SIST EN 61784-5-2:2014

SLOVENSKI STANDARD
SIST EN 61784-5-2:2014
01-april-2014
1DGRPHãþD
SIST EN 61784-5-2:2012
Industrijska komunikacijska omrežja - Profili - 5-2. del: Inštalacija procesnih vodil -
Inštalacijski profili za CPF 2 (IEC 61784-5-2:2013)
Industrial communication networks - Profiles -- Part 5-2: Installation of fieldbuses -
Installation profiles for CPF 2
Industrielle Kommunikationsnetze - Profile -- Teil 5-2: Feldbusinstallation -
Installationsprofile für die Kommunikationsprofilfamilie 2
Réseaux de communication industriels - Profils -- Partie 5-2: Installation des bus de
terrain - Profils d'installation pour CPF 2
Ta slovenski standard je istoveten z: EN 61784-5-2:2013
ICS:
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
35.100.40 Transportni sloj Transport layer
SIST EN 61784-5-2:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61784-5-2:2014

---------------------- Page: 2 ----------------------

SIST EN 61784-5-2:2014

EUROPEAN STANDARD
EN 61784-5-2

NORME EUROPÉENNE
December 2013
EUROPÄISCHE NORM

ICS 25.040.40; 35.100.40 Supersedes EN 61784-5-2:2012


English version


Industrial communication networks -
Profiles -
Part 5-2: Installation of fieldbuses -
Installation profiles for CPF 2
(IEC 61784-5-2:2013)


Réseaux de communication industriels -  Industrielle Kommunikationsnetze -
Profils - Profile -
Partie 5-2: Installation des bus de terrain - Teil 5-2: Feldbusinstallation -
Profils d'installation pour CPF 2 Installationsprofile für die
(CEI 61784-5-2:2013) Kommunikationsprofilfamilie 2
(IEC 61784-5-2:2013)



This European Standard was approved by CENELEC on 2013-10-14. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61784-5-2:2013 E

---------------------- Page: 3 ----------------------

SIST EN 61784-5-2:2014
EN 61784-5-2:2013 - 2 -
Foreword
The text of document 65C/738/FDIS, future edition 3 of IEC 61784-5-2, prepared by
SC 65C "Industrial networks" of IEC/TC 65 "Industrial-process measurement, control and automation"
was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61784-5-2:2013.

The following dates are fixed:
(dop) 2014-07-14
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2016-10-14
standards conflicting with the
document have to be withdrawn

This document supersedes EN 61784-5-2:2012.

EN 61784-5-2:2013 includes the following significant technical changes with respect to
EN 61784-5-2:2012:
– updates pertaining to current installation practices;
– addition of new technology that has become recently available;
– errors have been corrected;
– improved alignment with EN 61918.

This standard is to be used in conjunction with EN 61918:2013.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice
The text of the International Standard IEC 61784-5-2:2013 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 61158 Series NOTE Harmonized as EN 61158 Series (not modified).
IEC/TR 61158-1 NOTE Harmonized as CLC/TR 61158-1.
IEC 62026-3 NOTE Harmonized as EN 62026-3.

---------------------- Page: 4 ----------------------

SIST EN 61784-5-2:2014
- 3 - EN 61784-5-2:2013
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Annex ZA of EN 61918:2013 applies, except as follows:

Publication Year Title EN/HD Year
Addition to Annex ZA of EN 61918:2013:
IEC 61918 2013 Industrial communication networks - EN 61918 2013
Installation of communication networks in
industrial premises

---------------------- Page: 5 ----------------------

SIST EN 61784-5-2:2014

---------------------- Page: 6 ----------------------

SIST EN 61784-5-2:2014




IEC 61784-5-2

®


Edition 3.0 2013-09




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside










Industrial communication networks – Profiles –

Part 5-2: Installation of fieldbuses – Installation profiles for CPF 2




Réseaux de communication industriels – Profils –

Partie 5-2: Installation des bus de terrain – Profils d'installation pour CPF 2
















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX XH


ICS 25.040.40; 35.100.40 ISBN 978-2-8322-1060-4



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61784-5-2:2014
– 2 – 61784-5-2 © IEC:2013
CONTENTS
FOREWORD . 9
INTRODUCTION . 11
1 Scope . 12
2 Normative references . 12
3 Terms, definitions and abbreviated terms . 12
4 CPF 2: Overview of installation profiles . 12
5 Installation profile conventions . 13
6 Conformance to installation profiles . 14
Annex A (normative) CP 2/1 (ControlNet™) specific installation profile . 15
A.1 Installation profile scope . 15
A.2 Normative references . 15
A.3 Installation profile terms, definitions, and abbreviated terms . 15
A.3.1 Terms and definitions . 15
A.3.2 Abbreviated terms . 15
A.3.3 Conventions for installation profiles . 15
A.4 Installation planning . 16
A.4.1 General . 16
A.4.2 Planning requirements . 17
A.4.3 Network capabilities . 18
A.4.4 Selection and use of cabling components . 24
A.4.5 Cabling planning documentation . 41
A.4.6 Verification of planning specification . 41
A.5 Installation implementation . 41
A.5.1 General requirements . 41
A.5.2 Cable installation . 41
A.5.3 Connector installation . 43
A.5.4 Terminator installation . 53
A.5.5 Device installation . 53
A.5.6 Coding and labelling . 55
A.5.7 Earthing and bonding of equipment and devices and shield cabling . 56
A.5.8 As-implemented cabling documentation . 57
A.6 Installation verification and installation acceptance test . 57
A.6.1 General . 57
A.6.2 Installation verification . 57
A.6.3 Installation acceptance test . 60
A.7 Installation administration . 62
A.8 Installation maintenance and installation troubleshooting . 62
A.8.1 General . 62
A.8.2 Maintenance . 62
A.8.3 Troubleshooting . 62
A.8.4 Specific requirements for maintenance and troubleshooting . 67
Annex B (normative) CP 2/2 (EtherNet/IP™) specific installation profile . 68
B.1 Installation profile scope . 68
B.2 Normative references . 68

---------------------- Page: 8 ----------------------

SIST EN 61784-5-2:2014
61784-5-2 © IEC:2013 – 3 –
B.3 Installation profile terms, definitions, and abbreviated terms . 68
B.3.1 Terms and definitions . 68
B.3.2 Abbreviated terms . 68
B.3.3 Conventions for installation profiles . 68
B.4 Installation planning . 69
B.4.1 General . 69
B.4.2 Planning requirements . 70
B.4.3 Network capabilities . 70
B.4.4 Selection and use of cabling components . 74
B.4.5 Cabling planning documentation . 86
B.4.6 Verification of cabling planning specification . 87
B.5 Installation implementation . 87
B.5.1 General requirements . 87
B.5.2 Cable installation . 87
B.5.3 Connector installation . 88
B.5.4 Terminator installation . 89
B.5.5 Device installation . 89
B.5.6 Coding and labelling . 89
B.5.7 Earthing and bonding of equipment and devices and shield cabling . 89
B.5.8 As-implemented cabling documentation . 91
B.6 Installation verification and installation acceptance test . 91
B.6.1 General . 91
B.6.2 Installation verification . 91
B.6.3 Installation acceptance test . 93
B.7 Installation administration . 94
B.8 Installation maintenance and installation troubleshooting . 94
Annex C (normative) CP 2/3 (DeviceNet™) specific installation profile . 95
C.1 Installation profile scope . 95
C.2 Normative references . 95
C.3 Installation profile terms, definitions, and abbreviated terms . 95
C.3.1 Terms and definitions . 95
C.3.2 Abbreviated terms . 95
C.3.3 Conventions for installation profiles . 95
C.4 Installation planning . 96
C.4.1 General . 96
C.4.2 Planning requirements . 97
C.4.3 Network capabilities . 98
C.4.4 Selection and use of cabling components . 112
C.4.5 Cabling planning documentation . 121
C.4.6 Verification of cabling planning specification . 121
C.5 Installation implementation . 121
C.5.1 General requirements . 121
C.5.2 Cable installation . 121
C.5.3 Connector installation . 124
C.5.4 Terminator installation . 136
C.5.5 Device installation . 138
C.5.6 Coding and labelling . 141

---------------------- Page: 9 ----------------------

SIST EN 61784-5-2:2014
– 4 – 61784-5-2 © IEC:2013
C.5.7 Earthing and bonding of equipment and devices and shield cabling . 141
C.5.8 As-implemented cabling documentation . 142
C.6 Installation verification and installation acceptance test . 142
C.6.1 General . 142
C.6.2 Installation verification . 142
C.6.3 Installation acceptance test . 145
C.7 Installation administration . 146
C.8 Installation maintenance and installation troubleshooting . 146
C.8.1 General . 146
C.8.2 Maintenance . 146
C.8.3 Troubleshooting . 146
C.8.4 Specific requirements for maintenance and troubleshooting . 146
Annex D (informative) Additional information . 150
D.1 Network validation check sheet for CP 2/3 (DeviceNet) . 150
Bibliography . 154

Figure 1 – Standards relationships . 11
Figure A.1 – Interconnection of CPF 2 networks . 16
Figure A.2 – Overview of CPF 2/1 networks . 17
Figure A.3 – Drop cable requirements . 19
Figure A.4 – Placement of BNC/TNC plugs . 19
Figure A.5 – Placement of terminators . 20
Figure A.6 – Extending a network using repeaters . 20
Figure A.7 – Extending a network using active star topology . 21
Figure A.8 – Links . 21
Figure A.9 – Extending the network beyond 99 nodes . 22
Figure A.10 – Maximum allowable taps per segment . 30
Figure A.11 – Example of repeaters in star configuration . 31
Figure A.12 – Repeaters in parallel . 32
Figure A.13 – Repeaters in combination series and parallel . 33
Figure A.14 – Ring repeater . 33
Figure A.15 – Installing bulkheads . 34
Figure A.16 – Coaxial BNC and TNC terminators . 35
Figure A.17 – Terminator placement in a segment . 35
Figure A.18 – Redundant network icons . 37
Figure A.19 – Redundant coax media . 38
Figure A.20 – Redundant fibre media . 38
Figure A.21 – Repeaters in series versus length difference for coax media . 39
Figure A.22 – Repeaters in series versus length difference for fibre media . 39
Figure A.23 – Example of redundant coax network with repeaters . 40
Figure A.24 – Example of improper redundant node connection . 40
Figure A.25 – Example tool kit for installing BNC connectors . 44
Figure A.26 – Calibration of coaxial stripper . 45
Figure A.27 – Coax PVC strip length detail (informative) . 45

---------------------- Page: 10 ----------------------

SIST EN 61784-5-2:2014
61784-5-2 © IEC:2013 – 5 –
Figure A.28 – Memory cartridge and blade . 46
Figure A.29 – Cable position . 47
Figure A.30 – Locking the cable . 47
Figure A.31 – Stripping the cable . 47
Figure A.32 – Install the crimp ferrule . 48
Figure A.33 – Cable preparation for PVC type cables (informative) . 48
Figure A.34 – Cable preparation for FEP type cables (informative) . 49
Figure A.35 – Strip guides . 49
Figure A.36 – Using the flare tool . 50
Figure A.37 – Expanding the shields . 50
Figure A.38 – Install the centre pin . 50
Figure A.39 – Crimping the centre pin . 51
Figure A.40 – Installing the connector body . 51
Figure A.41 – Installing the ferrule . 51
Figure A.42 – Crimp tool . 52
Figure A.43 – Sealed IP65/67 cable . 53
Figure A.44 – Terminator placement . 53
Figure A.45 – Mounting the taps . 54
Figure A.46 – Mounting the tap assembly using the universal mounting bracket . 55
Figure A.47 – Mounting the tap using tie wraps or screws . 55
Figure A.48 – Redundant network icons . 56
Figure A.49 – Network test tool . 58
Figure A.50 – Shorting the cable to test for continuity . 59
Figure A.51 – Testing fibre segments . 61
Figure A.52 – Multi-fibre backbone cable housing . 63
Figure A.53 – Repeater adapter module . 63
Figure A.54 – Short and medium distance fibre module LEDs . 65
Figure A.55 – Long and extra long repeater module LEDs . 66
Figure B.1 – Interconnection of CPF 2 networks . 69
Figure B.2 – Redundant linear bus . 71
Figure B.3 – Peer to peer connections . 71
Figure B.4 – Mated connections . 74
Figure B.5 – The 8-way modular sealed jack & plug (plastic housing) . 78
Figure B.6 – The 8-way modular sealed jack & plug (metal housing) . 79
Figure B.7 – M12-4 connectors . 79
Figure B.8 – Simplex LC connector . 80
Figure B.9 – Duplex LC connector . 80
Figure B.10 – IP65/67 sealed duplex LC connector . 81
Figure B.11 – IP65/67 sealed duplex SC-RJ connector . 81
Figure B.12 – M12-4 to 8-way modular bulkhead . 83
Figure B.13 – The 8-way modular sealed jack & plug (plastic housing) . 88
Figure B.14 – The 8-way modular sealed jack & plug (metal housing) . 89
Figure B.15 – M12-4 connectors . 89

---------------------- Page: 11 ----------------------

SIST EN 61784-5-2:2014
– 6 – 61784-5-2 © IEC:2013
Figure B.16 – Earthing of cable shield . 91
Figure C.1 – Interconnection of CPF 2 networks . 96
Figure C.2 – Connection to generic cabling . 97
Figure C.3 – DeviceNet cable system uses a trunk/drop line topology . 98
Figure C.4 – Measuring the trunk length .
...