SIST EN 2960:2020

SLOVENSKI STANDARD
SIST EN 2960:2020
01-maj-2020
Aeronavtika - Toplotno odporne zlitine na nikljevi osnovi (Ni-P101HT) - Hladno
preoblikovana in topilno žarjena - Palice za obdelavo pritrdilnih elementov - 3 mm
≤ D ≤ 50 mm
Aerospace series - Heat resisting nickel base alloy (Ni-P101HT) - Cold worked and
solution treated - Bar for machining for fasteners - 3 mm ≤ D ≤ 50 mm
Luft- und Raumfahrt - Hochwarmfeste Nickellegierung (Ni-P101HT) - Kaltverfestigt und
lösungsgeglüht - Stangen zur spanabhebenden Formgebung für Verbindungselemente -
3 mm < oder D ≤ 50 mm
Série aérospatiale - Alliage résistant à chaud base nickel (Ni-P101HT) - Écroui et mis en
solution - Barre pour usinage pour fixations - 3 mm ≤ D ≤ 50 mm
Ta slovenski standard je istoveten z: EN 2960:2020
ICS:
49.025.99 Drugi materiali Other materials
SIST EN 2960:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 2960:2020

---------------------- Page: 2 ----------------------
SIST EN 2960:2020


EN 2960
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2020
EUROPÄISCHE NORM
ICS 49.025.99
English Version

Aerospace series - Heat resisting nickel base alloy (NI-
P101HT) - Cold worked and solution treated - Bars for
machining for fasteners - 3 mm ≤ D ≤ 50 mm
Série aérospatiale - Alliage résistant à chaud base Luft- und Raumfahrt - Hochwarmfeste Nickellegierung
nickel (NI-P101HT) - Écroui et mis en solution - Barres (NI-P101HT) - Kaltverfestigt und lösungsgeglüht -
Stangen zur spanabhebenden Formgebung für
pour usinage pour fixations - 3 mm ≤ D ≤ 50 mm
Verbindungselemente - 3 mm ≤ D ≤ 50 mm
This European Standard was approved by CEN on 8 December 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 2960:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 2960:2020
EN 2960:2020 (E)
Contents Page
European Foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Requirements . 5
Bibliography . 8

2

---------------------- Page: 4 ----------------------
SIST EN 2960:2020
EN 2960:2020 (E)
European Foreword
This document (EN 2960:2020) has been prepared by the Aerospace and Defence Industries Association of
Europe — Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2020, and conflicting national standards shall be
withdrawn at the latest by September 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Irela
...