SIST EN ISO 2009:2011

SLOVENSKI STANDARD
SIST EN ISO 2009:2011
01-december-2011
1DGRPHãþD
SIST EN ISO 2009:1996
Vijaki z zarezano ugrezno glavo - Razred izdelave A (ISO 2009:2011)
Slotted countersunk flat head screws - Product grade A (ISO 2009:2011)
Senkschrauben mit Schlitz (Einheitskopf) - Produktklasse A (ISO 2009:2011)
Vis à métaux à tête fraisée fendue - Grade A (ISO 2009:2011)
Ta slovenski standard je istoveten z: EN ISO 2009:2011
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN ISO 2009:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 2009:2011

---------------------- Page: 2 ----------------------

SIST EN ISO 2009:2011


EUROPEAN STANDARD
EN ISO 2009

NORME EUROPÉENNE

EUROPÄISCHE NORM
September 2011
ICS 21.060.10 Supersedes EN ISO 2009:1994
English Version
Slotted countersunk flat head screws - Product grade A (ISO
2009:2011)
Vis à métaux à tête fraisée fendue - Grade A (ISO Senkschrauben mit Schlitz - Produktklasse A (ISO
2009:2011) 2009:2011)
This European Standard was approved by CEN on 8 August 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2009:2011: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 2009:2011
EN ISO 2009:2011 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 2009:2011
EN ISO 2009:2011 (E)
Foreword
This document (EN ISO 2009:2011) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2012, and conflicting national standards shall be withdrawn at
the latest by March 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 2009:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 2009:2011 has been approved by CEN as a EN ISO 2009:2011 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 2009:2011

---------------------- Page: 6 ----------------------

SIST EN ISO 2009:2011

INTERNATIONAL ISO
STANDARD 2009
Fourth edition
2011-09-01


Slotted countersunk flat head screws —
Product grade A
Vis à métaux à tête fraisée fendue — Grade A




Reference number
ISO 2009:2011(E)
©
ISO 2011

---------------------- Page: 7 ----------------------

SIST EN ISO 2009:2011
ISO 2009:2011(E)

COPYRIGHT PROTECTED DOCUMENT


©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2011 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 2009:2011
ISO 2009:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 2009 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 11, Fasteners with
metric external thread.
This fourth edition cancels and replaces the third edition (ISO 2009:1994), of which it constitutes a minor
revision.

© ISO 2011 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 2009:2011

---------------------- Page: 10 ----------------------

SIS
...