SIST EN IEC 60851-1:2021

SLOVENSKI STANDARD
SIST EN IEC 60851-1:2021
01-oktober-2021
Nadomešča:
SIST EN 60851-1:2001
SIST EN 60851-1:2001/A1:2004
SIST EN 60851-1:2001/A2:2010
Navijalne žice - Preskusne metode - 1. del: Splošno (IEC 60851-1:2021)
Winding wires - Test methods - Part 1: General (IEC 60851-1:2021)
Wickeldrähte - Prüfverfahren - Teil 1: Allgemeines (IEC 60851-1:2021)
Méthodes d'essai des fils de bobinage - Partie 1: Généralités (IEC 60851-1:2021)
Ta slovenski standard je istoveten z: EN IEC 60851-1:2021
ICS:
29.060.10 Žice Wires
SIST EN IEC 60851-1:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60851-1:2021

---------------------- Page: 2 ----------------------
SIST EN IEC 60851-1:2021


EUROPEAN STANDARD EN IEC 60851-1

NORME EUROPÉENNE

EUROPÄISCHE NORM August 2021
ICS 29.060.10 Supersedes EN 60851-1:1996 and all of its amendments
and corrigenda (if any)
English Version
Winding wires - Test methods - Part 1: General
(IEC 60851-1:2021)
Fils de bobinage - Méthodes d'essai - Partie 1: Généralités Wickeldrähte - Prüfverfahren - Teil 1: Allgemeines
(IEC 60851-1:2021) (IEC 60851-1:2021)
This European Standard was approved by CENELEC on 2021-07-21. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60851-1:2021 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60851-1:2021
EN IEC 60851-1:2021 (E)
European foreword
The text of document 55/1913/FDIS, future edition 3 of IEC 60851-1, prepared by IEC/TC 55 “Winding
wires” was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 60851-1:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022–04–21
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024–07–21
document have to be withdrawn
This document supersedes EN 60851-1:1996 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60851-1:2021 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60264 (series) NOTE Harmonized as EN 60264 (series)
IEC 60851 (series) NOTE Harmonized as EN 60851 (series)
2

---------------------- Page: 4 ----------------------
SIST EN IEC 60851-1:2021
EN IEC 60851-1:2021 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60317 series Specifications for particular types of EN 60317 series
winding wires
IEC 60851-2 2009 Winding wires - Test methods - Part 2: EN 60851-2 2009
Determination of dimensions
+ A1 2015  + A1 2015
+ A2 2019  + A2 2019
IEC 60851-3 2009 Winding wires - Test methods - Part 3: EN 60851-3 2009
Mechanical properties
+ A1 2013  + A1 2013
+ A2 2019  + A2 2019
IEC 60851-4 2016 Winding wires - Test methods - Part 4: EN 60851-4 2016
Chemical properties
IEC 60851-5 2008 Winding wires - Test methods - Part 5: EN 60851-5 2008
Electrical properties
+ A1 2011  + A1 2011
+ A2 2019  + A2 2019
IEC 60851-6 2012 Winding wires - Test methods - Part 6: EN 60851-6 2012
Thermal properties

3

---------------------- Page: 5 ----------------------
SIST EN IEC 60851-1:2021

---------------------- Page: 6 ----------------------
SIST EN IEC 60851-1:2021
IEC 60851-1
®

Edition 3.0 2021-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Winding wires – Test methods –
Part 1: General
Fils de bobinage – Méthodes d'essai –
Partie 1: Généralités
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8322-9882-4
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 60851-1:2021
– 2 – IEC 60851-1:2021 © IEC 2021
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and general notes on methods of test . 6
3.1 Terms and definitions . 6
3.2 General notes on methods of test . 8
Annex A (informative) Contents of IEC 60851-2 to IEC 60851-6 with indication of tests . 10
A.1 General . 10
A.2 IEC 60851-2 . 10
A.3 IEC 60851-3 . 11
A.4 IEC 60851-4 . 12
A.5 IEC 60851-5 . 13
A.6 IEC 60851-6 . 14
Bibliography . 15

---------------------- Page: 8 ----------------------
SIST EN IEC 60851-1:2021
IEC 60851-1:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

WINDING WIRES – TEST METHODS –

Part 1: General

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 60851-1 has been prepared by IEC technical committee 55: Winding wires. It is an
International Standard.
This third edition cancels and replaces the second edition published in 1996, and its
amendment 1:2003 and amendment 2:2009. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) revision to Clause 2 to update the list of normative references;
b) revision to 3.2 atmospheric conditions for testing;
c) addition to 3.2 with remarks concerning frequency and management of tests;
d) revision to Annex A to update the contents list of IEC 60851 series of tests.

---------------------- Page: 9 ----------------------
SIST EN IEC 60851-1:2021
– 4 – IEC 60851-1:2021 © IEC 2021
The text of this International Standard is based on the following documents:
FDIS Report on voting
55/1913/FDIS 55/1916/RVD

Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
Annex A is for information only.
A list of all parts in the IEC 60851 series, pub
...