SIST EN ISO 20042:2021

SLOVENSKI STANDARD
oSIST prEN ISO 20042:2021
01-junij-2021
Merjenje radioaktivnosti - Radionuklidi, ki sevajo žarke gama - Splošna preskusna
metoda z uporabo spektrometrije žarkov gama (ISO 20042:2019)
Measurement of radioactivity - Gamma-ray emitting radionuclides - Generic test method
using gamma-ray spectrometry (ISO 20042:2019)
Mesurage de la radioactivité - Radionucléides émetteurs gamma - Méthode d’essai
générique par spectrométrie gamma (ISO 20042:2019)
Ta slovenski standard je istoveten z: prEN ISO 20042
ICS:
13.280 Varstvo pred sevanjem Radiation protection
oSIST prEN ISO 20042:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 20042:2021

---------------------- Page: 2 ----------------------
oSIST prEN ISO 20042:2021
INTERNATIONAL ISO
STANDARD 20042
First edition
2019-06
Measurement of radioactivity —
Gamma-ray emitting radionuclides —
Generic test method using gamma-ray
spectrometry
Mesurage de la radioactivité — Radionucléides émetteurs de
rayons gamma — Méthode d’essai générique par spectrométrie à
rayons gamma
Reference number
ISO 20042:2019(E)
©
ISO 2019

---------------------- Page: 3 ----------------------
oSIST prEN ISO 20042:2021
ISO 20042:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 20042:2021
ISO 20042:2019(E)

Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Symbols and units . 5
5 Principle . 6
5.1 General . 6
5.2 Summing method . 6
5.3 Fitting method . 7
6 Validating measurements by gamma-ray spectrometry . 7
6.1 General . 7
6.2 Step 1: customer requirements . 8
6.3 Step 2: technical requirements . 8
6.4 Step 3: detailed design .10
6.5 Step 4: installation .10
6.6 Step 5: validation studies .10
6.7 Step 6: robustness .11
6.8 Step 7: operation and maintenance .11
7 Nuclear decay data .11
7.1 Recommended nuclear decay data .11
7.2 Selection of gamma-ray photopeaks for inclusion in spectrum analysis libraries .12
7.3 Decay chains .12
8 Detector energy and efficiency calibration .13
8.1 Energy calibration .13
8.2 Efficiency calibration .13
8.3 Source(s) for energy calibration .14
8.4 Reference source(s) for efficiency calibration .15
8.4.1 General.15
8.4.2 Reference sources for laboratory systems .15
8.4.3 Reference sources used with numerical methods .15
9 Sample container .15
10 Procedure.16
10.1 Sample measuring procedure .16
10.1.1 Sampling.16
10.1.2 Sample preparation .16
10.1.3 Loading the sample container .18
10.1.4 Recording the sample spectrum .18
10.2 Analysis of the spectrum .18
10.2.1 Procedure for laboratory-based measuring systems .18
10.2.2 Background corrections .19
11 Expression of results .20
3
11.1 Calculation of activity and activity per kg (or m ) of sample .20
11.2 Determination of the characteristic limits .21
12 Test report .21
Annex A (informative) Quality assurance and quality control program .22
Annex B (informative) Corrections to the analysis process .24
Annex C (informative) Uncertainty budget .29
© ISO 2019 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 20042:2021
ISO 20042:2019(E)

Annex D (informative) Detector types .32
137
Annex E (informative) Example: Calculation of Cs activity content and characteristic
limits in an aqueous sample .35
Annex F (informative) Example: Simulating correction factors for sample positioning,
geometry, matrix, density and true summing .40
Bibliography .49
iv © ISO 2019 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 20042:2021
ISO 20042:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 85, Nuclear energy, nuclear technologies,
and radiological protection, SC 2, Radiological protection.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
© ISO 2019 – All rights reserved v

---------------------- Page: 7 ----------------------
oSIST prEN ISO 20042:2021
ISO 20042:2019(E)

Introduction
Everyone is exposed to natural radiation. The natural sources of radiation are cosmic rays and
naturally occurring radioactive substances which exist in the earth and flora and fauna, including the
human body. Human activities involving the use of radiation and radioactive substances add to the
radiation exposure from this natural exposure. Some of those activities, such as the mining and use
of ores containing naturally-occurring radioactive materials (NORM) and the production of energy
by burning coal that contains such substances, simply enhance the exposure from natural radiation
sources. Nuclear power plants and other nuclear installations use radioactive materials and produce
radioactive effluent and waste during operation and decommissioning. The use of radioactive materials
in industry, agriculture, medicine and research is expanding around the globe.
All these human activities give rise to radiation exposures that are only a small fraction of the global
average level of natural exposure. The medical use of radiation is the largest and a growing man-made
source of radiation exposure in developed countries. It includes diagnostic radiology, radiotherapy,
nuclear medicine and interventional radiology.
Radiation exposure also occurs as a result of occupational activities. It is incurred by workers in
industry, medicine and research using radiation or radioactive substances, as well as by passengers and
crew during air travel. The average level of occupational exposures is generally similar to the global
average level of natural radiation exposure (see Reference [1]).
As uses of radiation increase, so do the potential health risk and the public's concerns. Thus, all these
exposures are regularly assessed in order to,
a) improve the understanding of global levels and temporal trends of public and worker exposure,
b) evaluate the components of exposure so as to provide a measure of their relative importance, and
c) identify emerging issues that may warrant more attention and study.
While doses to workers are mostly measured directly, doses to the public are usually assessed indirectly
using the results of radioactivity measurements of waste, effluent and/or environmental samples.
To ensure that the data obtained from radioactivity monitoring programs support their intended use, it
is essential that the stakeholders (for example nuclear site operators, regulatory and local authorities)
agree on appropriate methods and procedures for obtaining representative samples and for handling,
storing, preparing and measuring the test samples. An assessment of the overall measurement
uncertainty also needs to be carried out systematically. As reliable, comparable and ‘fit for purpose’
data are an essential requirement for any public health decision based on radioactivity measurements,
international standards of tested and validated radionuclide test methods are an important tool for
the production of such measurement results. The application of standards serves also to guarantee
comparability of the test results over time and between different testing laboratories. Laboratories
apply them to demonstrate their technical competences and to complete proficiency tests successfully
during interlaboratory comparisons, two prerequisites for obtaining national accreditation.
Today, over a hundred International Standards are available to testing laboratories for measuring
radionuclides in different matrices.
Generic standards help testing laboratories to manage the measurement process by setting out the
general requirements and methods to calibrate equipment and validate techniques. These standards
underpin specific standards which describe the test methods to be performed by staff, for example, for
different types of sample. The specific standards cover test methods for
40 3 14
— naturally-occurring radionuclides (including K, H, C and those originating from the thorium
226 228 234 238 210
and uranium decay series, in particular Ra, Ra, U, U and Pb) which can be found in
materials from natural sources or can be released from technological processes involving naturally
occurring radioactive materials (e.g. the mining and processing of mineral sands or phosphate
fertilizer production and use), and
vi © ISO 2019 – All rights reserved

---------------------- Page: 8 ----------------------
oSIST prEN ISO 20042:2021
ISO 20042:2019(E)

— human-made radionuclides, such as transuranium elements (americium, plutonium, neptunium,
3 14 90
and curium), H, C, Sr and gamma-ray emitting radionuclides found in waste, liquid and gaseous
effluent, in environmental matrices (water, air, soil and biota), in food and in animal feed as a result
of authorized releases into the environment, fallout from the explosion in the atmosphere of nuclear
devices and fallout from accidents, such as those that occurred in Chernobyl and Fukushima.
The fraction of the background dose rate to man from environmental radiation, mainly gamma
radiation, is very variable and depends on factors such as the radioactivity of the local rock and soil, the
nature of building materials and the construction of buildings in which people live and work.
A reliable determination of the activity concentration of gamma-ray emitting radionuclides in various
matrices is necessary to assess the potential human exposure, to verify compliance with radiation
protection and environmental protection regulations or to provide guidance on reducing health risks.
Gamma-ray emitting radionuclides are also used as tracers in biology, medicine, physics, chemistry, and
engineering. Accurate measurement of the activities of the radionuclides is also needed for homeland
security and in connection with the Non-Proliferation Treaty (NPT).
This document describes the generic requirements to quantify the activity of gamma-ray-emitting
radionuclides in samples after proper sampling, sample handling and test sample preparation in a
testing laboratory or in situ.
This document is to be used in the context of a quality assurance management system (ISO/IEC 17025).
It forms the basis for measurement tasks using gamma-ray spectrometry, such as those set out in
ISO 18589-3, ISO 18589-7, ISO 10703, ISO 13164-2 and ISO 13165-3.
This document is one of a set of generic International Standards on measurement of radioactivity such
as ISO 19361.
© ISO 2019 – All rights reserved vii

---------------------- Page: 9 ----------------------
oSIST prEN ISO 20042:2021

---------------------- Page: 10 ----------------------
oSIST prEN ISO 20042:2021
INTERNATIONAL STANDARD ISO 20042:2019(E)
Measurement of radioactivity — Gamma-ray emitting
radionuclides — Generic test method using gamma-ray
spectrometry
1 Scope
This document describes the methods for determining the activity in becquerel (Bq) of gamma-ray
emitting radionuclides in test samples by gamma-ray spectrometry. The measurements are carried out
in a testing laboratory following proper sample preparation. The test samples can be solid, liquid or
gaseous. Applications include:
— routine surveillance of radioactivity released from nuclear installations or from sites discharging
enhanced levels of naturally occurring radioactive materials;
— contributing to determining the evolution of radioactivity in the environment;
— investigating accident and incident situations, in order to plan remedial actions and monitor their
effectiveness;
— assessment of potentially contaminated waste materials from nuclear decommissioning activities;
— surveillance of radioactive contamination in media such as soils, foodstuffs, potable water,
groundwaters, seawater or sewage sludge;
— measurements for estimating the intake (inhalation, ingestion or injection) of activity of gamma-
ray emitting radionuclides in the body.
It is assumed that the user of this document has been given information on the composition of the test
sample or the site. In some cases, the radionuclides for analysis have also been specified if characteristic
limits are needed. It is also assumed that the test sample has been homogenised and is representative of
the material under test.
General guidance is included for preparing the samples for measurement. However, some types of sample
are to be prepared following the requirements of specific standards referred to in this document. The
generic recommendations can also be useful for the measurement of gamma-ray emitters in situ.
This document includes generic advice on equipment selection (see Annex A), detectors (more detailed
information is included in Annex D), and commissioning of instrumentation and method validation.
Annex F summarises the influence of different measurement parameters on results for a typical
gamma-ray spectrometry system. Quality control and routine maintenance are also covered, but
electrical testing of the detector and pulse processing electronics is excluded. It is assumed that any
data collection and analysis software used has been written and tested in accordance with relevant
software standards such as ISO/IEC/IEEE 12207.
Calibration using reference sources and/or numerical methods is covered, including verification of
the results. It also covers the procedure to estimate the activity content of the sample (Bq) from the
spectrum.
The principles set out in this document are applicable to measurements by gamma-ray spectrometry in
testing laboratories and in situ. However, the detailed requirements for in situ measurement are given
in ISO 18589-7 and are outside the scope of this document.
This document covers, but is not restricted to, gamma-ray emitters which emit photons in the energy
range of 5 keV to 3 000 keV. However, most of the measurements fall into the range 40 keV to 2 000 keV.
The activity (Bq) ranges from the low levels (sub-Bq) found in environmental samples to activities
found in accident conditions and high level radioactive wastes.
© ISO 2019 – All rights reserved 1

---------------------- Page: 11 ----------------------
oSIST prEN ISO 20042:2021
ISO 20042:2019(E)

2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 542, Oilseeds — Sampling
ISO 707, Milk and milk products — Guidance on sampling
ISO 5500, Oilseed residues — Sampling
ISO 5538, Milk and milk products — Sampling — Inspection by attributes
ISO 5667-1, Water quality — Sampling — Part 1: Guidance on the design of sampling programmes and
sampling techniques
ISO 5667-10, Water quality — Sampling — Part 10: Guidance on sampling of waste waters
ISO 10703, Water quality — Determination of the activity concentration of radionuclides — Method by
high resolution gamma-ray spectrometry
ISO 11929, Determination of the characteristic limits (decision threshold, detection limit and limits of the
confidence interval) for measurements of ionizing radiation — Fundamentals and application
ISO 17604, Microbiology of the food chain — Carcass sampling for microbiological analysis
ISO 18400-101, Soil quality — Sampling — Part 101: Framework for the preparation and application of a
sampling plan
ISO 18400-102, Soil quality — Sampling — Part 102: Selection and application of sampling techniques
ISO 18400-103, Soil quality — Sampling — Part 103: Safety
ISO 18400-104, Soil quality — Sampling — Part 104: Strategies
ISO 18400-107, Soil quality — Sampling — Part 107: Recording and reporting
ISO 18400-202, Soil quality — Sampling — Part 202: Preliminary investigations
ISO 18400-203, Soil quality — Sampling — Part 203: Investigation of potentially contaminated sites
ISO 18400-204, Soil quality — Sampling — Part 204: Guidance on sampling of soil gas
ISO 18400-205, Soil quality — Sampling — Part 205: Guidance on the procedure for investigation of
natural, near-natural and cultivated sites
ISO 18589-2, Measurement of radioactivity in the environment — Soil — Part 2: Guidance for the selection
of the sampling strategy, sampling and pre-treatment of samples
ISO 18589-7, Measurement of radioactivity in the environment — Soil — Part 7: In situ measurement of
gamma-emitting radionuclides
ISO 24333, Cereals and cereal products — Sampling
ISO/IEC Guide 98-3:2008, Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in
measurement (GUM: 1995)
ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
2 © ISO 2019 – All rights reserved

---------------------- Page: 12 ----------------------
oSIST prEN ISO 20042:2021
ISO 20042:2019(E)

ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
3.1
background continuum
events in the spectrum that form a smooth curve onto which the photopeaks are superimposed
Note 1 to entry: The continuum may arise from gamma-rays scattered inside the test sample or any surrounding
materials, from cosmic radiation or from radionuclides in the surrounding materials.
3.2
blank sample
sample of a similar material to the test sample but containing radioactive impurities negligible in
comparison with the test sample
3.3
calcination
thermal treatment of the powder in order to remove volatile impurities or to change the density or
specific surface area of the powder
[SOURCE: ISO 13779-6:2015, 3.4]
Note 1 to entry: Calcination is commonly used for samples such as soil.
3.4
comminution
operation of reducing particle size by crushing, grinding or pulverisation
3.5
dead time
time during spectrum acquisition (real time) during which pulses are not recorded or processed
Note 1 to entry: Dead time is given by real time minus live time.
Note 2 to entry: The time is given in seconds.
3.6
decision threshold
value of the estimator of the measurand, which when exceeded by the result of an actual measurement
using a given measurement procedure of a measurand quantifying a physical effect, one decides that
the physical effect is present
[SOURCE: ISO 11929:2010, 3.6]
3.7
detection efficiency
probability that a gamma-ray emitted at a particular energy (keV) in the decay of a radionuclide in a
test sample is detected in the photopeak corresponding to that energy
3.8
detection limit
smallest true value of the measurand which ensures a specified probability of being detectable by the
measurement procedure
[SOURCE: ISO 11929:2010, 3.7]
© ISO 2019 – All rights reserved 3

---------------------- Page: 13 ----------------------
oSIST prEN ISO 20042:2021
ISO 20042:2019(E)

3.9
fractionation
separation of a product into several fractions by an appropriate technique such as distillation or
crystallization
[SOURCE: ISO 1998-4:1998, 4.20.300]
3.10
full width half maximum
FWHM
width of a gamma-ray p
...