SIST EN 61850-10:2005

SLOVENSKI STANDARD
SIST EN 61850-10:2005
01-november-2005
Komunikacijska omrežja in sistemi v postajah – 10. del: Preskušanje skladnosti
(IEC 61850-10:2005)
Communication networks and systems in substations -- Part 10: Conformance testing
Kommunikationsnetze- und -systeme in Stationen -- Teil 10: Konformitätsprüfung
Réseaux et systèmes de communication dans les postes -- Partie 10: Essais de
conformité
Ta slovenski standard je istoveten z: EN 61850-10:2005
ICS:
29.240.30 Krmilna oprema za Control equipment for electric
elektroenergetske sisteme power systems
33.200 Daljinsko krmiljenje, daljinske Telecontrol. Telemetering
meritve (telemetrija)
SIST EN 61850-10:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61850-10:2005

---------------------- Page: 2 ----------------------

SIST EN 61850-10:2005
EUROPEAN STANDARD EN 61850-10
NORME EUROPÉENNE
EUROPÄISCHE NORM June 2005

ICS 33.200


English version


Communication networks and systems in substations
Part 10: Conformance testing
(IEC 61850-10:2005)


Réseaux et systèmes de communication Kommunikationsnetze- und -systeme
dans les postes in Stationen
Partie 10: Essais de conformité Teil 10: Konformitätsprüfung
(CEI 61850-10:2005) (IEC 61850-10:2005)



This European Standard was approved by CENELEC on 2005-05-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 61850-10:2005 E

---------------------- Page: 3 ----------------------

SIST EN 61850-10:2005
EN 61850-10:2005 - 2 -
Foreword
The text of document 57/742/FDIS, future edition 1 of IEC 61850-10, prepared by IEC TC 57, Power
systems management and associated information exchange, was submitted to the IEC-CENELEC
parallel vote and was approved by CENELEC as EN 61850-10 on 2005-05-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2006-03-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2008-05-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61850-10:2005 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 61850-10:2005
- 3 - EN 61850-10:2005
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1)
IEC/TS 61850-2 - Communication networks and systems in - -
substations
Part 2: Glossary

1)
2)
IEC 61850-4 - Part 4: System and project management EN 61850-4 2002

1) 2)
IEC 61850-5 - Part 5: Communication requirements for EN 61850-5 2003
functions and device models

1) 2)
IEC 61850-6 - Part 6: Configuration description EN 61850-6 2004
language for communication in electrical
substations related to IEDs

1) 2)
IEC 61850-7-1 - Part 7-1: Basic communication structure EN 61850-7-1 2003
for substation and feeder equipment -
Principles and models

1) 2)
IEC 61850-7-2 - Part 7-2: Basic communication structure EN 61850-7-2 2003
for substation and feeder equipment -
Abstract communication service interface
(ACSI)

1) 2)
IEC 61850-7-3 - Part 7-3: Basic communication structure EN 61850-7-3 2003
for substation and feeder equipment -
Common data classes

1) 2)
IEC 61850-7-4 - Part 7-4: Basic communication structure EN 61850-7-4 2003
for substation and feeder equipment -
Compatible logical node classes and data
classes

1) 2)
IEC 61850-8-1 - Part 8-1: Specific Communication Service EN 61850-8-1 2004
Mapping (SCSM) - Mappings to MMS
(ISO 9506-1 and ISO 9506-2) and to
ISO/IEC 8802-3


1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 5 ----------------------

SIST EN 61850-10:2005
EN 61850-10:2005 - 4 -
Publication Year Title EN/HD Year
1) 2)
IEC 61850-9-1 - Part 9-1: Specific Communication Service EN 61850-9-1 2003
Mapping (SCSM) - Sampled values over
serial unidirectional multidrop point to
point link

1) 2)
IEC 61850-9-2 - Part 9-2: Specific Communication Service EN 61850-9-2 2004
Mapping (SCSM) - Sampled values over
ISO/IEC 8802-3

1) 2)
ISO/IEC 9646-1 - Information technology - Open Systems EN/ISO IEC 9646-1 1996
Interconnection - Conformance testing
methodology and framework
Part 1: General concepts

1) 2)
ISO/IEC 9646-2 - Part 2: Abstract Test Suite specification EN/ISO IEC 9646-2 1996

1) 2)
ISO/IEC 9646-4 - Part 4: Test realization EN/ISO IEC 9646-4 1996

1) 2)
ISO/IEC 9646-5 - Part 5: Requirements on test laboratories EN/ISO IEC 9646-5 1996
and clients for the conformance
assessment process

1) 2)
ISO/IEC 9646-6 - Part 6: Protocol profile test specification EN/ISO IEC 9646-6 1996

---------------------- Page: 6 ----------------------

SIST EN 61850-10:2005


INTERNATIONAL IEC


STANDARD 61850-10





First edition
2005-05


Communication networks and systems
in substations –
Part 10:
Conformance testing

 IEC 2005  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale X
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

---------------------- Page: 7 ----------------------

SIST EN 61850-10:2005
– 2 – 61850-10  IEC:2005(E)
CONTENTS
FOREWORD.4
INTRODUCTION.6

1 Scope.7
2 Normative references .7
3 Terms and definitions .8
4 Abbreviated terms .10
5 Introduction to conformance testing.11
5.1 General .11
5.2 Conformance test procedures.12
5.3 Quality assurance and testing .12
5.3.1 General .12
5.3.2 Quality plan .13
5.4 Testing .14
5.4.1 General .14
5.4.2 Use of SCL files .16
5.4.3 Device testing.16
5.5 Documentation of conformance test report .16
6 Device related conformance testing.17
6.1 General guidelines .17
6.1.1 Test methodology .17
6.1.2 Test system architectures.17
6.2 Conformance test procedures.18
6.2.1 General .18
6.2.2 Test procedure requirements .18
6.2.3 Test structure .19
6.2.4 Test cases to test a server .20
6.2.5 Acceptance criteria.37
7 Performance tests .38
7.1 General .38
7.2 Communications latency.38
7.2.1 Application domain .38
7.2.2 Methodology.39
7.3 Time synchronisation and accuracy.40
7.3.1 Application domain .40
7.3.2 Methodology.40
7.3.3 Testing criteria .41
7.3.4 Performance.41
8 Additional tests.41

Annex A (informative) Examples of test procedure template.42

Bibliography.43

---------------------- Page: 8 ----------------------

SIST EN 61850-10:2005
61850-10  IEC:2005(E) – 3 –
Figure 1 – Conceptual conformance assessment process .15
Figure 2 – Conceptual test system architecture.18
Figure 3 – Test procedure format.19
Figure 4 – Performance testing (black box principle).39
Figure 5 – Time synchronisation and accuracy test setup .40

Table 1 – Positive test cases .22
Table 2 – Negative test cases .22
Table 3 – Positive test cases .22
Table 4 – Negative test cases .23
Table 5 – Positive test cases .23
Table 6 – Negative test cases .24
Table 7 – Positive test cases .24
Table 8 – Negative test cases .25
Table 9 – Positive test cases .25
Table 10 – Negative test cases .25
Table 11 – Positive test cases .26
Table 12 – Negative test cases .28
Table 13 – Positive test cases .28
Table 14 – Negative test cases .29
Table 15 – Positive test cases .29
Table 16 – Positive test cases .30
Table 17 – Negative test cases .30
Table 18 – Negative test cases .31
Table 19 – Positive test cases .31
Table 20 – Positive test cases .31
Table 21 – Negative test cases .32
Table 22 – Negative test cases .32
Table 23 – Positive test cases .32
Table 24 – Test cases for SBOes.33
Table 25 – Test cases for DOns.34
Table 26 – Test cases for SBOns.34
Table 27 – Test cases for DOes.35
Table 28 – Negative test cases .35
Table 29 – Positive test cases .36
Table 30 – Negative test cases .36
Table 31 – Positive test cases .36
Table 32 – Negative test cases .37
Table 33 – Combination test case .37

---------------------- Page: 9 ----------------------

SIST EN 61850-10:2005
– 4 – 61850-10  IEC:2005(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________

COMMUNICATION NETWORKS AND SYSTEMS
IN SUBSTATIONS –

Part 10: Conformance testing


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61850-10 has been prepared by IEC technical committee 57:
Power systems management and associated information exchange.
The text of this standard is based on the following documents:
FDIS Report on voting
57/742/FDIS 57/749/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 10 ----------------------

SIST EN 61850-10:2005
61850-10  IEC:2005(E) – 5 –
IEC 61850 consists of the following parts, under the general title Communication networks
and systems in substations:
Part 1: Introduction and overview
Part 2: Glossary
Part 3: General requirements
Part 4: System and project management
Part 5: Communication requirements for functions and device models
Part 6: Configuration description language for communication in electrical substations
related to IEDs
Part 7-1: Basic communication structure for substation and feeder equipment – Principles
and models
Part 7-2: Basic communication structure for substation and feeder equipment – Abstract
communication service interface (ACSI)
Part 7-3: Basic communication structure for substation and feeder equipment – Common
data classes
Part 7-4: Basic communication structure for substation and feeder equipment – Compatible
logical node classes and data classes
Part 8-1: Specific Communication Service Mapping (SCSM) – Mappings to MMS (ISO 9506-
1 and ISO 9506-2) and to ISO/IEC 8802-3
Part 9-1: Specific Communication Service Mapping (SCSM) – Sampled values over serial
unidirectional multidrop point to point link
Part 9-2: Specific Communication Service Mapping (SCSM) – Sampled values over
ISO/IEC 8802-3
Part 10: Conformance testing
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.

A bilingual edition of this standard may be issued at a later date.

---------------------- Page: 11 ----------------------

SIST EN 61850-10:2005
– 6 – 61850-10  IEC:2005(E)
INTRODUCTION
This part of IEC 61850 is part of a set of specifications which details a layered substation
communication architecture.
This part of IEC 61850 defines:
• the methods and abstract test cases for conformance testing of devices used in
substation automation systems, and
• the metrics to be measured within devices according to the requirements defined in
IEC 61850-5.
The intended readers are test system developers.
NOTE 1 Tests regarding EMC requirements and environmental conditions are subject to IEC 61850-3 and not
included in this part of IEC 61850.
NOTE 2 It is recommended that IEC 61850-5 and IEC 61850-7-1 be read first in conjunction with IEC 61850-7-2,
IEC 61850-7-3, and IEC 61850-7-4.
NOTE 3 Abbreviations used in IEC 61850-10 are listed in Clause 4 or may be found in other parts of IEC 61850
that are relevant for conformance testing.

---------------------- Page: 12 ----------------------

SIST EN 61850-10:2005
61850-10  IEC:2005(E) – 7 –
COMMUNICATION NETWORKS AND SYSTEMS
IN SUBSTATIONS –

Part 10: Conformance testing



1 Scope
This part of IEC 61850 specifies standard techniques for testing of conformance of
implementations, as well as specific measurement techniques to be applied when declaring
performance parameters. The use of these techniques will enhance the ability of the system
integrator to integrate IEDs easily, operate IEDs correctly, and support the applications as
intended.
NOTE 1 The role of the test facilities for conformance testing and certifying the results are beyond the scope of
this part of IEC 61850.
NOTE 2 The test approach and test system design to test a client device is likely to be different across the broad
range of clients. There are many possibilities to test clients. The client tests are beyond the scope of this part of
IEC 61850. It is intended to define client test requirements during the maintenance of this part.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 61850-2, Communication networks and systems in substations – Part 2: Glossary
IEC 61850-4, Communication networks and systems in substations – Part 4: System and
project management
IEC 61850-5, Communication networks and systems in substations – Part 5: Communication
requirements for functions and device models
IEC 61850-6, Communication networks and systems in substations – Part 6: Configuration
description language for communication in electrical substations related to IEDs
IEC 61850-7-1, Communication networks and systems in substations – Part 7-1: Basic
communication structure for substation and feeder equipment – Principles and models
IEC 61850-7-2 , Communication networks and systems in substations – Part 7-2: Basic
communication structure for substation and feeder equipment – Abstract communication
service interface (ACSI)
IEC 61850-7-3 , Communication networks and systems in substations – Part 7-3: Basic
communication structure for substation and feeder equipment – Common data classes
IEC 61850-7-4 , Communication networks and systems in substations – Part 7-4: Basic
communication structure for substation and feeder equipment – Compatible logical node
classes and data classes
IEC 61850-8-1, Communication networks and systems in substations – Part 8-1: Specific
communication service mapping (SCSM) – Mappings to MMS (ISO 9506-1 and ISO 9506-2)
and to ISO/IEC 8802-3

---------------------- Page: 13 ----------------------

SIST EN 61850-10:2005
– 8 – 61850-10  IEC:2005(E)
IEC 61850-9-1, Communication networks and systems in substations – Part 9-1: Specific
Communication Service Mapping (SCSM) – Sampled values over serial unidirectional
multidrop point to point link
IEC 61850-9-2, Communication networks and systems in substations – Part 9-2: Specific
Communication Service Mapping (SCSM) – Sampled values over ISO/IEC 8802-3
ISO/IEC 9646-1, Information technology – Open Systems Interconnection – Conformance
testing methodology and framework – Part 1: General concepts
ISO/IEC 9646-2, Information technology – Open Systems Interconnection – Conformance
testing methodology and framework – Part 2: Abstract test suite specification
ISO/IEC 9646-4, Information technology – Open Systems Interconnection – Conformance
testing methodology and framework – Part 4: Test realization
ISO/IEC 9646-5, Information technology – Open Systems Interconnection – Conformance
testing methodology and framework – Part 5: Requirements on test laboratories and clients
for the conformance assessment process
ISO/IEC 9646-6, Information technology – Open Systems Interconnection – Conformance
testing methodology and framework – Part 6: Protocol profile test specification
3 Terms and definitions
For the purpose of this document, the terms and definitions provided in IEC 61850-2 as well
as the following definitions apply.
3.1
Factory Acceptance Test
FAT
customer agreed functional tests of the specifically manufactured substation automation
system or its parts using the parameter set for the planned application as specified in a
specific customer specification. The FAT will be carried out in the factory of the manufacturer
or other agreed-upon location by the use of process simulating test equipment.
3.2
hold point
point, defined in the appropriate document beyond which an activity shall not proceed without
the approval of the initiator of the conformance test. The test facility shall provide a written
notice to the initiator at an agreed time prior to the hold point. The initiator or his
representative is obligated to verify the hold point and approve the proceeding of the activity.
3.3
interoperability
ability of two or more IEDs from the same vendor (or different vendors) to exchange
information and use that information for correct co-operation.
A set of values having defined correspondence with the quantities or values of another set.
3.4
Model Implementation Conformance Statement
MICS
details the standard data object model elements supported by the system or device

---------------------- Page: 14 ----------------------

SIST EN 61850-10:2005
61850-10  IEC:2005(E) – 9 –
3.5
negative test
test to verify the correct response of a system or a device when subjected to:
– IEC 61850 series conformant information and services which are not implemented in the
system or device under test;
– non IEC 61850 series conformant information and se
...