SIST EN ISO 21043-1:2018

SLOVENSKI STANDARD
SIST EN ISO 21043-1:2018
01-december-2018
)RUHQ]LþQH]QDQRVWLGHO3RMPLLQGHILQLFLMH,62
Forensic Sciences - Part 1: Terms and definitions (ISO 21043-1:2018)
Forensik - Teil 1: Begriffe und Rahmenbedingungen (ISO 21043-1:2018)
Criminalistique - Partie 1: Termes, définitions et cadre d'emploi (ISO 21043-1:2018)
Ta slovenski standard je istoveten z: EN ISO 21043-1:2018
ICS:
07.140 Forenzika Forensic science
SIST EN ISO 21043-1:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 21043-1:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 21043-1:2018


EN ISO 21043-1
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2018
EUROPÄISCHE NORM
ICS 07.140
English Version

Forensic Sciences - Part 1: Terms and definitions (ISO
21043-1:2018)
Criminalistique - Partie 1: Termes et définitions (ISO Forensik - Teil 1: Begriffe und Rahmenbedingungen
21043-1:2018) (ISO 21043-1:2018)
This European Standard was approved by CEN on 21 July 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21043-1:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 21043-1:2018
EN ISO 21043-1:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 21043-1:2018
EN ISO 21043-1:2018 (E)
European foreword
This document (EN ISO 21043-1:2018) has been prepared by Technical Committee ISO/TC 272
"Forensic sciences" in collaboration with Technical Committee CEN/TC 419 “Forensic Science
Processes” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall
be withdrawn at the latest by March 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 21043-1:2018 has been approved by CEN as EN ISO 21043-1:2018 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 21043-1:2018

---------------------- Page: 6 ----------------------

SIST EN ISO 21043-1:2018
INTERNATIONAL ISO
STANDARD 21043-1
First edition
2018-08
Forensic sciences —
Part 1:
Terms and definitions
Criminalistique —
Partie 1: Termes et définitions
Reference number
ISO 21043-1:2018(E)
©
ISO 2018

---------------------- Page: 7 ----------------------

SIST EN ISO 21043-1:2018
ISO 21043-1:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 21043-1:2018
ISO 21043-1:2018(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
Bibliography . 5
© ISO 2018 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 21043-1:2018
ISO 21043-1:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 272, Forensic sciences.
A list of all parts in the ISO 21043 series can be found on the ISO website.
iv © ISO 2018 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 21043-1:2018
ISO 21043-1:2018(E)

Introduction
The development of international standards for forensic science is important to enhance the reliability,
transparency and confidence in forensic evidence. Standards will harmonize work practices to
facilitate forensic facilities from different countries to work collaboratively in response to cross border
investigations. They will also enable facilities from different countries to support one another in the
event of a catastrophic event that exhausts a country’s capabilities.
Standards will also facilitate the exchange of forensic results, information and intelligence, including the
sharing of databases, to ensure forensic services are fit for purpose. Standardization in the manner that
forensic evidence is collected, analysed, interpreted and reported is cr
...