SIST EN ISO 16103:2005

SLOVENSKI STANDARD
SIST EN ISO 16103:2005
01-september-2005
(PEDODåD7UDQVSRUWQDHPEDODåD]DQHYDUQREODJR5HFLNOLUDQLSODVWLþQLPDWHULDOL
,62
Packaging - Transport packages for dangerous goods - Recycled plastics material (ISO
16103:2005)
Verpackung - Verpackungen zur Beförderung gefährlicher Güter - Recycling-Kunststoffe
(ISO 16103:2005)
Emballages - Emballages de transport pour marchandises dangereuses - Matériaux
plastiques recyclés (ISO 16103:2005)
Ta slovenski standard je istoveten z: EN ISO 16103:2005
ICS:
13.300 Varstvo pred nevarnimi Protection against dangerous
izdelki goods
55.040 0DWHULDOLLQSULSRPRþNL]D Packaging materials and
SDNLUDQMH accessories
SIST EN ISO 16103:2005 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 16103:2005

---------------------- Page: 2 ----------------------

SIST EN ISO 16103:2005
EUROPEAN STANDARD
EN ISO 16103
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2005
ICS 13.300; 55.020

English Version
Packaging - Transport packages for dangerous goods -
Recycled plastics material (ISO 16103:2005)
Emballages - Emballages de transport pour marchandises Verpackung - Verpackungen zur Beförderung gefährlicher
dangereuses - Matériaux plastiques recyclés (ISO Güter - Recycling-Kunststoffe (ISO 16103:2005)
16103:2005)
This European Standard was approved by CEN on 1 June 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16103:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 16103:2005

EN ISO 16103:2005 (E)





Foreword


This document (EN ISO 16103:2005) has been prepared by Technical Committee ISO/TC 122
"Packaging" in collaboration with Technical Committee CEN/TC 261 "Packaging", the secretariat
of which is held by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2006, and conflicting national
standards shall be withdrawn at the latest by January 2006.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 16103:2005 has been approved by CEN as EN ISO 16103:2005 without any
modifications.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 16103:2005


INTERNATIONAL ISO
STANDARD 16103
First edition
2005-07-01

Packaging — Transport packaging for
dangerous goods — Recycled plastics
material
Emballages — Emballages de transport pour marchandises
dangereuses — Matériaux plastiques recyclés




Reference number
ISO 16103:2005(E)
©
ISO 2005

---------------------- Page: 5 ----------------------

SIST EN ISO 16103:2005
ISO 16103:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 16103:2005
ISO 16103:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16103 was prepared by Technical Committee ISO/TC 122, Packaging, Subcommittee SC 3, Performance
requirements and tests for means of packaging, packages and unit loads (as required by ISO/TC 122).
© ISO 2005 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 16103:2005
ISO 16103:2005(E)
Introduction
The aim of this International Standard is to specify sufficiently the necessary controls for the use of recycled
plastics materials as identified in the United Nations Recommendations on the Transport of Dangerous Goods,
by selection into batches. Packagings produced from each batch of recycled plastics material undergo
mechanical testing as in design type testing.
These Recommendations are given legal entity by the provisions of a series of modal agreements for the
international transport of dangerous goods:
 the European Agreement concerning the International Carriage of Dangerous Goods by Road (ADR)
(see [1] in the Bibliography);
 the International Civil Aviation Organization's Technical Instructions for the Safe Transport of Dangerous
Goods by Air (see [2] in the Bibliography);
 the International Maritime Dangerous Goods Code (see [3] in the Bibliography);
 the Regulations concerning the International Carriage of Dangerous Goods by Rail (RID) (see [4] in the
Bibliography).
The application of this International Standard needs to take account of the requirements of these international
agreements and the relevant national regulations for domestic transport of dangerous goods.

iv © ISO 2005 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 16103:2005
INTERNATIONAL STANDARD ISO 16103:2005(E)

Packaging — Transport packaging for dangerous goods —
Recycled plastics material
1 Scope
This International Standard specifies the requirements and test methods for the production of recycled plastics
materials to be used for packagings for the transport of dangerous goods. This includes guidance on the
quality assurance programme.
NOTE The quality assurance programme for the production of packagings is described in ISO 16106 (see [5] in the
Bibliography).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 527-1, Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 1133, Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of
thermop
...