Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)

Specifies a general test method for  determination of the resistance to internal  hydrostatic pressure at a given temperature  of thermoplastics pipes, fittings and piping  systems for the transport of fluids. The  preparation of test pieces to be used is  described in the appropriate parts 2, 3 or 4  of this international standard.

Rohre, Formstücke und Bauteilkombinationen aus thermoplastischen Kunststoffen für den Transport von Flüssigkeiten - Bestimmung der Widerstandsfähigkeit gegen inneren Überdruck - Teil 1: Allgemeines Prüfverfahren (ISO 1167-1:2006)

Dieser Teil der ISO 1167 legt ein allgemeines Prüfverfahren zur Bestimmung der Widerstandsfähigkeit gegen hydrostatischen Innendruck von Rohren, Formstücken und Rohrleitungssystemen aus Thermoplasten für den Transport von Flüssigkeiten bei einer festgelegten Temperatur fest.
Das Verfahren beinhaltet Prüfungen Wasser-in-Wasser, Wasser-in-Luft und Wasser-in-Flüssigkeit.

Tubes, raccords et assemblages en matieres thermoplastiques pour le transport des fluides - Détermination de la résistance a la pression interne - Partie 1: Méthode générale (ISO 1167-1:2006)

L'ISO 1167-1:2006 spécifie une méthode générale d'essai pour la détermination de la résistance à une pression hydrostatique interne, à une température donnée, des tubes, raccords et systèmes de canalisations en matières thermoplastiques destinés au transport de fluides. La méthode est adaptée pour des essais «eau-dans-eau», «eau-dans-air» et «eau-dans-liquide».

Plastomerne cevi, fitingi in spoji za pretok tekočin in plinov – Ugotavljanje odpornosti proti notranjemu tlaku – 1. del: Osnovna metoda (ISO 1167-1:2006)

General Information

Status
Published
Publication Date
31-Mar-2006
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Apr-2006
Due Date
01-Apr-2006
Completion Date
01-Apr-2006

Relations

Buy Standard

Standard
EN ISO 1167-1:2006
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 1167-1:2006
01-april-2006
1DGRPHãþD
SIST EN 921:1997
3ODVWRPHUQHFHYLILWLQJLLQVSRML]DSUHWRNWHNRþLQLQSOLQRY±8JRWDYOMDQMH
RGSRUQRVWLSURWLQRWUDQMHPXWODNX±GHO2VQRYQDPHWRGD ,62
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids -
Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-
1:2006)
Rohre, Formstücke und Bauteilkombinationen aus thermoplastischen Kunststoffen für
den Transport von Flüssigkeiten - Bestimmung der Widerstandsfähigkeit gegen inneren
Überdruck - Teil 1: Allgemeines Prüfverfahren (ISO 1167-1:2006)
Tubes, raccords et assemblages en matieres thermoplastiques pour le transport des
fluides - Détermination de la résistance a la pression interne - Partie 1: Méthode
générale (ISO 1167-1:2006)
Ta slovenski standard je istoveten z: EN ISO 1167-1:2006
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
SIST EN ISO 1167-1:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 1167-1:2006

---------------------- Page: 2 ----------------------

SIST EN ISO 1167-1:2006
EUROPEAN STANDARD
EN ISO 1167-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2006
ICS 23.040.45; 23.040.20 Supersedes EN 921:1994
English Version
Thermoplastics pipes, fittings and assemblies for the
conveyance of fluids - Determination of the resistance to internal
pressure - Part 1: General method (ISO 1167-1:2006)
Tubes, raccords et assemblages en matières Rohre, Formstücke und Zubehör aus thermoplastischen
thermoplastiques pour le transport des fluides - Kunststoffen für den Transport von Flüssigkeiten -
Détermination de la résistance à la pression interne - Partie Bestimmung der Widerstandsfähigkeit gegen inneren
1: Méthode générale (ISO 1167-1:2006) Überdruck - Teil 1: Allgemeines Prüfverfahren (ISO 1167-
1:2006)
This European Standard was approved by CEN on 23 January 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1167-1:2006: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 1167-1:2006

EN ISO 1167-1:2006 (E)





Foreword


This document (EN ISO 1167-1:2006) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical
Committee CEN/TC 155 "Plastics piping systems and ducting systems", the secretariat of which
is held by NEN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by August 2006, and conflicting national
standards shall be withdrawn at the latest by August 2006.

This document supersedes EN 921:1994.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 1167-1:2006 has been approved by CEN as EN ISO 1167-1:2006 without any
modifications.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 1167-1:2006


INTERNATIONAL ISO
STANDARD 1167-1
First edition
2006-02-01


Thermoplastics pipes, fittings and
assemblies for the conveyance of
fluids — Determination of the resistance
to internal pressure —
Part 1:
General method
Tubes, raccords et assemblages en matières thermoplastiques pour le
transport des fluides — Détermination de la résistance à la pression
interne —
Partie 1: Méthode générale





Reference number
ISO 1167-1:2006(E)
©
ISO 2006

---------------------- Page: 5 ----------------------

SIST EN ISO 1167-1:2006
ISO 1167-1:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2006 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 1167-1:2006
ISO 1167-1:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Principle. 2
5 Apparatus . 2
6 Test pieces . 4
6.1 Preparation of test pieces. 4
6.2 Number of test pieces . 4
7 Calculation of test pressure . 4
7.1 General. 4
7.2 Pressure calculations based on the measured dimensions of the test piece . 5
7.3 Pressure calculations based on the nominal dimensions of the test piece. 5
7.4 Pressure calculations based on SDR of pipe(s) of the test piece . 5
8 Calibration and accuracy of the apparatus. 6
9 Conditioning. 6
10 Test procedure . 6
11 Test report . 7

© ISO 2006 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 1167-1:2006
ISO 1167-1:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 1167-1 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the
transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and
their accessories — Test methods and basic specifications.
This first edition of ISO 1167-1, together with ISO 1167-2, cancels and replaces ISO 1167:1996 and, together
with ISO 1167-3, cancels and replaces ISO 12092:2000, of which it constitutes a technical revision.
ISO 1167 consists of the following parts, under the general title Thermoplastics pipes, fittings and assemblies
for the conveyance of fluids — Determination of the resistance to internal pressure:
⎯ Part 1: General method
⎯ Part 2: Preparation of pipe test pieces
⎯ Part 3: Preparation of components
⎯ Part 4: Preparation of assemblies
iv © ISO 2006 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 1167-1:2006
ISO 1167-1:2006(E)
Introduction
Tests for determining resistance to internal pressure are essential for assessing the properties and durability
of thermoplastics piping system parts. In fact, they constitute a basis for determining short-term and long-term
characteristics.
Many International Standards contain requirements for the determination of the resistance to pressure of
pipes, fittings or assemblies. All these documents describe the equipment for pressurizing the different test
pieces considered as well as the testing procedure and the test report.
In order to avoid unnecessary repetition, it is desirable to group together all these documents and to establish
one International Standard divided into several parts.
ISO 1167-1 contains a description of the equipment used to pressurize test pieces, the testing procedure to be
applied and the test report.
ISO 1167-2, ISO 1167-3 and ISO 1167-4 describe the method of preparation of test pieces corresponding to
each case considered: pipes, components or assemblies.

© ISO 2006 – All rights reserved v

---------------------- Page: 9 ----------------------

SIST EN ISO 1167-1:2006

---------------------- Page: 10 ----------------------

SIST EN ISO 1167-1:2006
INTERNATIONAL STANDARD ISO 1167-1:2006(E)

Thermoplastics pipes, fittings and assemblies for the
conveyance of fluids — Determination of the resistance
to internal pressure —
Part 1:
General method
1 Scope
This part of ISO 1167 specifies a general test method for determining the resistance to internal hydrostatic
pressure at a given temperature of thermoplastics pipes, fittings and piping systems for the transport of fluids.
The method accommodates water-in-water, water-in-air and water-in-liquid tests.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1167-2:2006, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination
of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
ISO 1167-3, Thermoplastics pipes, fittings and assemblies the conveyance of fluids — Determination of the
1)
resistance to internal pressure — Part 3: Preparation of components
ISO 1167-4, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of
1)
the resistance to internal pressure — Part 4: Preparation of assemblies
ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions
ISO 9080, Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of
thermoplastics pipe materials in pipe form by extrapolation
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
component
fitting or valve, in single or multiple form, that is supplied as an integral unit
3.2
standard dimension ratio
SDR
ratio of the nominal outside diameter d of a pipe to its nominal wall thickness e
n n

1) To be published.
© ISO 2006 – All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 1167-1:2006
ISO 1167-1:2006(E)
4 Principle
After conditioning, test pieces are subjected to a specified constant internal hydrostatic pressure for a
specified period of time or until a test piece or pieces fail.
Throughout the test, the test pieces are kept in an environment at a specified constant temperatur
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.