN IEC 60384-2:2021



IEC 60384-2

®


Edition 5.0 2021-04




INTERNATIONAL



STANDARD



















Fixed capacitors for use in electronic equipment –

Part 2: Sectional specification – Fixed metallized polyethylene-terephthalate film

dielectric DC capacitors:

























INTERNATIONAL

ELECTROTECHNICAL


COMMISSION





ICS 31.060.30 ISBN 978-2-8322-9654-7




  Warning! Make sure that you obtained this publication from an authorized distributor.


® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 7 ----------------------
SIST EN IEC 60384-2:2021
– 2 – IEC 60384-2:2021 © IEC 2021
CONTENTS
FOREWORD . 5
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Preferred ratings and characteristics . 8
4.1 Preferred characteristics . 8
4.2 Preferred values of ratings . 8
4.2.1 Nominal capacitance (C ) . 8
N
4.2.2 Tolerance on nominal capacitance . 8
4.2.3 Rated voltage (U ) . 9
R
4.2.4 Category voltage (U ) . 9
C
4.2.5 Rated temperature . 9
5 Test and measurement procedures, and performance requirements . 9
5.1 Visual examination and check of dimensions . 9
5.2 Electrical tests . 9
5.2.1 Voltage proof . 9
5.2.2 Capacitance . 10
5.2.3 Tangent of loss angle (tan δ) . 10
5.2.4 Insulation resistance . 11
5.3 Robustness of terminations . 12
5.3.1 General . 12
5.3.2 Initial inspections . 12
5.3.3 Test method . 13
5.3.4 Final inspections and requirements . 13
5.4 Resistance to soldering heat . 13
5.4.1 General . 13
5.4.2 Test conditions . 13
5.4.3 Final inspections and requirements . 13
5.5 Solderability . 13
5.5.1 General . 13
5.5.2 Test conditions . 13
5.5.3 Final requirements . 14
5.6 Rapid change of the temperature . 14
5.6.1 General . 14
5.6.2 Initial inspections . 14
5.6.3 Test conditions . 14
5.6.4 Final inspections . 14
5.7 Vibration . 14
5.7.1 General . 14
5.7.2 Test conditions . 14
5.7.3 Final inspections and requirements . 14
5.8 Bump (repetitive shock) . 14
5.8.1 General . 14
5.8.2 Initial inspections . 14
5.8.3 Test conditions . 15

---------------------- Page: 8 ----------------------
SIST EN IEC 60384-2:2021
IEC 60384-2:2021 © IEC 2021 – 3 –
5.8.4 Final inspections and requirements . 15
5.9 Shock . 15
5.9.1 General . 15
5.9.2 Initial inspections . 15
5.9.3 Test conditions . 15
5.9.4 Final inspections and requirements . 15
5.10 Climatic sequence. 16
5.10.1 General . 16
5.10.2 Initial inspections . 16
5.10.3 Dry heat . 16
5.10.4 Damp heat, cyclic, Test Db, first cycle . 16
5.10.5 Cold. 16
5.10.6 Low air pressure . 16
5.10.7 Damp heat, cyclic, Test Db, remaining cycles . 16
5.11 Damp heat, steady state . 17
5.11.1 General . 17
5.11.2 Initial inspections . 17
5.11.3 Test conditions . 17
5.11.4 Final inspections and requirements . 17
5.12 Endurance . 17
5.12.1 General . 17
5.12.2 Initial inspections . 17
5.12.3 Test conditions . 17
5.12.4 Final inspections and requirements . 17
5.13 Charge and discharge . 18
5.13.1 General . 18
5.13.2 Initial inspections . 18
5.13.3 Test conditions . 18
5.13.4 Final inspections and requirements . 19
5.14 Component solvent resistance . 19
5.15 Solvent resistance of the marking . 19
6 Marking . 19
6.1 General . 19
6.2 Information for marking . 19
6.3 Marking of capacitors . 19
6.4 Marking of packaging . 19
6.5 Additional marking . 19
7 Information to be given in a detail specification . 20
7.1 General . 20
7.2 Outline drawing and dimensions . 20
7.3 Mounting . 20
7.4 Rating and characteristics . 20
7.4.1 General . 20
7.4.2 Particular characteristics . 20
7.4.3 Soldering . 20
7.5 Marking . 21
8 Quality assessment procedures . 21
8.1 Primary stage of manufacture . 21
8.2 Structurally similar components . 21

---------------------- Page: 9 ----------------------
SIST EN IEC 60384-2:2021
– 4 – IEC 60384-2:2021 © IEC 2021
8.3 Certified records of released lots . 21
8.4 Qualification approval procedures . 21
8.4.1 General . 21
8.4.2 Qualification approval on the basis of the fixed sample size procedures . 21
8.5 Quality conformance inspection . 28
8.5.1 Formation of inspection lots . 28
8.5.2 Test schedule . 29
8.5.3 Delayed delivery . 29
8.5.4 Assessment levels . 29
Annex X (informative) Cross-references to the previous edition of this document . 31
Bibliography . 32

Table 1 – Test points and voltages . 10
Table 2 – Tangent of loss angle requirements . 11
Table 3 – Insulation resistance requirements . 12
Table 4 – Correction factors . 12
Table 5 – Preferred severities . 15
Table 6 – Test conditions . 17
Table 7 – Lead spacing and dU/dt . 18
Table 8 – Sampling plan together with numbers of permissible non-conformance for
qualification approval test . 23
Table 9 – Test schedule for qualification approval (1 of 5) . 24
Table 10 – Lot-by-lot inspection . 29
Table 11 – Periodic inspection . 30
Table X.1 – Cross-references . 31

---------------------- Page: 10 ----------------------
SIST EN IEC 60384-2:2021
IEC 60384-2:2021 © IEC 2021 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________

FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 2: Sectional specification – Fixed metallized
polyethylene-terephthalate film dielectric DC capacitors

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60384-2 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
This fifth edition cancels and replaces the fourth edition published in 2011. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) revision of all parts of the document based on the ISO/IEC Directives, Part 2:2018 and
harmonization with other similar kinds of documents;
b) the document structure has been organized to follow the new sectional specification
structure decided by TC 40;
c) revision of tables and Clause 5 so as to prevent duplications and contradictions.
The text of this International Standard is based on the following documents:

---------------------- Page: 11 ----------------------
SIST EN IEC 60384-2:2021
– 6 – IEC 60384-2:2021 © IEC 2021
FDIS Report on voting
40/2821/FDIS 40/2830/RVD

Full information on the voting for the approval of this International Standard can be found in the
report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 60384 series, published under the general title Fixed capacitors for
use in electronic equipment, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 12 ----------------------
SIST EN IEC 60384-2:2021
IEC 60384-2:2021 © IEC 2021 – 7 –
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 2: Sectional specification – Fixed metallized
polyethylene-terephthalate film dielectric DC capacitors



1 Scope
This part of IEC 60384 applies to fixed capacitors for direct current, with metallized electrodes
and polyethylene-terephthalate dielectric for use in electronic equipment.
These capacitors have a possibility of "self-healing properties" depending on conditions of use.
They are primarily intended for applications where the AC component is small with respect to
the rated voltage. Two performance grades of capacitors are covered: grade 1 for long-life
application and grade 2 for general application.
Capacitors for electromagnetic interference suppression and surface mount fixed metallized
polyethylene-terephthalate film dielectric DC capacitors are not included, but are covered by
IEC 60384-14 and IEC 60384-19, respectively.
The object of this document is to prescribe preferred ratings and characteristics and to select
from IEC 60384-1 the appropriate quality assessment procedures, tests and measuring
methods, and to give general performance requirements for this type of capacitor. Test
severities and requirements prescribed in detail specifications referring to this sectional
specification are of equal or higher performance level, because lower performance levels are
not permitted.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60063:2015, Preferred number series for resistors and capacitors
IEC 60068-1:2013, Environmental testing – Part 1: General and guidance
IEC 60384-1:2016, Fixed capacitors for use in electronic equipment – Part 1: Generic
specification
IEC 61193-2:2007, Quality assessment systems – Part 2: Selection and use of sampling plans
for inspection of electronic components and packages
ISO 3:1973, Preferred numbers – Series of preferred numbers
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60384-1:2016 and
the following apply.

---------------------- Page: 13 ----------------------
SIST EN IEC 60384-2:2021
– 8 – IEC 60384-2:2021 © IEC 2021
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
grade 1 capacitors
capacitors intended for long-li
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.