SIST EN 2600:2019

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Bezeichnung von metallischen Halbzeugen - RegelnSérie aérospatiale - Désignation des demi-produits métalliques - RèglesAerospace series - Designation of metallic semi-finished products - Rules49.025.05Železove zlitine na splošnoFerrous alloys in generalICS:Ta slovenski standard je istoveten z:EN 2600:2018SIST EN 2600:2019en,fr,de01-marec-2019SIST EN 2600:2019SLOVENSKI
STANDARD



SIST EN 2600:2019



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2600
December
t r s z ICS
English Version
Aerospace series æ Designation of metallic semiæfinished products æ Rules Série aérospatiale æ Désignation des demiæproduits métalliques æ Règles
Luftæ und Raumfahrt æ Bezeichnung von metallischen Halbzeugen æ Regeln This European Standard was approved by CEN on
s y September
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
t x r rã t r s z ESIST EN 2600:2019



EN 2600:2018 (E) 2 Contents
Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Designation scheme . 4 Annex A (normative)
Codes for metallic semi-finished product standards . 7 Annex B (normative)
Codes for thickness, diameter, across-flats, width, length . 8 Annex C (normative)
Codes for cross-section dimensions of sections . 12 C.1 Beaded L-section, extruded . 12 C.2 L-section, extruded . 13 C.3 Chanel section, extruded . 14 C.4 T-section, extruded . 15 C.5 L-section, folded profiles . 16 C.6 L-section, folded profiles with internally lipped flanges . 17 C.7 U-section, folded profiles . 18 C.8 U-section, folded profiles with externally lipped flanges . 19 C.9 U-section, folded profiles with internally lipped flanges . 20 C.10 Z-section, folded profiles . 21 C.11 Z-section, folded profiles with one lipped flange . 22 C.12 Z-section, folded profiles with lipped flanges . 23 C.13 Top-hat section, folded profiles . 24 C.14 Bowler-hat section, folded profiles . 25 C.15 Top-hat section, folded profiles with lipped flanges . 26 Annex D (normative)
Identity block examples . 27
SIST EN 2600:2019



EN 2600:2018 (E) 3 European foreword This document (EN 2600:2018) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2019, and conflicting national standards shall be withdrawn at the latest by June 2019. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 2600:2019



EN 2600:2018 (E) 4 1 Scope This document specifies the designation rules for metallic semi-finished products given in Table 1, used in aerospace construction. It is applicable only if referred to in the metallic semi-finished product standard. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 2032-2, Aerospace series — Metallic materials — Part 2: Coding of metallurgical condition in delivery condition 3 Designation scheme The designation of a metallic semi-finished product is made up according to the directives in force. Among those directives concerning the description block, the originator code and the identity block, only the latter requires additional data. This data concerns the two components of the identity block: the “European standard block” and the “Particular product block”. Examples of the identity block are given in Annex D. 3.1 European standard block The European standard block consists of the material standard number. 3.2 Particular product block This particular product block consists, in sequence, of the following: 3.2.1 The delivery heat treatment condition code of the semi-finished product This alphabetical code (one character) defined in EN 2032-2 is called-up in the material standards. 3.2.2 The semi-finished product standard code This numerical code (two characters) is called-up in:  Annex A;  each semi-finished product standard;  the corresponding material standards. 3.2.3 Data concerning dimensions Depending on the use of the identity block, this data is either partial (method A) or complete (method B). SIST EN 2600:2019



EN 2600:2018 (E) 5 3.2.3.1 Method A Only those dimensions distinguishing the cross-section of the semi-finished product are indicated as per Table 1. These instructions concern:  the expression used (millimetres or codes).
Millimetres are systematically to be preceded by a hyphen (–).  the sequence of the codes for cross-sections, requiring more than one dimension, shall be indicated. Table 1 Semi-finished products Dimensions Thickness Diameter Across-flats Width Cross-section Sheet mm — — — — Plate Strip Foil Round bar — mm — — — Wire Square bar mm — — — — Hexagonal bar — — mm — — Rectangular bar 1 code* — 2 code* — — Round tube 2 code* 2 code* — — — Section — — — — code** * See Annex B. ** See Annex C.
3.2.3.2 Method B All dimensions of a semi-finished product are given in codes according to the sequence of Table 2.
SIST EN 2600:2019



EN 2600:2018 (E) 6 Table 2 Semi-finished products Dimensions Thickness* Diameter* Across-flats* Width* Cross-section* Length** Sheet 1 — — 2 — 3 Plate Strip Foil Round bar — 1 — — — 2 Wire Square bar 1 — — — — 2 Hexagonal bar — — 1 — — 2 Rectangular bar 1 — — 2 — 3 Round tube 2 1 — — — 3 Section — — — — 1 2 * See Annex B. ** See Annex C. SIST EN 2600:2019



EN 2600:2018 (E) 7 Annex A (normative)
Codes for metallic semi-finished product standards Table A.1 — European standards and related codes Semi-finished products Codes Semi-finished products Codes Semi-finished products Codes EN 2033 01 EN 2338 34 — 67 EN 2034 02 EN 2339 35 — 68 EN 2035 03 EN 2340 36 — 69 EN 2036 04 EN 2341 37 — 70 EN 2037 05 EN 2366 38 — 71 EN 2038 06 EN 2368 39 — 72 EN 2039 07 EN 2369 40 — 73 EN 2040 08 EN 2589 41 — 74 EN 2041 09 EN 2590 42 — 75 EN 2042 10 EN 2599 43 — 76 EN 2044 11 EN 2615 44 — 77 EN 2045 12 EN 2616 45 — 78 EN 2046 13 EN 2617 46 — 79 EN 2047 14 EN 2621 47 — 80 EN 2048 15 EN 2622 48 — 81 EN 2049 16 EN 3145 49 — 82 EN 2050 17 EN 3146 50 — 83 EN 2051 18 — 51 — 84 EN 2052 19 — 52 — 85 EN 2053 20 — 53 — 86 EN 2054 21 — 54 — 87 EN 2055 22 — 55 — 88 EN 2056 23 — 56 — 89 EN 2057 24 — 57 — 90 EN 2058 25 — 58 — 91 EN 2059 26 — 59 — 92 EN 2060 27 — 62 — 93 EN 2061 28 — 61 — 94 EN 2071 29 — 62 — 95 EN 2131 30 — 63 — 96 EN 2134 31 — 64 — 97 EN 2257 32 — 65 — 98 EN 2258 33 — 66 — 99 SIST EN 2600:2019



EN 2600:2018 (E) 8 Annex B (normative)
Codes for thickness, diameter, across-flats, width, length Table B.1 — Dimensions and related codes (1 of 4) Dimensions in millimetres Dimensions Codes Dimensions Codes Dimensions Codes Dimensions Codes 0,1 AA 5,4 CH 17 EQ 70 GY 0,2 AB 5,5 CJ 18 ER 71 GZ 0,3 AC 5,6 CK 19 ES 72 HA 0,4 AD 5,7 CL 20 ET 73 HB 0,5 AE 5,8 CM 21 EU 74 HC 0,6 AF 5,9 CN 22 EV 75 HD 0,7 AG 6,0 CP 23 EW 76 HE 0,8 AH 6,1 CQ 24 EY 77 HF 0,9 AJ 6,2 CR 25 EZ 78 HG 1,0 AK 6,3 CS 26 FA 79 HH 1,1 AL 6,4 CT 27 FB 80 HJ 1,2 AM 6,5 CU 28 FC 81 HK 1,3 AN 6,6 CV 29 FD 82 HL 1,4 AP 6,7 CW 30 FE 83 HM 1,5 AQ 6,8 CY 31 FF 84 HN 1,6 AR 6,9 CZ 32 FG 85 HP 1,7 AS 7,0 DA 33 FH 86 HQ 1,8 AT 7,1 DB 34 FJ 87 HR 1,9 AU 7,2 DC 35 FK 88 HS 2,0 AV 7,3 DD 36 FL 89 HT 2,1 AW 7,4 DE 37 FM 90 HU 2,2 AY 7,5 DF 38 FN 91 HV 2,3 AZ 7,6 DG 39 FP 92 HW 2,4 BA 7,7 DH 40 FQ 93 HY 2,5 BB 7,8 DJ 41 FR 94 HZ
SIST EN 2600:2019



EN 2600:2018 (E) 9 Table B.1 — Dimensions and related codes (2 of 4) Dimensions in millimetres Dimensions Codes Dimensions Codes Dimensions Codes Dimensions Codes 2,6 BC 7,9 DK 42 FS 95 JA 2,7 BD 8,0 DL 43 FT 96 JB 2,8 BE 8,1 DM 44 FU 97 JC 2,9 BF 8,2 DN 45 FV 98 JD 3,0 BG 8,3 DP 46 FW 99 JE 3,1 BH 8,4 DQ 47 FY 100 JF 3,2 BJ 8,5 DR 48 F
...